-
-
Product
Dust Test Chamber
-
Xi'an LIB Environmental Simulation Industry
Used to test the durability and sealing integrity of products (electronics, automotive parts, materials) against harsh, dusty conditions.
-
Product
Multi-Stage In-Circuit Test Fixtures
-
Circuit Check’s bi-level and multi-stage fixtures combine multiple test levels in a single fixture using controlled actuation and selected probe travels for powered and unpowered tests.
-
Product
Rapid Decompression Test Chambers
CA-RD(H)
-
CSZ's rapid decompression test chamber is designed to simulate rapid decompression for testing aircraft avionics. The environmental chamber meets the environmental conditions and test procedures for airborne equipment referenced in the RTCA DO-160 test specification. The DO-160 specification was designed to test sudden pressure changes starting from 8,000 feet to 60,000 feet (536 to 55 Torr) in 15 seconds. An altitude of 8,000 feet (536 Torr) was used for the initial cabin altitude and 60,000 feet was used for the final cabin altitude after decompression. This test specification is used to identify failures of materials inside of the cabin and the reaction to the surrounding environment.
-
Product
Large testing machine for timber
-
This device is used to conduct a three- / four-point bending test on wooden pillars. To facilitate the adjustment between the bearings, it is equipped with rails on the base as well as a trolley to transport the sample.
-
Product
Brick Power Module Test
-
Modern servers, workstations, and telecom equipment often use an Intermediate Bus Architecture (IBA) powered by isolated DC/DC converters known as "brick" modules. These brick converters step down the input voltage to a lower DC bus voltage, enabling designers to implement efficient, high-density, non-isolated Point-of-Load (POL) regulators that power components such as microprocessors, FPGAs, and ASICs on system boards. With smaller voltage step-down ratios now common, designing POL regulators has become more straightforward. Brick modules are so named for their standard physical formats (1/4 Brick, 1/2 Brick, Full Brick, etc.), making them easy to integrate and replace.
-
Product
Board Test Fixture Probes
-
Offering a wide range of standard spring contact probes to meet your testing requirements and has long been recognized as the world’s largest probe manufacturer. With over 60 different probe series ranging from 0.02" (0.51 mm) to 0.187" (4.75 mm) pitch with multiple length, travel, ICT, lead free and rotator options, we provide a full portfolio designed for general purpose test on bare boards, loaded printed circuit boards and surface mount assemblies.
-
Product
Exchangeable Test Fixture
2112/D/H/S-7/HG/Pylon
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 13,50 kg
-
Product
Test Contactor/WLCSP Probe Head
ACE
-
ACE™ test sockets offer optimal RF performance for fine pitch FBGA, QFN and wafer-level packages for Power Amplifiers, RF switches and mobile communications. Supporting pitches down to 0.4 mm, ACE features an innovative design that provides superior performance, improved yields and power efficiency.ACE probe heads deliver exceptional electrical performance, both DC and RF. Manufactured from HyperCore™ base material, a proprietary material of Cohu’s Everett Charles Technologies, ACE probes have the electrical properties of BeCu with the non-oxidizing properties of a precious metal. The short signal path, sharp tips, and large contact area between plungers provide high current conductance and reliable contact with less force.
-
Product
Buchholz Relay Test Benches
-
HAOMAI Electric Test Equipment Co., Ltd.
Buchholz relays are used to protect transformers, and these test benches perform necessary quality and performance checks.
-
Product
Compact Cable Test Van
ETL-8
-
Van-based cable test and fault location system ETL-8 is used for testing cable insulation and locating cable faults using a variety of methods.
-
Product
Environmental Testing
-
Environmental testing typically involves hot or cold temperatures, humidity, altitude (vacuum) or thermal shock. This testing can even be combined with other test methods such as vibration or shock.
-
Product
Portable Test Platform
FTB-4 Pro
-
The FTB-4 Pro is the latest addition to EXFO’s test orchestration portfolio which transforms business as usual into smarter, scalable network testing that significantly increases operational efficiency and provides vital insights into field operations, network performance and service delivery. The 4 slot modular FTB-4 Pro platform enables a unique combination for 100G commissioning, turn-up and troubleshooting which includes the FTBx-88200NGE 100G Multiservice tester (with iOptics transceiver validation software) and the FTB-5240S-P optical spectrum analyzer. There is no need to carry additional platforms or swap modules for unmatched transport and spectral testing on a single platform that no one in the industry can offer. The versatile FTB-4 Pro platform supports a wide range of modules for field testing, data center interconnect, submarine testing, and lab applications for maximum flexibility and ROI across all phases of the service delivery chain: development, deployment, maintenance and troubleshooting. Module combinations on the FTB-4 Pro can also include iOLM/OTDRs, market leading OLTS for fiber characterization, dispersion solutions and other transport modules all with compatibility with EXFO’s market leading fiber inspection probes.
-
Product
Magnet Testing
magtrack
-
The magtrack makes it possible to detect the absolute 3D position in space as well as the orientation of a magnetically marked particle over a course of time. The magtrack system is modular and can therefore be adapted to any installation and system.
-
Product
Wireless In-Circuit Test Fixtures
-
Higher density more complex circuit boards complicate testing requirements while smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in standard long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board or T-Board®. Circuit Check’s wireless fixture technologies reduce test program debug and maintenance times while easing the ECO process. Thus allowing for the higher level of test performance, the ability to probe smaller denser targets and achieve ultra-high node counts.
-
Product
Material Test Machines
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood Universal Test Machines, UTM, are widely use for different material testing, like semi-product & finished product made of rubber, plastic, metal, nylon, non-woven fabrics, textile, tape, polyfoam, waterproof materials, wire, cable, etc. With different test jigs or fixtures, the UTM can run the tensile, compression, shearing foce, adhesion, peeling force, tear strength, fatigue, etc test according to GB, CNS, ASTM, ISO, DIN, JIS, EN test standards.
-
Product
IEC61850 Relay Test Set
NF802
-
NF802 is full digital IEC61850 relay test set, equipped with 8 optical ports, and powerful data processing capability, can realize full digital IEC61850 protection relay testing.
-
Product
Extensive Qualification & Test
-
Quality and reliability of the battery pack design starts with proper cell selection. Ensuring the battery pack is well matched to the host equipment is often overlooked or not given sufficient priority until performance and/or supply problems occur. Proper cell selection is key and requires much more than checking dimensions and capacity. Designers need to consider loading, environment, shelf life, and a number of other factors specific to the application.
-
Product
Elcometer Bresle Test Patches
135C
-
The Elcometer 135C Bresle Test Patches determines the concentration of soluble salts on uncoated surfaces in accordance with the ISO 8502-6 test method.
-
Product
Automotive Testing Services
-
Ensure that your systems and components are compliant with SAE, OEM, E / e-Mark and other related national and international regulatory standards.
-
Product
PoE Transient Test Meter
Trans-Guard 910016
-
GrayStone Automation's innovative DCVBD voltage breakdown meter measures the breakdown voltage of many lightning protection devices and components to identify transient protection devices that may be damaged or defective and help prevent costly transient damage to critical and expensive equipment.
-
Product
VCORE Power Test
-
To support the heavy computing loads required by AI technologies, system servers must rely on high performance CPUs and GPUs capable of complex, real-time processing. These processors are powered by VCORE power supplies, embedded DC/DC converters, or voltage regulator modules (VRMs).
-
Product
Electronic Component Testing Services
-
New Jersey Micro Electronic Testing, Inc.
NJMET is proud to provide procurement and testing services to the commercial, military, aerospace, industrial automotive and medical industries. We also provide custom engineering consultation services. NJMET Inc. is AS9100/ISO9001:2008 certified and has recently successfully completed of The Defense Logistic Agency’s (DLA) laboratory suitability assessment and is qualified to test federal stock classes (FSC) 5961 (Semiconductor Devices) and FSC 5962 (Microcircuits) to DLA’s QTSL test requirements.
-
Product
Static Weathering Testing
-
Atlas Material Testing Solutions
Atlas' outdoor exposure sites provide a wide range static exposure testing for a variety of materials and end use conditions. Static (real-time) weathering testing capabilities include direct exposure using fixed or variable angle, backed or unbacked racks; indirect (under glass) exposure for interior materials; and black box exposure for paints and coating materials. Contact one of our qualified representatives to see which tests are right for you.
-
Product
Panel Test Solutions
-
C.C.P. Contact Probes Co., LTD.
CCP offers special rounded pins and test modules for panel testing.
-
Product
Multifunction Substation Test Set
STS 5000
-
STS 5000 is a multifunction substation maintenance & commissioning test system for current, voltage and power transformers designed to perform primary tests requested in substations commissioning. It allows to perform accurate tests on CTs, VTs, PTs and ground grid.
-
-
Product
Brake Test Systems
Giant 8000 Series
-
Customer perception of vehicle quality is closely related to the NVH behaviour of the vehicle. With the HORIBA ATS Brake testing system, NVH relevant design features are analyzed and various metrics stored in the database of the automation system. For friction borne vehicle NVH problems coming from the brake and its components the GIANT 8000 Series is the ideal tool to resolve it. The GIANT 8000 Series is superior NVH test system providing you with the best testing conditions for all types of vehicles. Test brake fixtures could be tested with a complete wheel suspension system. In a semi acoustic chamber NVH tests could be realized and drum brakes and disc brakes including the vehicle axle could be tested.
-
Product
Compatibility Testing
-
Cross-Browser Testing Ensures equal user visual experience Provides identical functional behavior of applications Cross-Platform Testing Ensures flawless product processing under different OS types, versions and locales Confirms seamless application functioning
-
Product
Eddy Current Test System
CIRCOGRAPH® Product Family
-
Foerster Instruments, Incorporated
The CIRCOGRAPH eddy current test system with rotating probes guarantees maximum detection sensitivity for exposed longitudinal surface defects on bright material. The test system is primarily used for wire drawing machines, Cu tube rewinders, and finishing sections in the bright steel sector. The individually tailored test systems by FOERSTER can be fitted with rotating sensors or CIRCOSCAN rotating discs. They scan flat and profiled material, e.g. when testing rails and billets.
