-
Product
Power Supply QD305 2x30V/5A
-
*on / off switch output section*two independent adjustable DC output*independent outputs serial and parallel*constant voltage and current*Low ripple and noise*four digit LED displays three*for 16 hours at full load*automatically search out
-
Product
Performance AC Power Source, 375 VA, 300 V, 3.25 A
6811C
-
Maximize your investment with five instruments in one device Increase your productivity with extensive built-in power measurement capabilities Flexible IO: LAN/LXI Core, USB and GPIB Lower your cost of ownership with global support & the longest standard warranty in the industry
-
Product
Intelligent Power Monitor
iPM
-
NAI’s iPM is an Intelligent Power Monitor that provides a precise, instrument grade, digital analysis of input power lines. This advanced, DSP-based unit monitors single-phase, 3-phase 4-wire wye, or 3-phase Delta power lines at various input voltage levels and frequencies.The iPM is equipped with an EIA RS485-compatible serial communications interface that permits additional control functions and readout of diagnostic data, and features a Background Built-in-Test (BIT) that constantly monitors the health of unit hardware and software. This power monitor is designed and qualified to the most stringent performance and environmental requirements, and is ideally suited for rugged defense and industrial applications.
-
Product
Switching Power Supply
-
A highly efficient electronic circuit that converts electrical power by rapidly switching a power transistor between full-on and full-off states at high frequencies.
-
-
Product
DC Blocking Power Splitter Combiner
PD5012
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)50 VDC maximum on DC block portsTri Alloy Type N Female (Jack) Low PIM
-
Product
RF Power Controller (ALC)
310-010030-004
-
The serial controlled ALC module is used to set and monitor the output level of your fixed gain RF amplifier. The module is available for many bands between 800 MHz and 3 GHz, and is configured and calibrated to meet your requirements.
-
Product
High Current DC Transformerd
-
High Current DC Transformer provides very accurate DC current measurements up to 3000 A with output current that varies directly with the input current in three ranges. This direct current transformer is designed with an open window to pass a single cable, set of cables, or buss bar that carry the direct current to be measured.
-
Product
High Speed DC Electronic Load
6330A series
-
The 6330A family offers 8 types of modular loads with power ranging from 30 watts to 1200 watts, current from 0.5mA to 240A, and voltage measurement from 0.5mV to 500V. Each load is isolated and floating, programmable in dual current range and measuring voltage range, and capable of synchronizing with other modules for control operating. The load can be operated in constant current, constant voltage, and constant resistance. With Synchronic parallel control capability, 6330A series loads allow users to parallel and synchronize more than one load together from an internal loading control signal. This feature provides synchronic dynamic loading test for multi-output power and high power test solution. Real time measurement of voltage, current, is integrated into each 6330A load module using a 16-bit precision measurement circuit. The user can perform on line voltage measurement and adjustment, or simulate short circuit test using the simple keypad on the front panel.
-
Product
Microwave Power Modules (MPMs)
-
In many modern military applications, stringent requirements for size and weight must be met without sacrificing power or performance. Our high-efficiency, conduction-cooled microwave power modules (MPMs) provide extremely dense packaging across the 2 – 40 GHz frequency band. dB Control’s MPMs are based on a modular design for easy customization and are available with continuous wave or pulsed power. Each MPM is a complete microwave amplifier that uses traveling wave tubes and solid state technologies to provide the best of both worlds for military and commercial applications.
-
Product
AUTOMATED POWER SUPPLIES/SWEEPERS FOR BWO
-
nsight Product Company offer Automated Power Supplies/Sweepers specially designed to control mm- and sub-mm wave BWO sources. Those power supplies provides:*highly stable regulated voltages for slow wave structure (anode), filament/heater and control electrodes;*special design to simplify operation with BWO or WRO tubes;*special design to protect tubes during Start/Stop;*unique possibility for fast frequency sweep within entire frequency band;*possibility to use tubes within a PLL frequency stabilization system;*digital control and digital indication of output frequency;*built-in IEEE-488 interface;*multiple possibilities to control output frequency
-
Product
DC Leakage Current Monitor
MDLA-100
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
This DC Leakage Current Monitor constantly observes leakage current of DC circuit like as PV generation system, etc. and lights up the warning lamp with signal output, when the leakage current exceeds the setting value.
-
-
Product
Power Analyzer
-
Shenzhen Graigar Technology Co.,Ltd.
This power analyzer is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The power analyser clamp is equipped with data logger.
-
Product
AC and DC 20-Amp Power Supply
ACDC-20
-
The ETI Model ACDC-20 is a rugged and portable 20-amp AC and DC power supply. Its applications include resetting circuit breaker charging motors and other general purposes. It will provide DC voltage in three nominal ranges from 0-120V, 240V, and 480V at 1.92 kVA, as well as AC voltage in three nominal ranges from 0-140V, 280V, and 560V at 2.8 kVA. The ACDC-20 is housed in a rugged plastic enclosure approximately 21.5” x 18.5” x 11.5” and weighs approximately 115 lbs.
-
Product
DC Source/Calibrators
-
Our DC Source/Calibrators are designed for a typical applications such as the design, check and calibration of high speed, high resolution A/D converters; design and certification of high speed data logging and process control systems; calibration of digital voltmeters and multimeters; as an “IMBEDDED STANDARD” and/or simulator; design, testing, simulation and certification of thermocouples, strain gages and transducer instrumentation.
-
Product
DC Power / Energy Absorber Test System
-
AMETEK Programmable Power, Inc.
The Energy Absorber Test System includes power supplies and a regenerative energy absorber with a rating of 400VDC at ±150A. The system consists of DC power supplies, an AC distribution and interlock system, an energy absorber chassis and an absorber load resistor chassis. The power sources are equipped with a remote control option allowing control via GPIB or with front panel controls in local mode. The operation of the specific parts of the system is described in the sections below.
-
Product
Power Supply Systems
-
The Auxiliary Power Unit (APU) serves as a cost effective solution for a variety of military vehicle platforms including main battle tanks, self-propelled howitzers, tactical vehicles, and other special purpose armored fighting vehicles. Our family of heavy-duty, automotive APUs for military applications are packaged to meet specific installation requirements and are available as stand-alone units or may be integrated with any combination of life support systems. Each system provides the following capabilities:
-
Product
High Power Femtosecond Lasers
-
The Carmel series offers a very compact design with free-space delivery wavelengths of 780 nm, 1550 nm, and now 1750 nm, pulse widths as short as 90 fs and power levels up to 2.5 W. In contrast, the Cazadero offers high pulse energies (up to 3 µJ) with pulse widths of < 500 fs at 1550 nm and user-selected repetition rates from MHz down to single pulse.
-
Product
Bipolar DC Power Supply / Battery Simulator
IT6400 Series
-
The unique bipolar voltage/current output makes IT6400 series can be used as a bipolar power source or a bipolar electronic load. The battery simulating function is especially applicable for development and high speed production testing of portable, battery-operated products.
-
Product
400-Watt DC/DC Converter
VPX55-3
-
NAI's VPX55-3 is 400-Watt DC/DC Converter that plugs directly into a standard 3U VPX chassis with a VITA 62 0.8" power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
Power Pass Hybrid Amplifier
AS 1313
-
- HIGH OUTPUT LEVEL- EXTERNAL PP SWITCH- LED FOR PP SELECTION- SEPARATE IN/OUT FUSES- HYBRID IC PROTECTED- DOUBLE OUTPUT 900 MHz
-
Product
UPS (Uninterruptible Power Supply)
-
The UPS (Uninterruptable Power Supply) by Allied Edison is a light weight (7.2 lbs), portable, non-variable source that converts a 12 Vdc Lithium Ion battery to output 110 vac sine wave at 60 hertz. It also has four 12Vdc output jacks, and 4 USB ports to power electronic equipment such as computers or used to supply cell phone chargers, etc. It has a strong built in flashlight. The UPS plugs into a standard 120 Vac, 60 hertz receptacle for charging and indicates percent battery capacity remaining on a digital meter located on the front panel. The UPS can also be charged by a solar cell, sold separately or can be plugged into a vehicles cigarette lighter receptacle for use in remote areas. The UPS is an excellent compliment to the VS-3 power supply where a technician needs a variable AC/DC source and cannot run a power cord due to the remoteness of the work area.
-
Product
Air Cooled Linear DC Electronic Load
ALx Series
-
The ALx Series utilizes conventional linear MOSFET-based dissipative elements, allowing the series to achieve a very wide voltage-current operating range within the model’s maximum power rating. Using the same heat management innovations developed for Magna-Power’s high density programmable DC power supplies, the ALx Series’ conservative cooling ensures long product life in environments up to 50 °C ambient operating temperature.
-
Product
Low PIM Coaxial Switch, DC to 20 GHz, SP4T
87104Q
-
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87104Q is a low PIM SP4T coaxial switch, operating from DC to 20 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency and ultimately maximizes test throughput.
-
Product
Power Amplifier
2734
-
The 2734 is a compact class D power amplifier, intended for acoustical measurements in the field or laboratory. All controls and connectors are placed on the front panel, enabling you to set up the 2734 very quickly, and to operate it in horizontal or vertical position. The 2734 is built into a robust flight case making it safe and easy to carry along.
-
Product
Power Supply Test System
-
The Procyon PTS 2100-10 is a configurable turnkey Power Test System, delivering automated test equipment (ATE) to some of the world’s largest-volume manufacturers as well as the affordability needed by niche market producers. Aerospace, defense, and avionics power supply ATE test systems applications include functional testing of AC and DC power supplies, generator, and engine control units, as well as a wide range of associated electronics.
-
Product
Ultra Low Level DC Voltage Amplifiers
-
The EM A10 is a low level amplifier module for sensitive measurements, data collection and systems, where signals below 1 nanovolt may be measured. It is ideal for the input unit for precision voltage measuring systems, requiring voltage sensitivity for measuring low noise and low impedance sources. The noise level of the A10 is equivalent to a perfect resistor of about 20 ohms. When used with a digital voltmeter, steady one nanovolt digits may be displayed, with a response time constant of less than a second. The input voltage stability of the A10 is very high, with the drift around a nanovolt per degree C. The input connectors are made from pure copper. The input impedance is very high, and is time dependent, determined by the loop gain.
-
Product
Power device test system
-
This system is suitable for DC testing of IGBT, IGBT module (1in1～7in1). Built-in hi-current switching relay circuit inside test head, it is capable ofDC testing from device itself to module. Highly accurate repeatability testing is available by high speed rise time which is suppressed its heat in hi-current
-
Product
Power Analyzers
-
At PCE Instruments you will find a power quality analyzer to measure the power in W, kWh or to analyze and measure harmonics. This power analyzer is a multi-function power analyzer device that measure precisely direct current, alternating current, AC-voltage, DC-voltage the intensity of DC or AC, phase rotation and idle, apparent and effective power. The reading of AC power is considered the real value and has a maximum range of 6000 Watts. While a reading is being taken, the polarity changes automatically, if negative values are taken then a minus sign will appear on the device display.Nowadays, power quality analyzers have many features such as, insulated current input, measurement of harmonics, AC and DC current measurement, AC and DC voltage measurement, frequency measurement, phase rotation measurement and idle, apparent and effective power measurement. All this data can also be logged and analyzed with the delivered PC-Software. Power analyzers of the type PCE PA 6000 can determine the energy in single-phase systems.Power quality analyzers of type PCE-GPA 62 allow the energy measurement in symmetrically loaded three-phase systems. Power analyzers of type PCE-PA 8000, PCE-360 and PCE-830 support professional power and energy measurements in single and three-phase systems.Apart from being used as energy-measuring devices, power analyzers like the PCE-830 can also be used for network analysis and the determination of harmonics and phase rotation. On our website you will find other power analyzers used in the field of electronics.
