-
Product
Benchtop with Drop-In Test System
600 Series Compact ATE Platform
-
The Circuit Check 600 Series Compact ATE Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 600 Series Compact ATE, test procedures can become automatic, with test steps and go/no-go limits easily programmable. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
-
Product
Safety Testing
-
Seaward's high quality electrical safety testing equipment has a worldwide reputation for technical excellence in the appliance, electrical and electronics manufacturing sectors.
-
Product
Integrating Sphere Systems
-
An optical device for various purposes such as. measuring the radiant flux (optical power) from a laser diode, light-emitting diode (LED) or bulb.
-
Product
Testing Framework
TestDrive
-
TestDrive™ automates all types of testing for data integration applications for dramatically improved quality of applications as well as the data they produce.
-
Product
Environmental Testing
-
Transcat is your premier provider of environmental testing. We carry an extensive inventory of test & measurement equipment, with over 3000 products available for same-day shipping. For many instruments, new instrument calibration is also available, ensuring that your product is tested and ready for use as soon as you get it.
-
Product
Test System
DA-1 ATS
-
The DA-1 ATS is an economical Commercial-Off-The Shelf (COTS) build-to-print tester. The test station is compliant with the published drawing package. The system does not include software.
-
Product
Module Sockets
Ardent Optical Engine
-
The scalability of SP connector technology is enabling the next generation of optical device IC manufactures to allow for solder-less high speed optical Electrical Module replace-ability. These connectors offer high speed input data rates in cost effective and real-estate friendly form factors.
-
Product
Climate Test
Series C
-
With our CTS climatic test chambers, you can also simulate the stress factor humidity in your tests next to the temperature. The humidity is measured by a capacitive moisture sensor, which is characterized by high accuracy, long term stability and low maintenance.
-
Product
Mixed Signal Test Systems
MTS2010i
-
The MTS-2010i are a cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process.
-
Product
Electrical Test System TY-CHECKER
Type P Series
-
Manual press systems made to suit your purpose.
-
Product
Microwave Testing
50A
-
The GGB Industries, Inc., MODEL 50A probe sets new standards in microwave probing performance. Using low loss coaxial techniques, the Model 50A achieves an insertion loss of less than 1.0 db and a return loss of greater than 18 db through 50 GHz.
-
Product
Compression, Paper And Pulp Test Systems
-
From basic tension and compression testing to advanced materials testing
-
Product
Source / Measure Unit (SMU) Modules, N6700 Power System
-
The Keysight N6780 family of source/measure units (SMUs) provide advanced features and precise control and measurements of voltage and current down to the microampere and nanoampere regions. They provide stable, glitch-free output voltage and current during high-speed load changes, fast output modulation, and high-speed measurements of both voltage and current simultaneous.
-
Product
RSP-2T Test System Interface Probe
RSP-2T
-
Current Rating (Amps): 5Average Probe Resistance (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 167Full Travel (mm): 4.24Recommended Travel (mil): 79Recommended Travel (mm): 2.00
-
Product
Connector Test
-
A connector test system which provides expansion of up to 160 Kelvin pair connections. The system incorporates high voltage AC and DC power supplies with a maximum output of +/- 2100 Volts peak for Hi Pot, Insulation resistance measurement. LCR bridge control is provided with 4 terminal multiplexing in order to add precision capacitance, inductance and resistance measurement capability. An integral H.V. capacitor bias option permits capacitance measurement to be made at up to 2.1kV.
-
Product
Magnetic System
NMR-EA300 System
-
The NMR-EA300 system is the reference for calibrating magnetic sensors. It allows to generate an absolute magnetic field at <±10mG (0.1 uT) without temperature drift (<0.1ppm/C°) over a range from 14mT to 3T. This system is composed of an EA300 electromagnet with NMR poles, a MPU-16U ±150A ±70V current source of class 1ppm and a NMR20 Teslameter with a magnetic field controller (FR020).A thermostat chamber can be installed in the air gap (Optionally available on 50mm and 70mm gap poles).
-
Product
Loudspeaker Testing
TTC
-
The weakest link in your measurement chain is your chamber, the new TTC chambers solve these problems...*Anechoic chambers have massive footprints:The TTC gives you equal or better results with a compact footprint*Achieving repeatable measurements is difficult in an anechoic chamber:The TTC guarantees the microphone and loudspeaker positions*Anechoic chamber accuracy suffers at low frequencies:The TTC is capable of measuring below 20 Hz*Results are not transferable between most test chambers:The TTC meets international standards IEC 60268-21:2018 & IEC 60268-22:2020*Most chambers are difficult to calibrate and awkward to use:The TTC is calibrated and is ready to interface to your microphone and analyzer
-
Product
Design and Development: Complete Systems and System Components
-
Custom Systems Integration Inc.
CSI''s design and development (D&D) organization has the resources, skill and experience to design a complete turnkey system, a system component or collaborate with customer''s internal staff on any part of a system.
-
Product
TEST SOCKET
-
IC Package It is a device to install INTERFACE between TESTER and DEVICE during TEST to check electrical defects such as O / S (Open, Short) test, mounting test, BURN-IN TEST and RLC TEST, The device
-
Product
Compliance Test Systems
LMG Test Suite
-
ZES ZIMMER Electronic Systems GmbH
The ZES ZIMMER test system LMG Test Suite tests in accordance with the currently valid version of EN 61000-3-2/-12 or EN 61000-3-3/-11 and also supports measurements per ECE R-10.4 Annex 11 (e.g. electromagnetic compatibility of vehicles). As a manufacturer of precision power measurement technology, we are represented on the international standards committee. As a result, changes in standards are immediately incorporated into our test systems.
-
Product
Security Testing
-
For an application to be successful, it has to ensure the security of the customer’s data, which in turn helps to gain the trust of the customers, avoid legal battles, and enables growth in business.
-
-
Product
Field Testing
-
Electronic force measuring device with digital display in MN / m², switchable for load plate.
-
Product
System Integration
-
More and more customers want integrated systems in which the devices are supplemented with additional components and delivered turnkey. ET System electronic offers all services for this system integration from a single source. The sources and electronic loads are fully wired according to customer requirements, installed in 19 "cabinets and equipped with special features. For example, sources and loads can be combined with one another and supplemented with special interfaces or emergency stop functions. The integration of insulation monitors, interlock functions and the installation of industrial PCs is also possible, as is the installation of special safeguards, for example if each channel is to be safeguarded separately in multi-channel devices.The respective configuration can be based on any machine guidelines and standards, and the systems can be integrated into any existing environment with additional connections. On request, space and connection options for additional devices can be provided in the 19 “cabinets so that customers can easily integrate their own components.
-
Product
Amplifier Systems
-
Systems are complete. They plug into an outlet and are ready to go. Our standard systems are 3U, which is 5.25″ and 5U, 8.75″. Systems are available with or without IEEE-488, RS-232 and Ethernet connectivity. Amplifiers Systems are available in both Broadband and Band-Specific frequencies.
-
Product
Automated Warning System
-
Is a safety system consisting of 3 different magnet types (AWS 1, 2 and 3) and a locomotive-mounted detector (MagSense), designed to aid drivers in observing the fixed signals, particularly under adverse weather conditions, and is supplementary to the fixed signals which the driver must observe.
-
Product
Temporary Bonding Systems
-
Temporary bonding is an essential process to offer mechanical support for thin or to-be-thinned wafers, important for 3D ICs, power devices and FoWLP wafers, as well as for handling fragile substrates like compound semiconductors. A device wafer is bonded to a carrier wafer with the help of an intermediate temporary bonding adhesive, allowing the typically fragile device wafer to be processed with additional mechanical support. After the critical processes, the wafer stack is debonded. EVG’s outstanding bonding know-how is reflected in its temporary bonding equipment, which has been provided by the company since 2001.
-
Product
Low-Tc Systems
-
With our long year experiences in SQUID electronics, SQUID sensors, and SQUID systems, we can offer exactly the system you need. No matter if you need a small 5 litres LHe dewar with just a single channel or a 100 litres multichannel system, we cooperate with excellent dewar manufacturers to guarantee the best possible performance for the overall system.
-
Product
Qualmark HASS Systems
-
Advanced environmental test chambers that combine rapid temperature changes with multi-axis vibration to quickly find product weaknesses and eliminate defects in electronics and electromechanical devices.
