-
Product
Primary Injection Test Systems
-
Primary current injection testing is utilised in high current/high voltage scenarios found at large electrical installations such as substations. A large current (between 100A and 20,000A depending on system specifications and test requirements) is injected directly on the primary side of the electrical system such as a circuit breaker. The objective of the test is to identify how the system operates under various levels of current load.
-
Product
4G, 3G and 2G Device Testing
-
Wireless network emulators enable the entire mobile device ecosystem to accelerate delivery of 5G new radio (NR) products.
-
Product
Lithium Battery Test Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Lithium battery test chambers are used to simulate various extreme conditions such as crush, impact, penetration, overcharge etc the lithium ion cells and batteries are subjected to during use, transportation, storage and disposal to determine the safety performances, tests including altitude simulation test, thermal test, vibration test, shock test, external short circuit test, impact/crush test, overcharge test, discharge test etc based on UN38.3, IEC62133, UL1642 standards. Applicable to communication products, computer products, consumer electronics, automobile power supplies and so on.
-
Product
Heuristics Testing Browser Add-On
-
Convenient access to common boundaries and edge cases for exploratory testing. Tiny overhead per page (<1k), no 3rd party library dependencies, completely passive, so it does not interfere with your web app execution in any way. Works on input fields, text areas, content editable DIVs. Load your own config files. Opensource, so you can easily extend it with your config.
-
-
Product
Motor Test for Stepping Motors
-
*Stable measurement: Since it uses Prony braking, this model provides stable measurement unaffected by moments of inertia and no coupling loss. In addition, the resulting measurements allow data correlation via the traditional double-balance method.*Precision measurement method: This model’s judgment of synchronization loss achieves high stability using algorithms developed by Sugawara Laboratories. Measurement mode can be chosen based on step angle. For pull-in torque, startup can be measured consistently from the holding state. Allows measurement at 1-Hz resolution.*Broad measurement range: This model offers a range of seven available measurement heads, from 0.5 N to 50 N, allowing use for high-precision measurements. Through selection and use of pulleys, this model can also be used to measure small motors of 0.5 mN·m or less or 500 mN·m motors. Pulley diameters and other settings are easily configured using a personal computer running Windows®. Note: Any of the seven available heads may be attached to a single measurement component.*High-visibility measurement data: Motor characteristics are easily ascertained on automatically plotted performance graphs. Measurement data can be overlaid up to four times. In addition, the cursor can be used to read accurate values from measurement points. Hard copies of data displayed on-screen can be printed from a personal computer.*Can be controlled using standard personal computers: Allows control of measurement operations and display and storage of data from a standard personal computer running Windows®. Data is stored in CSV-format files for compatibility with other software applications.
-
Product
Tenney Walk-In Environmental Test Chamber
-
Tenney’s multipurpose environmental walk-in room is the perfect test site for everything from testing against humidity, temperature and various climate conditions. This walk-in chamber provides supreme temperature testing for large components and equipment. When your testing requires walk-in rooms, choose Tenney. Our test rooms feature automated process control, energy efficiency, and a vast range of features and options.
-
Product
Device Thermal Test Systems
-
Thermal Engineering Associates, Inc.
Thermal test system combines the test and measurement capability of dedicated instruments with the ease of operation and data collecting capability offered by graphical-user-interface-driven software operating on an integrated computer.Diodes (PN, Schottky, LED, varactor, PIN), Stacked Diodes (Hi-V Rectifiers & LEDs), Laser Diodes, Transistors (Bipolar, MOSFET, IGBT) & Diodes, Integrated Circuits (Application & Thermal Test Die).
-
Product
Software Testing & Quality Assurance Services
-
We have deep expertise in various spheres: finance, banking, e-commerce, education, healthcare, entertainment, telecom, travel, aviation, natural resources and others. Our strong quality assurance team can start testing your project of any complexity within 24 hours. Convenience for TestMatick`s customers consists in the proper mix of technical skills of the team, understanding of the business process, special industry knowledge, professionally built testing processes and methodology. Mobile Application and Smartphone Testing: We ensure quality of the entrusted to us mobile software products carefully testing them on the required mobile platforms. Automated Software Testing For Quality Assurance. T
-
-
Product
Ionic Contamination Test Equipment
-
For manufacturers driven to deliver quality products, SCS Ionic Contamination Test Systems are the industry standard, delivering accuracy and performance in a range of configurations.
-
Product
Laser Test Systems
-
Santa Barbara Infrared, Inc. offers an extensive family of test systems and components that test and characterize the performance of laser range finders, designators, illuminators and spot trackers.
-
Product
Scanning Head For Energy Meter Test
PACB108
-
PACB08 is the accessory device to perform the energy meter test, which can work together with PONOVO’s relay test sets to test energy meter by using Energy Meter Module in Powertest software.
-
Product
Low Pressure/Temperature Test Chamber
-
Dongguan City Simplewell Technology Co. Ltd.
Low Pressure/Temperature Test Chamber by Simplewell
-
Product
EMC Testing
-
EMI is emitted radiation and its effects – a phenomenon. EMC is a device’s ability to limit the levels of unintentionally emitted EMI (that can harm other devices) and also a device’s ability to operate normally when subjected to EMI. Therefore, EMC testing seeks to ensure that a product possesses the characteristic of Electromagnetic Compatibility (EMC): the ability to limit creation of EMI (Electromagnetic interference) and the ability to operate properly when subjected to EMI. Stated differently, EMC testing measures the level of EMI control found in a device, and therefore helps to ensure that unwanted effects are prevented.
-
Product
USB PD Test System
6050
-
Single Output USB PD USB PD basic version：the single-group test systemarchitecture is as shown in the table, 5302A AC Source, 3302F + 3310F series and9922-R Quick Charge Controller.
-
-
Product
Pump Test System
-
This automated test system evaluates a wide range of performance metrics for a cooling pump assembly. The LabVIEW based system programs the DUT then initiates a series of tests to check:Serial communication verificationMotor voltage & currentImpeller speed and flowAir and water temperaturesLeak and level sensor functions
-
Product
Website Testing Tool
SortSite
-
SortSite automatically scans entire websites for over 450 quality issues including: accessibility; browser compatibility; broken links; legal compliance; search optimization; usability and web standards.
-
Product
Test Management And Reporting Software
-
AFL’s PC- and cloud-based software solutions provide both the knowledge and the power to analyze your data and generate standard or custom reports that provide actionable intelligence for your business
-
Product
Oil Test Set
-
RR-OIL TEST SET also known as OIL BDV KIT is an equipment-designed and produced to test the ELECTRICAL STREGTH of Liquid Insulating Materials such as Transformer Oil, Capacitor Oil etc. The test set carries out test on these materials as per Indian Standard Specification IS 6792. This Oil Test Set is essential for Transformer & Switchgear Manufacturers, also for oil filtration units.
-
Product
Test Probes / Test Fixtures
-
INGUN has an unbeatable assortment of test probes and test fixtures for individual testing tasks.Thanks to many years of experience in the testing equipment field, INGUN offers the suitable test solution for every test requirement.
-
Product
ICT Test Probes
-
C.C.P. Contact Probes Co., LTD.
Our In-Circuit Test Probes are used for all kinds of PCB tests. We offer a standard portfolio as well as customized parts.
-
-
Product
Interoperability Testing Services
-
Using our decades of knowledge and experience of Bluetooth, markets and products we'll help you deliver products which are free of defects, minimize field issues, lower development costs and reduce time to market. Teledyne LeCroy offers test services to help in all stages of product development from Specification to Market Launch and beyond.
-
Product
Computer Control Tensile Testing Machine
SG-L03B
-
These series of universal testing machine are used to test tension, compression, bend, shearing force, adhesion, peeling force, tear strength,...etc. of specimen, semi-product and finished product in the field of rubber, plastic, metal, nylon, fabric, paper, aviation, packing, architecture, petrochemistry, electric appliance, automobile,...etc. , which are the basic facilities for input quality contorl (I.Q.C), Quality Control (Q.C.), Physical Inspection, Mechanics Research and Material.
-
Product
Unit Testing Mocking Solution for .NET
Suggest
-
Suggest creates automatic test suggestions suitable for your code.
-
Product
(100kN) Fatigue Testing Systems
8801
-
The 8801 servohydraulic testing system meets the challenging demands of a varied range of both dynamic and static testing requirements. The 8801 provides complete testing solutions to satisfy the needs of advanced materials and component testing, and is ideally suited for high- and low-cycle fatigue testing, thermomechanical fatigue testing, and fracture mechanics. The higher capacity of up to 100 kN, a larger working space, a high stiffness, and the precision of alignment all make the 8801 an exceptionally versatile and reliable testing system.
-
Product
Mobile App Testing Company
-
ImpactQA’s Mobile Testing services offer comprehensive testing strategies that attend to device and network infrastructure. We offer an effective combination of manual and automated tools to cover functional and non-functional software issues. Selecting the right mobile test automation strategy is crucial for creating optimal mobile applications. At ImpactQA, we make sure you have the best options and choose the correct tools and processes suited for testing your mobile websites and native mobile apps. ImpactQA has wide experience in mobile testing for varied domains such as Insurance, Banking, Retail, Healthcare, E-learning, Media, BFSI, E-commerce, and Real Estate leveraging leading industry best practices and tools.
-
Product
Multifunction Substation Test Set
STS 5000
-
STS 5000 is a multifunction substation maintenance & commissioning test system for current, voltage and power transformers designed to perform primary tests requested in substations commissioning. It allows to perform accurate tests on CTs, VTs, PTs and ground grid.
