-
product
Multiprotocol PCI/104-Express Interface Board
8000PCIe104
The EXC-8000PCIe104 is a multiprotocol PCI/104-Express interface board for embedded applications or avionics test and simulation applications. Each board holds up to four independent modules and 10 discrete channels.
-
product
Co2 Meter Desktop with USB Interface Touch Screen
VAT810-TH/SD (VAT810-CO2)(VAT80
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Desktop:Touch buttons : CO2 monitor Real-time monitoring of indoor air quality including CO2,temperature ,humudity and VOC.
-
product
Interface and Isolation
Analog Devices offers a wide range of digital interface and digital isolators with iCoupler® technology covering the industry’s field bus and peripheral communications standards. Digital isolators, isolated transceivers, isolated A/D converters and isolated gate drivers utilize the award winning iCoupler® and isoPower® technologies for isolation solutions without many of the constraints found in optocouplers. Find design solutions for interface devices including keypad controllers, level translators, and high voltage protection products (channel protection, fault protection, overvoltage protection), and latch-up proof switches and multiplexers.
-
product
9 Pin Breakout Interface
VSI-Breakout-9
The VSI-Breakout-9 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
product
Ethernet Interface Module
Ethernet modules for RF Test Enclosures eliminate conducted and radiated interference while keeping data and power signals for the Ethernet link untouched.
-
product
Real Time Monitor Interface
ANALYSIS 4N
It supports a management on the on-site equipment, such as to add subnets, to add subnet equipment, or to config equipment parameters, etc. Subnet fulfills the following applications: parallel communication, interaction with equipment, batch logging, downloading, configuration, ending, timing synchronization and system status viewing.
-
product
Shared Memory Network PCI Express Interface
PCIe-SMN
Avionics Interface Technologies
2.125 Gbps Optical loop network - Single-mode and Multi-mode optical interfaces supported - Up to 256 Shared Memory Network nodes supported - Up to 200 MByte/sec sustained data rates - Maximum 500 nS latency between nodesNetwork interrupts supported - PCIe 2.0 (x4) CompliantSoftware Drivers available for Windows, Linux, LabVIEW Real-Time, and VxWorks
-
product
USB Interface
PK-232/USB
The PK-232/USB brickwall filters have tighter bandwidth and steeper skirts for improved noise and QRM rejection. New PK-232 firmware (Ver. 7.2) allows a wider selection of filters than the original PK-232, so the filter can match the mode. The correct DSP filter is automatically selected when you choose an internal mode. In RTTY, Timewave’s proven Twin Peak Filters pluck the mark and space tones from the noise and QRM for great copy. In PACTOR, the filter bandwidth automatically changes when the baud rate shifts in response to the error rate of the link. In Morse (CW), the operator can preset either 100 Hz or 200 Hz bandwidth. The PK-232/USB is compatible with all Windows W2K,XP,Vista/Win7 software terminal programs for the PK-232.
-
product
USB Controlled Loudspeaker & Microphone Test Interface
AmpConnect™ ISC
AmpConnect ISC is an all-in-one audio interface that simplifies your test setup and operation. It is a single, rugged, rack-mountable piece of hardware containing a high-accuracy audio interface, impedance box, amplifier, headphone amplifier, 2 microphone power supplies and digital I/O. It replaces multiple hardware devices, connecting to your computer via a single USB cable, and it is fully controlled by SoundCheck. This simplifies setup and calibration, eliminates cabling and reduces connectivity errors, as well as reducing overall system cost.
-
product
Linear Testfixture Testfixture for Mass Interconnect Cassette Interface Cassette and VPC ITA Frame Not Included, UUT 306 x 248 mm
MG-02-01 VPC G12
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 306 x 248 mm (wxd)• Outer dimensions: 470 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for Mass interconnect changeable cassette• Up to a maximum of 8 interface blocks of 160 or 170 signals• All interface blocks can be customized
-
product
Power Interface Board 3U, 2PSU connectors with AC pins
106PIBM302-9001R
The PIB 3U 2 slot has two power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
product
Precision DMM with RS232 Interface
HH2215
Resistance test up to 40MΩ. Wide Frequency test range from 10Hz to 300kHz. Capacitance measurement up to 100uF. Temperature test range from -4oF to 572oF to 300oC. Diode test audible continuity check and Transistor test
-
product
40 Gigabit Ethernet AdvancedTCA® Fabric Interface Switch Blade
aTCA-3710
The aTCA-3710 is a high performance, high bandwidth, 40G Fabric switch blade for AdvancedTCA® platforms. This product is ideal for bandwidth intensive telecom applications such as wireless access controller, DPI/security network, IPTV, IP multimedia subsystem, RNC/BSC, broadband access/bearer network, data center, and LTE/4G network applications. The aTCA-3710 provides 40GbE hub-to-node connectivity and integrated switch silicon that supports load balancing, priority queues, packet classification, and flow control to enable strict bandwidth management for implemented applications.
-
product
SIP-90-6 Test System Interface Probe
SIP-90-6
Overall Length (mil): 656Overall Length (mm): 16.66Rec. Mounting Hole Size (mil): 57Rec. Mounting Hole Size (mm): 1.45Recommended Drill Size: 1,45 mm
-
product
Linear Testfixture for VPC iCon i1 Mass Interconnected Cassette Interface (Cassette Not Included) 4 or 10 Positions Blocks, UTT 306 x 248 mm
MG-02-01
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 306 x 248 mm (wxd)• Outer dimensions: 470 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for Mass interconnect changeable cassette• Up to a maximum of 4 interface blocks of 160 signals• All interface blocks can be customized
-
product
Avionics Interfaces & Test Instruments
ARINC 664
Avionics Interface Technologies
AIT’s ARINC 664 test instruments can be used in test and simulation applications that are required to transmit and receive data over the ARINC 664 avionics databus. AIT’s instruments use small form-factor pluggable transceivers (SFP) and support copper or fiber optic physical network interfaces.Using an FPGA based architecture, with multiple embedded processors, the ARINC 664 instruments provide onboard support for upper layer protocol processing (A653, UDP, IP) and utilize DMA to provide optimal data throughput. All ARINC 664 protocol operations, including VL traffic shaping, redundancy management, and IP fragmentation and reassembly, are handled onboard.
-
product
Continuity Tester with Audible & Visual Indication
TEK404
The Martindale TEK404 is a low cost, easy to use continuity tester. It has audible and visual indication plus overvoltage protection. It has the same loud buzzer as the TEK402, giving a very clear signal of continuity.
-
product
Multi-channel Interface Module
PC104E-MA4
Alta Data Technologies’ PC104E-MA4 interface module is a multi-channel, multi-protocol 1553 and ARINC PCI/104-Express interface card supported by the latest software technologies. The PC104E-MA4 card is based on the industry’s most advanced 32-bit FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
product
Hall Sensor Board with I2C Interface
056-742
Version: +5V/60A +3,3V/60A +12V/90A -12V/5A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
product
Digital/Pattern/PE Card
PE16S
The PE16S represents a new level of performance and capabilities for PXI-based digital instrumentation. Based on the proven architecture of the PE16, the PE16S offers high performance pin electronics and an enhanced timing generator in a compact, 3U PXI form factor. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 256 bi-directional pins (16 boards). The PE16S offers 16 programmable level input or output channels with 2 PMU . The PE16S also supports deep pattern memory by offering 32 M of on-board vector memory with per channel dynamic direction control running test rates up to 66 MHz.
-
product
Quad Serial FPDP Interface with Virtex-6 FPGA - PCIe
Model 7811
Model 7811 is a member of the Cobalt® family of high performance XMC modules based on the Xilinx Virtex-6 FPGA. A multichannel, gigabit serial interface, it is idealfor interfacing to Serial FPDP data converter boards or as a chassis-to-chassis data link. The 7811 is fully compatible with the VITA 17.1 Serial FPDP specification. Its built-in data transfer features make it a complete turnkey solution. For users who require application-specific functions, the 7811 serves as a flexible platform for developing and deploying custom FPGA processing IP.
-
product
Reference Grade Expandable Production Interface
Atlas
Atlas and Titan are world class multi-track interfaces offering flexible expansion and unsurpassable sonic clarity. Using the latest generation of Prism Sounds trusted conversion, Atlas provides more preamps than Titan making it suitable for a wider range of recording scenarios.
-
product
USB Controlled High Precision Audio Test Interface
AudioConnect 4×4
AudioConnect 4×4 is a high accuracy 4-in, 4-out audio interface specifically audio test and measurement. It offers digital and analog audio in and out at any user-specified sampling rate up to 200kHz, and a high signal to noise ratio and wide frequency response, making it suitable for the most demanding measurement applications. Controls are simple – a single USB connection and a power indicator – all other typical soundcard controls that are not used for audio test applications have been eliminated to make operation and calibration simple with no room for error. AudioConnect 4×4 is supplied fully calibrated.
-
product
RS-232 to RS-422/RS-485 Interface Converter
Model 365
FEATURES: User Selectable RS-422 or RS-485; User Selectable 2 or 4 Wire RS-485; DataSpy® LCD Display; Intelligent Control of RS-485 Transmitter and Receiver; DTE/DCE Compatible; Data Rates Up to 115.2 KBPS. The Model 365 multimode interface converter allows operation in compliance with RS-485 or RS-422 equipment, and RS-232.
-
product
Hardware Debug Interface & Stand Alone Programmer
Cyclone PRO
P&E Microcomputer Systems' Cyclone PRO is an extremely flexible tool designed for in-circuit flash programming, debugging, and testing of Freescale HC08, HCS08, HC12, HC(S)12(X), and RS08 microcontrollers. Now featuring support for Freescale's ColdFire V1.
-
product
Conduction Cooled VPX Interface Board with PCI Express Host Interface
EXC-8000ccVPX
The EXC-8000ccVPX is part of the 8000 family of multiprotocol carrier boards. This conduction cooled VPX interface board has a PCI Express host interface and can support up to four independent removable modules and 10 on-board Discrete channels. Each removable module can be any of the 8000 family modules.The EXC-8000ccVPX supports Direct Memory Access (DMA), which enables the board to access system memory for reading and writing independently of the computer’s CPU. This results in faster data transfer to and from the board, with much less CPU overhead than when not using DMA.The EXC-8000ccVPX is supplied with C drivers, including source code. Mating connector provided for I/O connection.
-
product
PXI Chassis, Controllers, and Interface Modules
Build a PXI test system, by choosing the chassis and controllers that meet your needs. Keysight offers a variety of chassis with different sizes and performance characteristics.
-
product
Serial Data Acquisition And Control Interfaces
ICS's Serial to Data Acquisition and Control Interfaces are IEEE-488.2 compliant and and provide GPIB functionality over a serial link. Click on a link or scroll down to access the appropriate Serial Digital Interface:Our Serial to Data Acquisition and Control Interfaces have non-isolated analog and digital signals. Click here for our isolated Serial to Analog Interfaces.
-
product
DDS Function Generator, Digital Control 10MHz Or 20MHz, With/without USB/RS232 Interfaces
TG2000 Series
0.001Hz to 10MHz/20MHz frequency range6 digits or 1mHz resolution1ppm stability and 10ppm one year accuracyLow distortion, high spectral purity sine wavesInternal phase continuous sweep, lin or logAM, FSK, gated and tone switching modes5mV to 20V pk-pk from 50 or 600 OhmsStorage for multiple instrument set-upsUSB and RS232 Interfaces (TG2000 only)
-
product
Verifier Computer Interface Report
VCIR
The Verifier Computer Interface Report (VCIR) is a Windows software package that allows for transferring inspection report from your Inspector series bar code verifier to a computer. Once transferred you can review the ISO/ANSI inspection results or view the scan reflectance profile for detailed troubleshooting. The inspection results can be saved by job for later retrieval or to append new inspection results to the existing job. As each job is saved an Excel spreadsheet (CSV file) is generated. You can customize which parameters should be saved in the spreadsheet. The spreadsheet provides a simple report that will have a line for each bar code inspected.
