-
product
PXI/PXIe Microwave Transfer Switch, Dual, 40GHz, 50Ω, SMA-2.9
40-782B-542
The 40-782B-542 (PXI) and 42-782B-542 (PXIe) dual transfer switches are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50Ω and a maximum operating frequency of 40GHz. Connections are made via front panel mounted high quality SMA-2.9 coaxial connectors.
-
product
PXI Dual 2 x 2 Fibre Optic (M Mode) ST M50
40-860-522-M50
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
Automated Optical Switch - PXI
Add optical switching capability to your test system with Quantifi Photonics’ automated optical switches. The fast and reliable optical switch will enable automated sequential testing, saving time and streamlining your test procedures.
-
product
PXI Source Switching Module
40-618A-001
The 40-618A PXI Source Switching Module consists of 12 separate 4-channel multiplexers and 44 uncommitted SPST relay contacts in a single width PXI module.
-
product
PXI/PXIe RF Switch, Hex SPDT, 3GHz, 50Ω, MCX
42-870A-106
The 40-870A-106 (PXI) and 42-870A-106 (PXIe) are 50Ω RF switches with 6 separate SPDT relays in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz.
-
product
PXI 4 x Changeover Switch 2.5GHz, 50 SMB
40-710-514
This RF switching card has a bank of four individual high performance RF changeover switches (50 or 75 Ohm, Bi-directional) with very low insertion loss, suitable for handling signals up to 2.5GHz. Applications include aerial switching, routing high frequency signals into oscilloscopes and analyzers.
-
product
8-Sites ISP & I2C/SPI Interface
YAV90ISP
Industrial Programmers Interface up to 8 targetsRelay BarrierDemultiplexer module up to 32 devicesCommunication Interfaces I2C and SPI
-
product
Modular VXI Switch Card Carrier
1260-100
The 1260-100 Switch Carrier accommodates up to six plug-in switch cards, providing optimum switching solutions while reducing the ATE size requirements.
-
product
Standard 2.90 (82.20) - 5.40 (153.00) Switch Probe
TSP157-F200-1
Current Rating (Amps): 10Average DC Resistance lower than (mOhm): 20Test Center (mil): 157Test Center (mm): 3.99Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 984Overall Length (mm): 25.00Switch Point (mil): 67Switch Point (mm): 1.70
-
product
PXI Dual 2 x 2 Fibre Optic (M Mode) SC M50
40-860-222-M50
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
Alternate 1.10 (31.18) - 7.20 (204.00) Switch Probe
TSP100-F180-2
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
product
PXI Solid State Switch Module, 3xSPST, 10 A
40-182A-012
The 40-182A-012 has 3 off high current SPST switches in one PXI slot and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 10A of continuous current and switch up to 200V signals. The switch can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
PXI Solid State Switch Module, 3xSPST, 10 A, Hardware Interlock
40-182A-012-HI
The 40-182A-012-HI has 3 off high current SPST switches with hardware interlock in one PXI slot and is part of our range of high power solid state switching solutions.
-
product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass, Single-Mode, 9/125 Fiber, LC Connectors
42-860A-422
The 40/42-860A-422 is a PXI/PXIe dual insert/bypass switch with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
product
PXI/PXIe MEMS Optical Switch, Triple Insert/Bypass
40-860A-432
The 40/42-860A-432 is a PXI/PXIe triple insert/bypass switch with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
1x13 Optical Switch
N7734A
The N7734A is a 1x13 fiberoptic switch, available for single-mode or multimode fiber connections. These enhance accurate measurements and ease automation with excellent repeatability, fast switching time and flexible interfacing with LAN, USB and GPIB.
-
product
Switch PXI Solid-State Switch Module, 6xSPST, 25 A, 100 V
40-184A-001
The 40-184A-001 has 6-off high current SPST switches in two PXI slots and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid-state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
product
Standard 1.10 (31.18) - 4.80 (136.00) Switch Probe
TSP100-C100-1
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
product
PXI Single Microwave Transfer Switch 18GHz 50 SMA
40-782A-521
The 40-782A-521 is a single transfer switch and is part of our range of PXI microwave switching modules. It has a characteristic impedance of 50Ω and a maximum operating frequency of 18GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
product
MSP Switch Probes
Switch point flexibilityDesigned for long life and reliable performanceVariety of tip options
-
product
PXI Dual 2 x 2 Fibre Optic (M Mode) STM62.5
40-860-522-M62.5
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
PXI/PXIe Microwave Transfer Switch, Dual, 18 GHz, 50 Ω, SMA, Failsafe, Remote Mount
42-782B-522-E
The 40-782B-522-E (PXI) and 42-782B-522-E (PXIe) dual failsafe transfer switches with remotely mounted relays are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 18 GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
product
PXI Dual 2 Channel (M Mode) SC 62.5 Cons
40-855-222-M62.5
The fiber optic switches connect the common to a channelby redirecting the optical signal into a selected output fiber.This is achieved using Micro-Mechanical Mirrors driven bya highly precise mechanism and activated via an electricalcontrol signal.
-
product
PXI/PXIe RF Switch, Triple SPDT, 3GHz, 50Ω, MCX
42-870A-103
The 40-870A-103 (PXI) and 42-870A-103 (PXIe) are 50Ω RF switches with 3 separate SPDT relays in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
product
PXI/PXIe MEMS Optical Switch, Triple Insert/Bypass, Single-Mode, 9/125 Fiber, MU Connectors, With Interlock
42-860A-332-HI
The 40/42-860A-332-HI is a PXI/PXIe triple insert/bypass switch with MU connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
product
PXI Multiplexer Switch Module
PXI Multiplexer Switch Modules are ideal for high-channel-count applications that need to connect measurement or signal generation instruments to various test points on devices or units under test(DUTs or UUTs). PXI Multiplexer Switch Modules use a variety of relay types, including electromechanical armature relays, reed relays, field-effect transistor(FET) relays, and solid-state relays, each with their own benefits, allowing you to choose a multiplexer that fits your requirements. To program the switches, you can use the IVI-compliant NI-SWITCH driver software, complete with help documentation, example programs, and a soft front panel application for interactive control of switches. For intelligent management of complex switch systems, NISwitch Executive provides additional software tools to help you design, build, and deploy your switching system.
-
product
PXI Hex SPDT RF Switch, 8GHz 50Ω SMA, Terminated
40-880A-003
The 40-880A-003 is a hex SPDT 50Ω RF switch with 8GHz bandwidth. The 40-880A range of SPDT switches have automatic termination of unused signals and are available as a dual switch in a 1 slot PXI module, a quad switch in a two slot PXI module or hex and octal switches in three slot PXI modules
-
product
PXI/PXIe Microwave Transfer Switch, Single, 40 GHz, 50 Ω, SMA-2.9, Failsafe
42-782B-541
The 40-782B-541 (PXI) and 42-782B-541 (PXIe) single failsafe transfer switches are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 40 GHz. Connections are made via front panel mounted high quality SMA-2.9 coaxial connectors.
-
product
High Density, 64-Channel Switch Card - 64 Channel, SPDT, High Isolation, Low Crosstalk Switch Module
1260-16A
The Astronics 1260-16A is a 64-channel, SPDT, high isolation; low crosstalk switch module designed for switching and routing sources such as AC and DC power supplies in automated test systems. The 1260-16A switches currents up to 6A, AC or DC, and voltages up to 110VDC or 250VAC.
-
product
PXI Fault Insertion Switch, 7-Channel, Two Fault Buses, 20 A
40-194A-002
The 40-194A-002 is a 7-Channel Fault Insertion switch with two fault buses, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
