-
product
Transition Module for 3U cPCI IP Carrier
TCP010-TM
The TCP010-TM is a Transition Module to be used with 3U cPCI IP carrier, providing easy access to the IP I/O lines of cPCI IP carrier with back I/O.
-
product
Digital Source Capture Unit
DIO2
The DIO-II module is a multimode digital source and capture unit. In Low Speed Mode it provides a 20-bit parallel or 24-bit serial I/O capability running at speeds up to 50 MHz. In High Speed Mode, the DIO-II provides a 16-bit parallel I/O capability up to 200 MHz. In both Modes, the Clock is generated by a low jitter PLL source that is capable of generating clocks from 320 kHz up to 1 GHz.
-
product
Industrial Flash & Memory Solutions
Advantech provides a full range of industrial storage module, memory module, and embedded I/O module.
-
product
10-32 Coaxial Male to BNC Female, 50 Ohm, 3 ft. cable
786657-01
10-32 Male to 1-Pin BNC Female, 50 Ohm Coaxial Cable - The 1032CoaxialM-BNC Cable connects data acquisition (DAQ) and control devices such as C Series I/O modules.
-
product
Digital I.O Module with 64 TTL Channels
IO203
This I/O module is a dedicated digital I/O module providing a total of 64 TTL channels. The TTL transceivers are TTL and CMOS/TTL compatible and can also set to be CMOS compliant by the Setup driver block. Each of the 64 channels can individually be programmed as input or output. The 64 channels are further separated into two groups of 32 channels each.
-
product
cDAQ-9191, 1‑Slot, Ethernet and 802.11 Wi‑Fi CompactDAQ Chassis
781497-01
1‑Slot, Ethernet and 802.11 Wi‑Fi CompactDAQ Chassis - The cDAQ‑9191 is a Wi‑Fi chassis designed for small, remote, or distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. You can send data from the cDAQ‑9191 to a host PC over Ethernet or IEEE 802.11 Wi‑Fi. The chassis also has four 32‑bit general‑purpose counters/timers built in. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
product
Automation Systems
Omron's extensive portfolio of PLC and MAC controllers, networking solutions, remote IO, IPC and HMI technology support a fully integrated application
-
product
256 Digital Input/Output Channels
CP387
The C387 is a single-width, 6U, CompactPCI module with up to 256 digital input/output channels. The C387 base board supports 128 channels of TTL I/O. Four mezzanine card sites can be populated with other forms of digital I/O including isolated input, isolated output, relay output, AC switch output or differential I/O. The mezzanine card concept allows multiple digital I/O types to be configured within a single module to match the application requirements.
-
product
Static Digital I/O Instrumentation
High-speed and static 3U and 6U PXI and PCI digital I/O instrumentation. Offering test rates to 200 MHz and programmable logic levels of -10 V to +15 V, our digital products feature the highest performance and most cost effective digital test solutions in the industry.
-
product
DSP Module
CPCI-QIPC-6U
The CPCI-4pack-6U module provides a high performance flexible I/O scheme, that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the CPCI-4pack-6U is the perfect solution. The Local DSP can be used to simply move data to and from the CPCI bus or provide pre processing functions such as local PID controls, FFT’s, digital filtering, etc. Custom application software can be downloaded to the DSPvia the CPCI bus or the local serial port.
-
product
16-Bit Multi-Function With A/D, D/A And Digital I/O Channels CPCI Cards
GX3232 Series
The GX3232 is a multi-channel 16-bit, analog input and output cPCI module, supporting 32 single-ended or 16 differential input channels and four analog output channels. The inputs can be software configured for differential or single-end operation and are sequentially scanned with a maximum aggregate scan rate of 300 kS/s. Three input ranges are software-selectable: ±10 V, ±5 V or ±2.5 V. Optionally, the GX3232 is available with a high voltage input configuration and supports three ranges: ±60 V, ±30 V and ±15 V. The high voltage configuration supports 16 single-ended or 8 differential input channels for high voltage and 16 single-ended or 8 differential inputs for low voltage measurement. Four analog output channels provide software-selectable output ranges of ±2.5 V, ±5 V or ±10 V. The outputs can be updated either synchronously or asynchronously and support waveform generation. Each output can be clocked at rates up to 300 kS/s. A 16-bit digital I/O port is also provided, which supports 16 bidirectional data lines. Note that when used with a TS-700 system only 8 of these digital I/O lines are available at the test system's receiver interface.
-
product
Cable
RCONQPMC-2
RCONQPMC-2 - Transitions from a SCSI-68 pin connector to four CJ70 Twinax, 3 lug, 1553 cable jack ends and one D-Sub 50 pin connector for additional I/O.
-
product
Extension Module
GE-DIO-42
Infinite Industrial Informatics Lt
GE-DIO-42 is a digital I/O, DIN rail mount expansion module with I2C serial communication interface. It can be used for the analog input expansion of Infinite's products as the SCOM-100 GSM controller and the iLOGPlus RTU/Data Logger.
-
product
Value-added Module With 4 BNC Video-in And 1 BNC Audio-in
VAM400
*4 BNC Video-in and 1 BNC Audio-in*Swappable modular design*Maximize I/O flexibility*Designed for tBOX300/500 series*EN 50155 and IEC 60945 certified; CE, LVD and FCC compliant
-
product
Servo
The Hardware: Drives, Motors, Cables (standard and robotics) – all seamlessly supported by Unitronics’ PLCs, HMIs, & VFDsThe Software:One integrated software for your complete motion application: PLC, HMI, Servo, VFD, and I/O
-
product
ATCA Rear Transition Module
ART132
The ART132 is an I/O expansion ATCA Rear Transition Module(ARTM) that provides PCIe, GbE, InfiniBand, USB andManagement I/O for the front blade. The module is designed tomate with Emerson front blades such as ATCA-7360 andATCA-7365.
-
product
Generator Protection Relay
SEL-700G
Schweitzer Engineering Laboratories, Inc.
The SEL-700G is the right solution for utility and industrial generator protection, with an autosynchronizer, flexible I/O, and advanced communications. Apply the SEL-700G for comprehensive primary and backup generator protection.
-
product
IC-PPC-VPX3d, 3U VPX QorIQ T2080 Single Board Computer
IC-PPC-VPX3d
The IC-PPC-VPX3d is a versatile 3U OpenVPX SBC for systems requiring high performance, low power and ample I/O. Based on the latest PowerPC QorIQ multiCore processor, it meets compute-intensive needs in industrial and harsh environments.
-
-
product
PXIe-7962, Virtex-5 SX50T FPGA, 512 MB DRAM PXI FPGA Module for FlexRIO
781206-01
Virtex-5 SX50T FPGA, 512 MB DRAM PXI FPGA Module for FlexRIO—The PXIe‑7962 provides flexible, customizable I/O for LabVIEW FPGA. It includes 132 single-ended I/O lines configurable as 66 differential pairs. You can pair the PXIe‑7962 with FlexRIO adapter modules that offer high-performance analog and digital I/O. Together, the two modules create a reconfigurable instrument that you can program with LabVIEW FPGA software. The PXIe‑7962 supports peer‑to‑peer streaming, which directly transfers data among multiple FPGA modules or select PXI Express modules without sending data to the host processor. With this feature, you can add FPGA capabilities to high-performance NI digitizers with NIST‑traceable calibration or expand your FPGA algorithms across multiple FPGAs for computationally demanding applications.
-
product
Count Down Test System
The Second Launch Pad Count Down system is implemented using VXI hardware designed by Data Patterns specific to the application requirements, featuring a redundant system handling upto 14000 I/O points.
-
product
Flight-Certifiable SBC
SBC314C
The SBC314C flight-certifiable single board computer is engineered in accordance with DO-178C and DO-254 and is available with supporting artifacts. It delivers great and proven performance thanks to the Power Architecture T2081 processor, and its diverse I/O set brings high functionality to the small form factor. The integrated XMC site allows even more connectivity, including high-density MIL-STD-1553 and ARINC 429 data bus communications as well as avionics discrete I/O through our RAR15CX flight-certifiable mezzanine.
-
product
Station Self-Service Controller
Advantech's Self-Service Controller ITA-1000 series supports Station Self-service System. As a rugged system with compact size, low power consumption, and fanless design, our controllers specialize in rich I/O with excellent maintainability.
-
product
48-Channel DIO (Digital Input/Output) PCMCIA Card
D480C
The D480C offers up to 48 separately controllable Digital I/O lines for general purpose control and monitoring applications.
-
product
Local Bus Master & Target Bridges
PCI 9052
The PCI 9052 PCI I/O Accelerator provides low cost connectivity for PCI slave designs. It is specifically targeted at easing the transition of existing ISA designs to the more feature rich and performance oriented PCI bus.
-
product
PCI Module
PCI-4SIP
The PCI-4SIP Module provides a Full PCI performance flexible I/O scheme, that supports industry standard Industry Packs. Choose from over a 100 different Industry Packs from Alphi Tech and others. For application requiring low cost, highdensity I/O or unique combinations, the PCI-4SIP is the perfect solution.
-
-
product
PXI-7954, Virtex-5 LX110 FPGA, 128 MB DRAM PXI FPGA Module for FlexRIO
780563-01
Virtex-5 LX110 FPGA, 128 MB DRAM PXI FPGA Module for FlexRIO—The PXI‑7954 provides flexible, customizable I/O for LabVIEW FPGA. It includes 132 single-ended I/O lines configurable as 66 differential pairs. You can pair the PXI‑7954 with FlexRIO adapter modules that offer high-performance analog and digital I/O. Together, the two modules create a reconfigurable instrument that you can program with LabVIEW FPGA software.
-
product
PIM Carrier Transition Module for 3U cPCI
TCP040-TM
The TCP040-TM is a 3U PIM Carrier Transition Module to be used with 3U CompactPCI PMC carrier like TEWS TCP270 or 3U CompactPCI modules with back I/O. It provides easy access to the PMC I/O lines of 3HE CompactPCI PMC carriers and most TEWS CompactPCI Modules with back I/O.
-
product
Protective Cover, G20x, Receiver, EMI
310113693
G20x offers the features of the G20 system, and adds an additional 8 modules in an extended tier for higher I/O needs. This solution uses 6.75" Series Pull-Thru Adapters.
