-
product
3 3/4 Digit Autoranging Digital Multimeter w/Bargraph
HH2204
High Accuracy (Basic Accuracy 0.5%). Jumbo LCD display 3260 count, 27mm figure height. Auto Ranging or Manual Ranging at your choice. Higher Voltage test up to AC 750V and DC 1000V. Higher Current test up to 20A. Resistance test up to 30MΩ. Frequency test range up to 3000Hz. Diode test, audible continuity check and Transistor test
-
product
14-Bit PCI Express Digitizer
SIS1160-SFMC01
The SIS1160-SFMC01 is the combination of the SIS1160 carrier with the SFMC01 2 channel 2.5 GSPS 14-bit digitizer FMC.
-
product
Bench Digital Multimeter, Calibrated, Data, 1 kV, 10 A, 3.8 Digit
72-1015 CAL D
The 72-1015 CAL D from Tenma is a digital bench type true RMS multimeter. It has auto and manual range options with maximum reading of 5999 counts and 3-5/6 digits which has a unique outlook design. In addition to all the conventional features including DC/AC voltage, current, resistance, diode, continuity test, diode test capacitance, temperature, transistor, max/min, there is a data hold, low battery display, sleep mode, RS232C serial port for easy connection with computer to realize macro recording, monitoring and capture of transient dynamic data, displaying change of waveform during the measurement, providing data and evidence to engineering technicians for scientific research. This meter complies with the standards IEC61010, pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) double insulation and CE marked.
-
product
Digital Signal Processor
HSR40 CC
Curtiss-Wright Defense Solutions
Curtiss-Wright’s CHAMP-XD2 digital signal processor (DSP) card handles the incoming data and features two multi-core Xeon D processors and two built-in 40 GbE interfaces. The processor hosts a Linux operating system and runs the HSR40 data recording and storing application. The processors can easily absorb the incoming data and redirect it to the persistent storage media, using 3rd generation PCI Express (PCIe), enabling the efficient movement of all the data.
-
product
Digital Anemometer w/ Humidity Tester
DAFM3B
UEi Test & Measurement Instruments
The DAFM3B Anemometer/ Psychrometer meter is designed with 6 HVAC/R must have parameters in one instrument. These are included in a portable battery operated instrument for measuring humidity, air temperature, dew point and calculating wet bulb, air velocity and air volume. The sensor is built into the remote fan and is specially protected by a twist cap. While in operation, open the cap for accurate temperature and humidity readings.
-
product
Calibration Short For Digital Multimeters
34172B
The Keysight 34172B digital multimeter calibration short is a set of two shorts which provide a convenient and reliable method to apply a short to the input connectors of the multimeter. Terminals are made of low-thermal copper alloys to minimize thermally-induced voltages caused by dissimilar metals.
-
product
PXI Digital IO
The Keysight M9187A Digital I/O provide static digital input and output channels which can be used in applications that require the monitoring of digital states and the controlling of external devices. These are typically used in aerospace/defense, automotive, and electronic test applications. The module offers configuration flexibility with programmable input thresholds and flexible output drive capability.
-
product
Digital Multi-Meter
7124A
Peaceful Thriving Enterprise Co Ltd
This is a low power consumption, high accuracy, and stable hand held 3 1/2digits (2000 counts) multimeter; with special designed IC to support true RMS measurement. It performs measurements of DC voltage / current, true RMS AC voltage / current, resistance, diode, continuity, and non-contact voltage sensing.
-
product
NI-6583, 200 MHz, 32 Single-Ended and 16 LVDS Channels, Digital I/O Adapter Module for FlexRIO
781320-01
200 MHz, 32 Single-Ended and 16 LVDS Channels, Digital I/O Adapter Module for FlexRIO—The NI-6583 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 32 single-ended and 16 low-voltage differential signaling (LVDS) digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6583 can sample digital waveforms at up to 200 MHz. It includes support for selectable single-ended voltages from 1.2 to 3.3 Volts with 10 bit resolution and common LVDS voltages.
-
product
High-Speed Digitizers and Multichannel DAQ Solutions
With our high-speed digitizers, we improve your measurement fidelity, signal integrity and measurement throughput, keeping low the total cost of ownership. The entire range includes PCIe, PXIe and AXIe form factors, configurable in single to multichannel solutions. Our products cover several applications in commercial OEM, aerospace & defense, wireless & RF communication and high-energy physics.
-
product
Multi-Function Digital Pattern Generator & Logic Analyzer
GP-241xx Series
Multi-function PC digital interface for digital IC and embedded system testing and debugging.
-
product
Digital Control Step Attenuator
Digital control attenuators with TTL parallel control offering fast switching speed and high attenuation accuracy
-
product
Digital Earth Resistance Testers
This groundmeter is designed for testing ground wire of electric power net, as well as earth voltage test in the fields of household electric power system and delectric appliance application.
-
product
LCR Digital Bridge
FD2810B
• Test parameter: C, R, L, Z, D, Q• Test frequency: 100Hz, 120Hz, 1kHz, 10kHz• Test level range: 0.1V, 0.3V, 1.0V• Output impedance: 30Ω, 100Ω• Slow or fast (15 times/s)• Automatic selecting, out of limit alarming• Provide the RS-232 & HANDLER interface• Accuracy: 0.1%
-
product
5 Digit Frequency Meter
CS1-F
CS1-F economic type Frequency Meter is designed with high accuracy measurement, display and communication of Frequency.The innovation feature is auto-range input from 0.01Hz~100KHz(option ~140KHz) and the display resolution will auto-change to show the highest according to input frequency.They are also available 1 option of 1 Relay outputs, 1 Analogue output or 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission or communication for a wide range of panels and testing applications.
-
-
product
Digital Pressure Modules
Practical Instrument Electronics, Inc.
Choose from 32 different digital pressure modules that simply connect to your PIE 820Elite, PIE 830 or PIE 850 calibrator via a communications cable. Software is pre-loaded on your PIE calibrator so you can add pressure modules to your toolbox at any time. Pressure module is automatically detected upon connection to your calibrator.
-
product
Serial to Digital Interface
All of ICS's Serial Digital Interfaces are user configurable and let you transfer data as bits, bytes or as strings of bytes. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard and are HP-IB compatible.
-
product
PXIe-6547, 100 MHz, 32-Channel PXI Express PXI Digital Waveform Instrument
781011-03
PXIe, 100 MHz, 32-Channel PXI Express PXI Digital Waveform Instrument—The PXIe‑6547 is a digital waveform generator and analyzer for interfacing and basic characterization test with 32 single-ended digital pins. The device is capable of sampling digital waveforms at up to 100 MHz and interfacing with user-programmable voltage levels that have a 100 mV resolution. The PXI‑6547 also features advanced synchronization capabilities for building integrated mixed-signal test systems, hardware comparison for bit-error test, and per-bank digital timing features.
-
product
Digital Signal Processors
Powerful Field Programmable Gate Array (FPGA) based Digital Signal Processors (DSP) with large memory, fast PCIe and optical data interfaces (ODI)
-
product
Digital Indicating Pressure Transmitter
DSGT
Series DSGT Digital Indicating Transmitter is a versatile multi-function process gage that features an excellent 0.25% full scale accuracy.
-
product
Digital Force Gauges
Imada digital force gauges are highly accurate instruments that provide the precise force measurement required in quality testing that determines strength and/or functionality of a part or product. Digital gauges can be used for destructive or non-destructive force measurement applications and check both compression and tension (push or pull) forces. The high sampling rate of Imada digital gauges enables them to capture the peak force of destructive tests which occurs in milliseconds. Imada digital force gauges also feature selectable units: lbf, kgf and N and easy-to-program high/low setpoints for Go/No Go testing.
-
-
product
Digital Circuit Breaker Analyzer
CT-3500 S2
The CT-3500 S2 is Vanguard’s second generation, stand-alone, digital, microprocessor-controlled, circuit-breaker timer. It measures the elapsed time from the instant a breaker coil is energized to the instant of opening or closing of a circuit-breaker’s dry contacts. In addition to timing a breaker’s contact response time, the CT-3500 S2 can also time relays or other switching functions that use an initiating trigger voltage (24-300 Volts DC or AC). The timer-triggering voltage starts three independent electronic timers. Each timer is individually stopped by its respective dry-contact closing or opening. The CT-3500 can fully analyze the timing of all circuit breaker operations (Open, Close, Open – Close, and Close – Open). Timing results are displayed in milli-seconds and cycles on the unit’s back-lit LCD screen and can be printed on the built-in 2.5-inch wide thermal printer.
-
product
PXI Digital Multimeter
PXI Digital Multimeters, or DMMs, feature AC/DC voltage, AC/DC current, 2- or 4-wire resistance, and frequency/period measurements, as well as diode tests. You can also choose a PXI DMM with an isolated, high-voltage digitizer that can acquire waveforms at sample rates up to 1.8 MS/s at full input range, up to 3 A or 1,000 V. Additionally, you can choose a PXI DMM that can perform basic inductance and capacitance measurements.
-
product
Digital Source Capture Unit
DIO2
The DIO-II module is a multimode digital source and capture unit. In Low Speed Mode it provides a 20-bit parallel or 24-bit serial I/O capability running at speeds up to 50 MHz. In High Speed Mode, the DIO-II provides a 16-bit parallel I/O capability up to 200 MHz. In both Modes, the Clock is generated by a low jitter PLL source that is capable of generating clocks from 320 kHz up to 1 GHz.
-
product
Digital Low Range TDS Pen
CD97
The Milwaukee CD97 Total Dissolved Solids Low Range (PPM) Pen is designed for water conditioning, education and many other applications. The CD97 helps you make sure that your keep your filters up-to-date and clean for water filtration and is a cost effective tool for teacher's science labs. Keep PPM in your target range to help your achieve better results.
-
product
Digital Signal Processing (DSP)
Abaco has an extensive track record in helping our customers turn sensor-acquired data into actionable information in the shortest time and at the lowest bandwidth in a broad range of digital and analog applications.
-
product
4 Digit Process Meter
CM2-PR
CM2-PR Process Meter has been designed in simple operation and 4 digital 20mm LED display with economic cost.They are can be programmed by buttons that are hidden in front panel.They are also available to option 2 relay output and an analog output or RS485(Modbus RTU Mode) communication.
-
product
Digital Control Step Attenuator
RF Lambda’s digital control step attenuators are used to fine tune an RF signal using TTL control lines. Fast response time, various step sizes and overall attenuation ranges make these suitable for a variety of RF applications. Hermetically sealed options are available upon request.
