-
product
L31 Series Heavy Duty Vertical Multi-Station Stainless Steel Liquid Level Switch
L31
As many as six level control points and up to 72” in overall length. Mount at the top or bottom of a tank. It can be fully customized. Typically found in potable water, hot water, acids, and various solvent applications.
-
product
PXI/PXIe RF Switch, Dual SPDT, Terminated, 8GHz, 50Ω, SMA
42-880B-001
The 40-880B-001 (PXI) and 42-880B-001 (PXIe) are dual SPDT 50Ω RF switches with 8GHz bandwidth. The 40/42-880B range has automatic termination of unused signals and are available as a dual switch in 1 slot, a quad switch in a two slots or hex and octal switches in three slots.
-
product
LXI Matrix Switching Unit
ProDAQ 6140
The ProDAQ 6140 provides a relay matrix which can be fitted between the sensors and actuators on a device under test and the data acquisition and control system. It allows to separately connect/disconnect the signals from either side and to connect them to an internal bus. In this way signals can be routed via the bus to new destinations or the bus can be used to monitor or supply test signals. This allows calibrating and debugging the system without disconnecting and separating channels throughout the system wiring.
-
product
8x8 HDMI Matrix Switch with RS232 and IP Control
HSM-I-08-08
The HSM-I-08-08 is a powerful 8x8 HDMI matrix switch with RS232 and IP control (internal web-server and Telnet). The unit supports HDCP, deep color, multi-channel digital audio (up to 7.1 channels), and may be used with any combination of DVI (PC) or HDMI (HDTV) sources and displays.
-
product
0 Hz/DC to 14 GHz, Single-Pole, Four-Throw MEMS Switch With Integrated Driver
ADGM1304
The ADGM1304 is a wideband, single-pole, four-throw (SP4T) switch, fabricated using Analog Devices, Inc., microelectro-mechanical system (MEMS) switch technology. This technology enables a small, wide bandwidth, highly linear, low insertion loss switch that is operational down to 0 Hz/dc, making it an ideal switching solution for a wide range of RF applications. An integrated control chip generates the high voltage necessary to electrostatically actuate the switch via a complementary metal-oxide semiconductor (CMOS)-/low voltage transistor-transistor logic (LVTTL)-compatible parallel interface. All four switches are independently controllable. The ADGM1304 is packaged in a 24-lead, 5 mm × 4 mm × 0.95 mm lead frame chip-scale package (LFCSP).
-
product
Force Sensors, Controls & Switches
Direct caliper motor/spindle integration for Brake by Wire systemsExtra-small form factor MSG sensors that weigh less than five gramsFacilitating system-level miniaturizationAdvanced button-type sensors designed to lower costs and improve accuracy
-
product
Receiver, G2, 2 Module, Keying Feature, With Protective Cover, With Micro Switch
310120112
Receiver, G2, 2 Module, Keying Feature, with Protective Cover, with Micro Switch
-
product
High Accuracy Low Pressure Environment Pressure Switch
P100G
The P100G High Accuracy Low Pressure Environment Pressure switches are ideal in light pressure applications where precision of setpoint must be high and repeatability low. These switches are commonly used in natural gas well heads, natural gas generator sets, and air applications like forced draft blowers. The P100G can be used both in dry indoor applications or within an enclosure.
-
product
Crossing Control Bypass Switch
XCBS-DL
The XCBS-DL is permanently wired into each crossing warning system, and can be configured with either a removable or non-removable bypass key. Simply connect the track connection harness to the designated track connection terminals. To prevent unnecessary operation of the crossing warning system, insert the key and select "bypass", rotate the knife switch to "bypass" and the crossing is disabled. When in the "bypass" position, a Dummy Track Load is connected to the track wire connections in parallel with the rails and the crossing approaches are shorted, preventing unnecessary activation when track equipment is working in the crossing approach circuit. The opening of one track lead may be desired to prevent unnecessary activation with intermittent shunting on the crossing approaches close to the crossing.
-
product
PXI/PXIe RF Switch, Triple SPDT, 3GHz, 75Ω, SMB
42-830A-003
The 40-830A-003 (PXI) and 42-830A-003 (PXIe) are 75Ω RF switches with 3 separate SPDT relays in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks have been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
product
PXIe 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
42-205-008
The 42-205-008 (PXIe) is an 8-channel fault insertion switch designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. It is available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
product
PXI Single 2 x 2 Fibre Optic (M Mode) SC M50
40-860-212-M50
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
Optical Switch
FTBx-9150
With crosstalk of –80 dB and life expectancy of 10 million cycles, the FTBx-9150 Optical Switch is ideal for bidirectional component testing, ribbon fiber testing, multichannel monitoring, remote and multiple-component testing, signal routing and bypass switching. Housed in the LTB-8-based test systems, the FTBx-9150 provides highly accurate and repeatable fiber-to-fiber switching. It offers a choice of 1x2, 1x4, 1x8, 1x12, 1x16, 1x24, 1x32, 2x2 and 2x4 configurations. Designed for minimal reflectance, the switches integrate precision optical components into a compact modular package. Both singlemode and multimode versions are available and offer a solution for all your optical switching needs.
-
product
Compound Switches
P100C
The P100C High Accuracy Compound Switches are ideal in applications where precision of setpoint must be high and repeatability low. The P100C is highly versatile with the ability to operate in positive and negative pressure environments. These switches can be used both in dry indoor applications or within an enclosure.
-
product
PXI Single Bus 32-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-501
The Single Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
Single Bus 36-Channel 2A PCI Fault Insertion Switch
50-190-201
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
Coaxial Switch, DC to 20 GHz, SPDT
8765B
The Keysight 8765B offers excellent electrical and mechanical performance with broadband operation, high isolation, low SWR, long life, and exceptional repeatability.
-
product
PXI 16-Channel 4-Bus 2A Fault Insertion Switch
40-197A-002
This 16-channel fault insertion switch is primarily intended for routing simulated fault conditions in automotive and aerospace applications involving the reliability testing of safety critical controllers.
-
product
Floating Contact Null Switch
1640
The unique electric switch design in the 1640 is another Dwyer Instrument, Inc. innovation. The Dwyer Model 1640 Differential Pressure Switch resembles the Series 1630 switches. The Model 1640, however, is equipped with a single pole, double throw floating contact switch (not snap acting) so it functions as a null switch.
-
product
Rugged Gig-E Switch
RESIU31
NAI's RESIU31 subsystem is configured with NAI's 75D4-H2, a Layer 2+ Gigabit Ethernet Switch built upon NAI's multifunction, 3U cPCI board technology. Ideally suited for rugged military, industrial, and commercial applications, the RESIU31 delivers an off-the-shelf Ethernet switching solution that accelerates deployment of SWaP-optimized systems.
-
product
HDMI Matrix Switch Over HDBase-T with Power Over Ethernet (PoE)
SM-8X8-C6HDR-POE-HDBT
The VEEMUX® HDMI Matrix Switch Over HDBase-T with Power Over Ethernet routes and distributes uncompressed HD 1080p, multi-channel audio, Ethernet, and IR from eight HDMI video sources to eight displays via inexpensive CAT6a/7 cable using HDBase-T technology. Power over Ethernet provides power to receivers that can be located up to 328 feet away.
-
product
Switch Analyser
SA10A
It has a built-in micro Ohm meter/Ductor for measuring of static and dynamic resistance of the breaker poles. It only weighs 11,6 kg. The versatility and precision that this unit offers is, without question unchallenged, and it will indeed be your best partner when testing circuit breakers. Tests in areas with high induction at known problematic substations has proven the SA10A to be the only circuit breaker timer that could withstand these extreme conditions. It's rugged, it's small and highly appreciated by our customers.
-
product
PXI Solid-State Switch Module, 6xSPST, 1.5 A, 400 V, Hardware Interlock
40-185A-001-HI
The 40-185A-001-HI has 6-off high current SPST switches with hardware interlock in two PXI slots and is part of our range of high power solid state switching solutions.
-
product
PXI Optical Switching
Pickering's range of PXI optical switching modules include high performance multiplexers and insert/bypass switches. MEMS (Micro Electro-Mechanical Systems) switch technology offers higher performance and longer operational life compared to conventional prism based optical switching
-
product
RF Switch Modules
Analog Devices RF switch modules include the highest bandwidth switch modules. SPST, SPDT, SP4T, SP6T, and SP8T versions (reflective and absorptive) are available for a wide range of power (up to 27 dBm) applications, including antenna switching, filter switching, and tuner applications.
-
product
E & W-Band PIN Diode Waveguide Switches
Fairview Microwave’s single-pole single-throw (SPST) and double-pole double-throw (DPDT) PIN diode waveguide switches feature fully integrated WR-10 and WR-12 waveguide ports and cover popular E-band (60 to 90 GHz) and W-band (75 to 110 GHz) frequencies. Switch circuits integrate low loss Fin-line assemblies with high performance GaAs beam-lead diodes that results in 4 dB insertion loss, greater than 25 dB of Isolation and fast switching speed < 300 nsec.
-
product
VPX Switches & Routers
Curtiss-Wright Defense Solutions
Our OpenVPX switches and routers, some with SOSA-aligned options, provide systems integrators with a fast and powerful way to interconnect chassis, cards, and processors through switched Gigabit, 10 Gigabit, and 40 Gigabit Ethernet interfaces.
-
product
Belt Alignment Sensors And Misalignment Switches
Electro-sensors belt alignment sensors are mounted along the conveyor belt that needs to be monitored for misalignment. The rub block assemblies are mounted so that the brass surface area is in-line with the edge of the conveyor belt. When the belt wanders it then rubs up against the brass block. The contact with the belt creates friction and heat that the sensor in the brass block records as a rise in temperature.
-
product
2X16 PXIe Switch Matrix, 300 KHz to 18 GHz
M9164C
M9164C 2X16 PXIe switch matrix, 300 KHz to 18 GHz is a full cross-bar switch matrix that provide a switch based multiport VNA solution.
-
product
Test Switches
Series RT
Up to three Series FT switches can beassembled on various size 19" wide panels. One piece clear cover standardPanels available in choice of colors and materials
