-
Product
Interface Test System (ITS)
-
The SecuControl ITS is a modular test block designed to meet the stringent safety, reliability, and performance needs of IEC-based substations. With fully finger-safe construction, keyed STP test plugs, and built-in CT Shorting, the ITS enables safe, repeatable secondary injection testing, without the risk of open CT circuits or accidental trips. It is the ideal solution for structured, standardized testing across protection systems.
-
Product
Phantom Load Test Set
-
Is a testing accessory, wisely designed for field testing service. This equipment helps in providing artificial load that is unaltered by the change in power supply.
-
Product
Fixtures, Programming & Test Services
-
Comware Technical Services, Inc.
Fixtures and programming services are available for Agilent, GenRad, and Teradyne testers. Working from CAD data, a program can be created in only a few days allowing for fast and cost effective testing of your products. Engineering services are available for fixture revisions or repairs.
-
Product
Altitude Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
The altitude test chambers of Sanwood Technology is designed to allow users to perform temperature, humidity, and altitude condition tests in a combined test chamber, and create multiple conditions to meet multiple test requirements at the same time.
-
Product
UDP Test Tool, Flood Generator, VoIP Readiness Test Tool
-
The Multiprotocol Network Tester is a freeware, open source tool which enables you to measure quality of your IP network. It can also be used to generate UDP flood or to simulate UDP DoS attack. SIP call is usually established using a SIP session with a bidirectional RTP stream. SIP and RTP protocols are based on UDP transport protocol. UDP uses a simple transmission model without implicit reliability, ordering and data integrity. Each single UDP packet is transferred independently. The quality of a SIP call depends on delays and loss of IP packets in a network. Long delays lead to large RTP jitter and bad sound quality of a SIP call.
-
Product
Power Device Testing System
-
Devices that control electric power, and are used in automobiles and a wide range of electrical products.
-
Product
Testing Services
-
Koehler Instrument Company, Inc.
A complete source for your testing solutions, Koehler offers a wide range of in-house testing services based on selected standard test methods. Our staff is comprised of technical experts and the best instrumentation for fast, accurate and reliable results. We specialize in all tests for which we offer instrumentation as well as additional test methods. You are invited to send us samples for testing and evaluation at any time. Please contact your Koehler representative for additional information.
-
Product
Compact Ultrasonic Testing Device
SONAPHONE® Pocket
-
With the SONAPHONE Pocket you identify problems even before they arise and create value at all levels of your company. Just by detecting and eliminating leaks you can reduce the energy costs for your compressed air system up to 30 percent. This also has positive effects on your operational safety and system productivity through early warning of bearing failure and evidence of partial electrical discharges.
-
Product
Three-Phase Meter Test Equipment
ASTEL 3.2 TYPE
-
ASTeL 3.2 meter test equipment is a fully automatic system that enables simultaneous, multi-position calibration and verification of three-phase electric energy meters. ASTeL 3.2 offers full compatibility with IEC 60736. Thanks to excellent parameters, superior functionality and outstanding flexibility, ASTeL 3.2 is an ideal solution for utility companies, energy meter manufacturers, governmental institutes of metrology, metrological laboratories, and other customers interested in electricity meters testing.
-
Product
Test Accessories
-
Qosmotec Software Solutions GmbH
Qosmotec test systems are expandable to adapt your automation environment to increased demands. Standard components that can be easily integrated into an existing test setup are
-
Product
Automotive Test Scopes
-
Scientech Technologies Pvt. Ltd.
Automotive Test Scopes by Scientech
-
Product
Video Test Pattern Suite
Sarnoff®
-
In the digital era, traditional video test and measurement tools are becoming obsolete. SRI offers a suite of unique visual tools that enable users to stress, evaluate, and calibrate audio and visual equipment throughout the signal chain. Test pattern products include the award-winning Visualizer digital video test pattern, the ESP encoder stress pattern, and the TSG test sequence generator.
-
Product
Performance Testing Services
-
Alphabin Technology Consulting
There are over 1.5 million mobile apps that are abandoned due to performance issues. Guard your application with our performance testing services.
-
Product
Flow Battery Test Stations
-
Greenlight's turn-key flow battery test systems include load/power supply modules, automated control of flow, pressure and temperature of electrolyte fluids, cell voltage monitoring, 3-level safety system and computer with Emerald dynamic automation software. All Greenlight flow battery test systems come with a our standard 1 year warranty. Our customer service team is available to travel to your facility for commissioning and training.Greenlight''s Automation Division also offers flow battery assembly equipment.
-
Product
Fused Visible & IR Testing
-
SBIR offers a visible/NIR/I-Squared/IR target projector that features a fused visible and thermal source capability by combining a MWIR and LWIR differential blackbody source with a visible/NIR integrating source. A beam-combiner allows the thermal energy and the visible energy to be processed simultaneously on the optical centerline of the collimator.
-
Product
Leak Testing
-
Leak testing is a non-destructive method to verify the presence of a leak in a component or device.It is implemented as a control methodology for monitoring production process and product quality control. Leak tests are used to find out possible leaks due to non-suitable material (porosity, blowholes, cracks), or in the machining process to find out machining errors or defective parts, and ultimately in assembly, to find out missing or defective gaskets, wrong positioning or assembly. The presence of a leakage could jeopardize the correct functioning of the component, device or its life span, and can also be potentially dangerous for the environment and the safety of its user.
-
Product
Heat Detector Testing
Solo 423 / 424
-
Available in both 110 / 120 and 220 / 240 volt versions the Solo 423 and 424 are the professionals’ choice where cables and leads are acceptable. Unconstrained by energy availability they provide the quickest of test times and are, perhaps, most suitable for the highest temperature detectors.
-
Product
Bit Error Rate Testing
-
Anritsu is a world leader in Bit Error Rate test and measurement products. These products reflect that global leadership, addressing data rates from 100 Mbit/s to 64.2 Gbit/s.
-
Product
Circuit Breaker Test System
TDR900
-
It operates and records a circuit breaker’s contact timing, motion, velocity, main contact engagement & synchronization, trip and close coil initiation and currents.
-
Product
Commodity Classification Testing
-
Underwriters Laboratories Inc.
As a global expert in fire safety science, UL provides an independent assessment of the fire risks associated with various types of stored commodities protected by sprinklers. As a part of commodity classification testing, UL examines many factors including sprinkler activation temperature, sprinkler response time index (RTI), the radial distance from the sprinkler to the center of the fire, the distance between the ceiling and the top of the commodity, and the number of storage tiers.
-
Product
Testing of Electrical Safety
-
Manufacturers and operators of electrical equipment are required to carry out an electrical safety test within the framework of the applicable regulations. This is to prevent accidents caused by malfunctions in electrical equipment, such as fire, explosion as well as injuries and personal damage. The tests to be carried out are specified in national (VDE/DIN) and international (EN/IEC) standards. After passing the test, the product is considered safe for the entire life cycle, provided it is left in its original condition and used for its intended purpose.
-
Product
Test Benches
-
Atec has made test equipment throughout all of its 65-year history. Test benches for aerospace and energy uses represent a significant segment of our experience. Atec has produced test benches involving hydraulics, mechanicals, electromechanicals, electronics, pneumatics, motors, and digital automation. Atec test benches have performed for challenging measurements, factory production, problem analysis and component overhaul scenarios. Today, complex test benches have capable data acquisition, control and communication systems integral in their electronics. Atec’s ADAQ™ system, based on COTS components and software, is proven and popular in test bench applications. DCUs, ECUs, FADECs and earlier analog or mechanical control units are easily interfaced.
-
Product
Test Bench For Circuit Breaker
-
SCR ELEKTRONIKS have developed Test Bench for Circuit Breaker to test 2, 5 & 10 at a time. Panel is provided with constant DC current source.
-
Product
Software Testing Tool
LanTraffic V2
-
LanTraffic V2 is a software testing tool allowing UDP and TCP traffic generation on an IP network.
-
Product
Relay Test Kit
Relaystar-H60
-
HAOMAI Electric Power Automation Co., LTD.
Portable 6-phase protection test equipment for testing most types of modern multi-function protection relays, Output 6-phase AC current 6x0…32A Output 4-phase Voltage 4x0…300V.
-
Product
Materials Test System
ModuLab XM MTS
-
I-V (voltage scans with current measurement - used to characterize electronic and dielectric materials)P-E (polarization / electric field - used to run hysteresis tests to characterize ferroelectric materials) High-speed pulse (used to activate charge carriers in electronic and dielectric materials)Staircase and smooth stepless analog ramp waveformsImpedance, admittance, permittivity / capacitance, electrical modulusC-V capacitance - voltage, Mott-SchottkyAutomatic sequencing of time domain and impedance/capacitance measurements
-
Product
Meter Test Station
WECO 8000
-
The innovative WECO 8000 Meter Test Station is the first of its kind – a multi-position test board integrating meter qualification and accuracy. This versatile and economic test station is the solution for utilities needing the ability to switch between functional testing and accuracy testing. Separate multi-position test boards are no longer a necessity.
-
Product
Chloride Test System
C-CL-2000
-
The C-CL-2000 produces results on-site, within minutes that are accurate and comparable to expensive laboratory tests. It measures the electrochemical reaction of a weighted sample placed in an extraction liquid. It automatically shows a temperature compensated reading of percent of chlorides on its digital display. A wide range - from 0.002 to 2% chloride by weight - is covered.
-
Product
Lab Inspection & Testing Services
-
Our lab services use advanced techniques to thoroughly inspect components for manufacturing flaws before assembly. We work with clients in the aerospace, automotive, oil & gas, manufacturing, wind energy, and various other industries to ensure their materials and components are free from defects that were introduced in forging or manufacturing processes.
-
Product
Test Equipment Calibration Services
-
Custom Calibration Solutions, LLC
Custom Calibration Solutions assists customers in meeting or exceeding individual business goals by striking the ultimate balance between quality objectives and cost. We can optimize any existing test equipment calibration program by combining the use of our proprietary procedures in conjunction with the most appropriate standards for each calibration task.
