-
Product
Power Amplifier
5241
-
The Model 5241 is a voltage-controlled power amplifier designed exclusively for Magtrol's Model HD-825 Hysteresis Dynamometer. Because of its double braking system, the HD-825 requires more than 4 amps of power in order to reach full torque. The 5241 (which can provide up to 5 amps of output current) is necessary in order to amplify the power between a 6200 or DSP6001 Controller (which both have a maximum current output of 1 amp) and the HD-825 Dynamometer.
-
Product
A/D - D/A Converters
-
ST's high performance converters combine high-speed with ultra-low power consumption by using 0.25µm and 130nm high-end proven technology in high volume.
-
-
Product
ATE System Power Supply, 300 V, 5 A, 1500 W
N5771A
Power Supply
The single output, 1500W N5771A provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current.
-
Product
Power Supplies
ZPS-1600B
-
80Plus Silver Certified provides typical 88% efficiency at 50% of max load. The ZPS-1600B can give you the power you need at higher efficiency, which means you can use the same power with less energy. Built in 16 8-pin PCI-Express graphic card connector offering further upgradability.
-
Product
Power Supplies
CU-400B
-
The CU-series is a semi-modular power supply that lets you select the cables you need while powering your system at a healthy voltage. Everyone likes a clean and easy installation. This power supply allows you to keep what you want and remove what you don't. While necessary connectors, like the 20+4 pin power connector, are attached to the unit, you decide which of the others should stay. Customize your power supply to reflect your system.
-
Product
Current Source-Sink D/A Converters
-
Analog Devices’ current source D/A converters (DACs) portfolio is ideal for photonics control applications where low current noise density, low dropout voltage, and high power efficiency, in addition to high channel density, is critical to system performance. The flexibility of the configurable current source D/A converter outputs, and 300 mA current delivery, make them suitable for resistive heaters and proportional solenoid drive.
-
Product
DC/DC Converter 1000 W
CRS-1000-6478-C
-
DC/DC converter with 1000 W from Premium | input ranges 28.8 - 60 VDC | output 24 V | operates in temperatures from -25 to +70 °C | designed according to EN50155
-
Product
Power Potentiostat/Galvanostat
1100C
-
The Model 1100B series power potentiostat/galvanostat is designed for electrochemical applications that require relatively large current and high compliance voltage, such as battery studies, corrosion, electrolysis, and electroplating. The current range is 2 A, and the compliance voltage is 25 V. The instrument contains a high speed digital function generator, a fast data acquisition system, filters for current signals, iR compensation circuitry, a potentiostat, and a galvanostat (Model 1140B). The potential control range is 10 V.
-
Product
Power Supplies
-
A power supply is a component that supplies power to at least one electric load. Typically, it converts one type of electrical power to another, but it may also convert a a different form of energy - such as solar, mechanical, or chemical - into electrical energy. A power supply provides components with electric power.
-
Product
Power Supplies
CU - SERIES
-
The CU-series is a semi-modular power supply that lets you select the cables you need while powering your system at a healthy voltage. Everyone likes a clean and easy installation. This power supply allows you to keep what you want and remove what you don't. While necessary connectors, like the 20+4 pin power connector, are attached to the unit, you decide which of the others should stay. Customize your power supply to reflect your system.
-
Product
Power Meters
-
The Krytar Model 9000B is a low cost, high performance CW power meter using a diode based power sensor. The power meter can measure power levels from -39 to +20 dBm and cover frequencies from 100 kHz to 40 GHz. With bench and field service applications in mind, the power meter was designed to be completely portable. The power meter can be used for swept measurement.
-
Product
- RS-485 to Fiber Optic Converter
Model 276A
-
FEATURES: Data Rate to 1 MBPS; ST Connectors; DB-25 Connector; Half-duplex operation; Extends distance of RS-485 network to 6,600 ft (2 km) on multimode fiber cable. The Model 276A provides the capability of transmitting an RS-485 signal via a fiber optic link.
-
Product
Power Analyzer
-
Manufacturer of a wide range of products which include Harmonic Single Phase Energy Analyzer and Single Phase Distortion Power Meter Analyzers.
-
-
Product
Power Supplies
CM-300
-
The CM-300 is perfect for those with smaller computer cases tiny in size, but huge in effectiveness with an anti-corrosive nickel plated chassis. Within this power supply is an 80mm silent cooling fan designed to cool at maximum efficiency with the lowest noise level. And to power your CPU, the CM-300 comes with an 8 pin Xeon connector ready in a tube-tide design to keep all your wires tidy. The CM-300 is the ideal combination of power efficiency in a sleek body kit.
-
Product
Optical Path Converter
LS512A/LS512B
-
There are many LED manufactories using two integrating spheres and one spectrophotometer to do test. The previous testing way is: when you use big sphere to test, the customer need to connect the detector cable and optical fiber from the Spectrophotometer to the big sphere, after the calibrating and then you can do the test. When you use the small sphere, you need to take away the detector cable and optical fiber from the big sphere to the small sphere, then need to calibrate again. It is too troublesome to take out the detector cable and optical fiber between the big sphere and small sphere, and you need to calibrate again for every change. The frequent change will also shorten the life of the detector cable and optical fiber.
-
-
Product
Adapter to Convert (mini-PCI) mPCI
PMC2mPCI
-
Install wireless and other mPCI devices into PMC environments. PMC2mPCI adapts the PMC form factor to mini-PCI type III. PMC2mPCI installs into a standard PMC position - 32 bit PCI bus connectors, standard power and ground, standard standoffs and blank bezel.
-
Product
RF Converters
-
Typically designed for radar or wideband EMC test applications, our frequency converter modules are designed for the conversion between complex baseband waveforms and higher transmitted frequencies. These modules are ideal for integration with digitising modules.
-
Product
Power Supplies
ZPG-1000B
-
80Plus Gold Certified provides typical 87% efficiency at 50% of max load. The ZPG series can give you the power you need at higher efficiency, which means you can use the same power with less energy. Built in QUAD 8-pin PCI-Express graphic card connector offering further upgradability.
-
Product
Voltage Converters
-
Made from marine-grade aluminium extrusions or heavy-gauge aluminium sheet metal. Powder-coated or anodized, and use stainless fittings throughout Fitted with robust circuit boards using expensive heavy-gauge copper conductors, designed by Analytic Systems' engineers and assembled in our plant.Models are available to step-up, step-down, stabilize or isolate DC power over a range of 12 to 360 volts. No matter which unit you need, these easy-to-install Voltage Converters will give you many years of reliability.
-
-
Product
Power Supplies
CU-series
-
The CU-series is a semi-modular power supply that lets you select the cables you need while powering your system at a healthy voltage. Everyone likes a clean and easy installation. This power supply allows you to keep what you want and remove what you don't. While necessary connectors, like the 20+4 pin power connector, are attached to the unit, you decide which of the others should stay. Customize your power supply to reflect your system.
-
Product
IRIG B to NTP/SNTP Converter
-
Signals & Systems India Private Limited
IRIG B TO NTP/SNTP CONVERTER – SPC-INS-1010 is a compact DIN rail mountable protocol converter unit which synchronizes and maintains the timing and frequency requirement of power and process industry equipment using IRIG-B signal obtained from GPS receiver. It provides nanosecond accuracy when external time references are not available. It has the storage facility to store the system log file. It delivers NTP, SNTP, PFC-Pulse, RS232 & RS485 outputs. The system enables configuration and monitoring through Web-based application. It supports a wide range of power supply input either 90V-260V AC/DC or 18-36VDC or 36V-72VDC.
-
Product
VME 16-channel Differential to Single-Ended Signal Converter
V1250
-
The V1250 is a 16 channel differential to single ended signal converter in a 1-unit wide VME 6U form factor. It provides differential inputs (34-pin 2.54 mm header, Zdiff = 100 Ω) and single ended outputs (coaxial LEMO, Rout = 50 Ω).
-
-
Product
Programmable Linear DC Power Supply 3 Outputs, 0-60V/0-3A/1.8V/2.5V/3.3V/5V;5A
T3PS60033P
DC Power Supply
Programmable Linear DC Power Supply 3 Outputs, 0-60V/0-3A/1.8V/2.5V/3.3V/5V;5A.
-
Product
Power Networks Test
TX6000
-
The TX6000 is a hand held Time Domain Reflectometer with 11 range scales covering the range 0-6000 meters, with a 7 mater first range scale and a 0.5 meter dead zone near and far end faults are clearly displayed on its 128×64 pixel back light Liquid Crystal Display.
-
Product
Programmable Power Supplies
GENESYS+™ Series
-
Utilizing embedded microprocessor technology to provide advanced performance and functionality, the GENESYS+™ series has the highest power density and lightest weight available for its size with a comprehensive set of user-friendly interfaces.
