-
Product
PCI 8x9 RF Coaxial Matrix Card 50Ω SMB
50-725A-511
-
The 50-725A is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz. The 50-725A is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
PXIe-5668, Up to 26.5 GHz PXI Vector Signal Analyzer
783156-01
-
Up to 26.5 GHz PXI Vector Signal Analyzer - The PXIe‑5668 offers wide bandwidth with high-performance measurement performance and speed. It meets the challenging requirements of applications such as wireless communications, radio frequency integrated circuit characterization, RADAR test, and spectrum monitoring and signal intelligence. With its implementation as a PXI instrument, the PXIe‑5668 also features the fast measurement speed required for high-volume manufacturing test, and multi-instrument synchronization capabilities for phase-coherent MIMO test. You can use the optionally included PXIe-5698 preamplifier to improve dynamic range and sensitivity near the instrument noise floor.
-
Product
L-Band RF Tuner and 2-Channel 200 MHz A/D with Virtex-6 FPGA - XMC
Model 71690
-
- Accepts RF Signals from 925 MHz to 2175 MHz- Programmable LNA boosts LNB (low noise block) antenna signal - levels with up to 60 dB gain- Programmable analog downconverter to I + Q baseband signals - 4 to 40 MHz bandwidth- Two 200 MHz 16-bit A/Ds digitize the I + Q signals synchronously- Supports Xilinx Virtex-6 LXT and SXT FPGA- 2 GB DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1 & 2) interface, up to x8- Clock/sync bus for multimodule synchronization- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Pulsed And CW EPR/ESR: Synthesizers Up To 280 GHz
-
Insight Product Company offers synthesizers at frequencies from 30 to 280 GHz which can be used in EPR/ ESR experiments. These sythnesizers are designed to go swiftly from the generation to the non-generation mode and back. This process is controlled by external TTL signal. There is also the possibility to manipulate the phase, namely to shift it by 90 degrees and 180 degrees. ON/OFF switch time is approximately 2 nanoseconds.
-
Product
PIN Solid State Switch, 100 MHz to 8 GHz, SPDT
P9402A
-
The Keysight P9402A PIN solid state switch maximizes your operating frequency range from 100 MHz to 8 GHz. Providing superior performance in terms of isolation, insertion loss and return loss, the P9402A is particularly suitable for high-speed RF and microwave switching applications such as switch matrixes in instrumentation, communications and radar. These switches provide ultra-fast switching speed to increase throughput in manufacturing.
-
Product
6 GHz ProLink Differential Probe with Adjustable Tip
D600A-AT-PL
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
PXI Single 16 to 1 RF MUX MCX 75 Ohm
40-835-101
-
The 40-835-101 is a single 75 Ohm 16-channel RF MUX in a single PXI slot. The module has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The design of the 40-835 minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
Product
Saluki S5700 Series Field Comm Analyzer (SA/CA/OPTICAL)
-
S5700 Series Field Comm Analyzer combines the highest performance operating specifications and multi-functional measurements such as cable and antenna system analysis, fiber inspection, spectrum analysis, cellular signal demodulation, interference analysis, signal coverage mapping and RF/optical power measurements in a single instrument.
-
Product
PXI/PXIe RF Matrix, 8x4, 300 MHz, 50 Ω MS-M Multiway With Loop-thru
42-729A-002-L
-
The 40-729A-002-L (PXI) and 42-729A-002-L (PXIe) are 8x4 50 Ω RF matrices with MS-M Multiway connectors and Y-axis loop-thru. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
Product
PXI/PXIe RF Multiplexer, Quad 4-Channel, 3GHz, 50Ω, SMB
40-872A-004
-
The 40-872A-004 (PXI) and 42-872A-004 (PXIe) are 50 Ohm 4 to 1 RF multiplexers available with 4 banks in a single PXI slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
Field Test Interface Kit
2200
-
TESCO’s new Field Test Interface Kit (Catalog No. 2200) provides metering professionals with exceptional testing flexibility. The Field Test Interface includes a zero insertion force (ZIF) meter socket, voltage and form selection, and connection points to link it with a TESCO Field Test Kit (Catalog No. 621, 630 or GA Series). When combined with a Field Test Kit and powered via inverter (commonly used on service trucks), the Field Test Interface will then power the Field Test Kit to create a single position, stand-alone, meter accuracy testing device for various socket based meters (both mechanical & solid-state). Power for the Field Test Interface can also be supplied by customer potential via TESCO Field Test Kit (no need for the inverter).
-
Product
InfiniiMax II Series Probe Amplifier, 10 GHz
1168B
-
Provides a large common mode range and a large offset range for measuring differential and single-ended signals.
-
Product
3 GHz RF/IF Sentinel Intelligent Signal Scanning Portable Recorder
Talon RTR 2613
-
The Talon® RTR 2613 combines Pentek’s Sentinel Intelligent Signal Scanning software with real-time recording in a lightweight, portable and rugged package. The RTR 2613 provides SIGINT engineers the ability to scan the 3 GHz spectrum for signals of interest and monitor or record bandwidths up to 40 MHz wide once a signal band of interest is detected. The RTR 2613 recorder is a grab-and-go recorder suitable for test & measurement, mobile military, security and government intelligence (SIGINT, COMINT and ELINT) applications.
-
Product
Deep Access RF Probes
-
GigaTest Microwave Probes are perfect for device characterization and modeling. GigaTest Probes have a high tolerance allowing them to land repeatedly and take high-quality data.
-
Product
PXI/PXIe RF Multiplexer, Single 4-Channel, Terminated Common, 3GHz, 50Ω, SMB
40-876A-001
-
The 40-876A-001 (PXI) and 42-876A-001 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 1 bank in a single slot. Additionally, extra switching allows the common connection to be terminated into 50 Ohm, maintaining signal integrity. The module exhibits low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
RF Proximity Detector
Type RPD-2 AND Type RPD-2A
-
The Type RPD-2 Radio Frequency (RF) Proximity Detector is designed to detect and locate devices that radiate radio waves in the high frequency to low microwave frequency range. Such devices often include surveillance and “spy” equipment. The Type RPD-2, when used with the different sensors, will detect the emanation of the radio wave within a confined area, and then isolate its location to within approximately a square foot. The type RPD-2A may be used as an RF field strength indicator for antenna field strength measurements. The RPD-2A is identical in function except that the meter scale is calibrated in relative dB units.
-
Product
"Standard" RF Low Pass Filters
-
Coaxial Dynamics "Standard" line of RF Low Pass Filters offers several models to choose from at CW power ratings of 100 watts and 200 watts. These filters cover operating frequencies from 88 MHz to 400 MHz with less than 0.5 dB insertion loss and attenuation levels of 40, 50 and 60 dB.
-
Product
DC-40 GHz High Performance Modular Microwave Switch (2U)
EX72SF
-
Combine up to 6 SPDT and 6 multiport high-performance building blocks in a 2U footprintExtended life and self-terminating options provide maximum design flexibilityEmbedded web interface provides interactive utility to monitor and control relays from anywhere in the worldFlexible API supports IVI and Linux development environments minimizing software investment
-
Product
PXI 8x4 RF Matrix 300MHz 50 Multiway Connector With Loop-Thru
40-729-002-L
-
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
PXI Dual 4 to 1 RF Multiplexer 2GHz 75 Ohm SMZ/Type 43
40-746-711
-
40-740, 40-745 and 40-746 RF Multiplexers are a range of Bi-Directional Multiplexers with bandwidth up to 2000MHz. They are arranged as Single 8 to 1, Dual 4 to 1 or Single 4 to 1 configurations, all with excellent Insertion Loss, VSWR and Isolation, in 50 Ohm or 75 Ohm versions with a wide choice of connectors.
-
Product
Field Effect Rectifiers
-
ST field-effect rectifier diodes (FERD) help improve designs with new versions focusing on trade-off upgrades. Field-effect rectifier diodes belong to our STPOWER family. The design of the FERDs has allowed both a decrease in the voltage drop and a decrease in the leakage current temperature coefficient. As a result, the runaway safety margin is improved and maybe beyond the typical safety margin of Schottky barrier diodes.
-
Product
TERAHERTZ ROOM TEMPERATURE DETECTORS FROM 37.5 GHZ To 996 THz
-
Insight Product Company offers Golay cells that detect electro-magnetic waves at terahertz frequency ranges from 0.0375 to 996 THz.
-
Product
High Frequency RF and Microwave USB Programmable Signal Generators
LMS Series
-
The Lab Brick LMS series of high frequency RF and microwave USB-compatible, synthesized signal generators cover a frequency range from 0.5 MHz - 20 GHz with low noise, fast 100-microsecond switching time, and fine 100 Hz frequency resolution. They require no additional DC supply voltage and offer advanced features such as phase-continuous linear-frequency sweeping, internal/external 10 MHz reference, and optional pulse modulation. GUI software can track and control several connected signal generators, simplifying multiple-signal test setups. Each device stores settings in internal memory, allowing it to power up in a specific instrument state.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 6 GHz, 50 Ω, SMA, Failsafe
42-784B-002
-
The 40-784B-002 (PXI) and 42-784B-002 (PXIe) are dual failsafe SP6T 6 GHz unterminated microwave multiplexers. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
Product
Active Differential Probe, 100 kHz to 7 GHz
U1818A
-
The Keysight U1818A 100 kHz to 7 GHz active differential probe makes it easy to perform high frequency in-circuit measurements using network, spectrum and signal source analyzers. With flat frequency response, low noise floor, and direct power from instrument connection, the U1818A allows measurements to be made while taking full advantage of Keysight's RF analyzers dynamic range.
-
Product
4-in-1 OSLT Calibration Kit, DC to 70 GHz, Type-1.85 mm (m)
CK058M
-
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
Product
Comb Generator, 10 MHz to 26.5 GHz
U9391C
-
The Keysight Technologies, Inc. U9391C comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
Product
PXI/PXIe RF Matrix, Dual 2x2, 2.5GHz, 50Ω, SMB
40-877A-002
-
The 40-877A-002 (PXI) and 42-877A-002 (PXIe) are 50Ω 2x2 RF matrices with 2 banks in a single slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-877A modules. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
Microwave Switch RF Switch - 26.5G AXIe
RF Switch-26.5G AXIe Module
-
The RF Switch-26.5G AXIe module is designed to work as part of information measuring systems as a radio frequency signal switch (one input to six outputs for each of the eight input lines).
-
Product
Waveguide Harmonic Mixer, 33 to 50 GHz
11970Q
-
The Keysight 11970Q waveguide mixer is a general-purpose harmonic mixer employing a dual-diode design to achieve flat frequency response and low conversion loss. These are achieved without external dc bias or tuning stubs. Manual operation and computer-controlled hardware operation are simplified because mixer bias and tuning adjustment are not required.
