-
Product
PXI 13 x DPDT Power Relays
40-130-102
-
Pickering Interfaces 40-130 DPDT Relay Modules are suitable for applications where ordinary reed relay modules require additional current/voltage capacity. It is available in a choice of 8 and 13 relay versions and has voltage handling up to 220VDC/125VAC and current handling to 2A . Connections are made via a front panel mounted 50 or 78 pin D-Type connector.
-
Product
PXI 8x SPST High Voltage Reed Relays
40-310-001
-
The 40-310/320 range of high voltage switching modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
Product
PXI Microwave Relay, Single SPDT, 26.5GHz, 50Ω, SMA, Internal Termination
40-781A-221
-
The 40-781A-221 (PXI) and 42-781A-221 (PXIe) are single SPDT 26.5GHz microwave relay modules with internal terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50GHz in 50Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
CMOS Drive DIL Reed Relays, Direct drive from 74HC or HCT
Series 98
-
Dual in line relays - high sensitivity. Dry or mercury relays with higher coil resistance than normal. 5, 12, or 24 volt coils with optional diode
-
Product
PXI 24 x DPST Reed Relays
40-115-122
-
Available in normally open (DPST & SPST) configurations. Connections are made via a front panel micro-D 96-pin male connector. For applications requiring improved bandwidth and crosstalk performance please look at our 40-120 and 40-125 range of shielded reed relay cards. General purpose reed relays are suitable for the construction of small switching networks, slaving up to larger switches or operating external devices (e.g. lamps, solenoids etc.). To simplify inter-relay wiring, interconnection points are built onto the circuit board easing the construction of complicated wiring.
-
Product
PXI/PXIe Microwave Relay, Quad SPDT, 67GHz, 50Ω, SMA-1.85
40-780B-574
-
The 40-780B-574 (PXI) and 42-780B-574 (PXIe) are quad SPDT 67GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions.
-
Product
PXI/PXIe Microwave Relay, Triple SPDT, 26.5 GHz, 50 Ω, SMA, Remote Mount, Failsafe
42-780B-533-E
-
The 40-780B-533-E (PXI) and 42-780B-533-E (PXIe) are triple failsafe SPDT 26.5 GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
Product
PXI/PXIe Microwave Relay, Quad SPDT, 40GHz, 50Ω, SMA-2.9
40-780B-544
-
The 40-780B-544 (PXI) and 42-780B-544 (PXIe) are quad SPDT 40GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
Product
PXI 75 x SPST Ruthenium Reed Relay Switching
40-140A-121
-
This range of high density reed relay switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose reed relays are suitable for the construction of small switching networks, for slaving up to larger switches or for operating external devices (e.g. lamps, solenoids etc.).
-
Product
PXI/PXIe Microwave Relay, Quad SPDT, 50GHz, 50Ω, SMA-2.4
40-780B-554
-
The 40-780B-554 (PXI) and 42-780B-554 (PXIe) are quad SPDT 50GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
Product
PXI-2520, 80-Channel, 2 A, SPST PXI Relay Module
778572-20
-
80-Channel, 2 A, SPST PXI Relay Module—The PXI‑2520 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2520 is fully software programmable, and it supports onboard relay count tracking. With an efficient coupling of voltage/current capability and relay density, this switch module is ideal for automated test equipment (ATE) loads or for controlling heaters, lights, and fans.
-
Product
8-CH Relay Outputs & 8-CH Isolated DI Card
LPCIe-7250
-
LPCIe-7250 provides 8-CH SPDT (Form C) relay outputs and 8-CH isolated digital inputs. The status of each relay output is represented by an onboard LED. When the relay is in SET condition, its corresponding LED will turn ON, and on the contrary, it is OFF. All digital input channels are non-polarity, optically isolated, and may be set to use RC filter or not. The devices are suitable for collecting digital inputs in noisy environments.
-
Product
Ultra High Density 4mm Reed Relays
120-1-A-3/2
-
Single Pole Reed Relays0.5 Amp switchingVery high packing densityStacking on 4mm x 4mm pitch1 Form A3 V Coil
-
Product
SIMRC - 8 x Reed Relay Module, SPST
1010-R-8-1-5/1D
-
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
PXI Dual Microwave SPDT Relay 12.4GHz 50 N-Type
40-780A-512
-
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
Product
PCI 50xSPST Shielded Reed Relay Card
50-125-121
-
The 50-110/115 range of switching cards are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female connector. For applications requiring improved bandwidth and crosstalk performance please look at our 50-120/125 range of shielded reed relay cards.
-
Product
PXI/PXIe Microwave Relay, Single SPDT, 50 GHz, 50 Ω, SMA-2.4, External Termination, Failsafe, Remote Mount
42-781A-721-E
-
The 40-781A-721-E (PXI) and 42-781A-721-E (PXIe) are single failsafe SPDT 50 GHz microwave relay modules with external terminations and remotely mounted relays. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
PXI Microwave Relay, Single SPDT, 26.5GHz, 50Ω, SMA, External Termination
40-781A-321
-
The 40-781A-321 (PXI) and 42-781A-321 (PXIe) are single SPDT 26.5GHz microwave relay modules with external terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50GHz in 50Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
PXI/PXIe Power Relay Module, 10xSPST, 30 Amp
40-166-001
-
The 40/42-166-001 is a PXI/PXIe high density power relay module with 10xSPST switches rated at 30A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations. It uses power relays which are suitable for switching loads up to 20A at 240VAC (SPDT & SP4T versions) or 30A at 277VAC (SPST versions).
-
Product
PXI/PXIe Power Relay Module, 18xSPST, 5 Amp, 37-pin D-type Connector
40-153-104
-
The 40/42-153-104 is a PXI/PXIe high density power relay module with 18xSPST switches rated at 5A. User connection is via a 37-pin D-type male connector. The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
Product
PXI Relay Driver Module
-
The PXI Relay Driver Module controls up to 64 external relays with up to 50 VDC or 600 mA per channel drive capacity when using an external power supply. Modules can drive small DC motors or other inductive relay coils, and they include overcurrent, overvoltage, and flyback protection to ensure long operation. The PXI Relay Driver Module allows you to build custom switch configurations while using the standard IVIcompliant NISWITCH driver software.
-
Product
PXI 2A Relay Module 26xDPDT
40-139-202
-
The 40-139 2A Relay Series is suitable for applications requiring medium power switching with high density.Featuring 2A current capacity and voltages to 300VDC/250VAC it is useful for cost critical applications.
-
Product
PXI/PXIe Power Relay Module, 36xSPST, 5 Amp, 50-pin SGMC Connectors, With Interlock
42-153-002-HI
-
The 40/42-153-002-HI is a PXI/PXIe high density power relay module with 36xSPST switches rated at 5A and includes the hardware interlock option. User connection is via 2x50-pin SGMC male connectors, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
-
Product
PXI/PXIe High Density Electro-mechanical Relay Module, 64xSPDT
40-148A-201
-
The 40-148A-201 (PXI) and 42-148A-201 (PXIe) 64xSPDT relay module is part of a range of high density switching modules available in Normally Open (SPST & DPST), Changeover (SPDT) and Normally Closed (SPST) configurations. Connections are made via a front panel 200-pin female connector.
-
Product
PXI Power Relay Module, 12xSPDT, 16 A
40-161A-101
-
The 40/42-161A-101 is a PXI/PXIe 12xSPDT power relay module and is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock. Electro-mechanical power relays are used wich are suitable for switching loads up to 16 A at 250 VAC.
-
Product
PXI/PXIe Power Relay Module, 8xSPDT, 5 Amp, 50-Pin SGMC Connector
42-158-004
-
The 40/42-158-004 is a PXI/PXIe high density power relay module with 8xSPDT switches rated at 5A. User connection is via a 50-pin SGMC male connector.
-
Product
PXI Quad Microwave SPDT Relay 26.5GHz 50 SMA
40-780A-534
-
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
Product
PXI General Purpose 2A Relay Module 16xSPDT, 78 D-sub
40-131-101
-
Low cost, general purpose electromechanical relay cards suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include switching of medium power AC and DC loads or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 50 or 78 pin D-Type connector plug.
-
Product
PXI/PXIe Microwave Relay, Single SPDT, 18 GHz, 50 Ω, SMA, External Termination, Failsafe, Remote Mount
42-781A-121-E
-
The 40-781A-121-E (PXI) and 42-781A-121-E (PXIe) are single failsafe SPDT 18 GHz microwave relay modules with external terminations and remotely mounted relays. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
PXI Microwave Relay, Dual SPDT, 26.5GHz, 50Ω, SMA, External Termination
40-781A-322
-
The 40-781A-322 (PXI) and 42-781A-3221 (PXIe) are dual SPDT 26.5GHz microwave relay modules with external terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50GHz in 50Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
