-
Product
64-Channel VME Relay Module
V210
-
The V210 is a single-wide, 6U VME module that includes 64 SPDT relays and drivers. User-settable DIP switches set the A16/A24 VME address mode, VME address, and select whether the relays are statically operated or operate in latching mode, where relay states are sustained when VME crate power is off.
-
Product
Circuit Breaker Analyzer
CBA 3000
-
CBA 3000 allows any timing test, motion and speed analysis, multiple contemporary static and dynamic contact resistance measurements, both sides grounded (BSG) tests, undervoltage condition test and more. All these functions are integrated in a single lightweight test case without the need of connecting additional external modules.
-
Product
Manual Screw Flat Grips
-
Screw flat grips are general-purpose grips used for static tensile testing of a wide range of materials, most commonly, rubbers, plastics, textiles, and paper, and specimens such as plates and wires. Another advantage of these grips is they can be used to test thick specimens, up to 16 mm (0.63 in).
-
Product
ST/MT Family
-
MT System is a configurable test equipment suitable to verify static and dynamic parameters of power semiconductors (i.e. IGBT, MOSFET, DIODE, THYRISTOR, SiC, GaN, etc) packaged and unpackaged (discrete, module and substrate). ST System is a test equipment suitable to verify stability or drift of all static parameters of discrete power semiconductors.
-
Product
Gauss Meters
-
A gauss meter displays electromagnetic wave measurements in Gauss (G), milliGauss (mG), milliTesla (mT) or microTesla (µT) units. A gauss meter can detect either static (DC) permanent (rare-earth) magnetic or dynamic (AC) electromagnetic fields (EMFs), or both. Thus, it is important to review the specifications of a gauss meter prior to purchase to ensure suitability for the intended application.Neodymium (NdFeB) permanent magnets are among the world's strongest and most widely used magnets. When testing magnets made of neodymium or other rare-earth elements, a gaussmeter or magnetometer capable of measuring DC magnetic fields is required. However, most electromagnetic fields encountered are generated by AC currents. Examples include electrical power lines, transformers and wiring for overhead lighting, solar panels and other electrical devices and equipment. Electromagnetic fields from electrical installations are believed to cause feelings of nervousness, anxiety and paranoia in EMF-sensitive human beings.Most gaussmeters offered by PCE Instruments can be calibrated and certified according to DIN ISO 9000 standards for an additional fee. Replacement gaussmeter probes and optional accessories are available for most gaussmeter models.
-
Product
Gravimetric Gas/Vapor sorption vacuum analyzer
DVS Vacuum
-
The DVS Vacuum is designed for single and multicomponent vapor/gas sorption analysis, supporting static and dynamic experiments. The system’s key features are precise control and measure of temperature and pressure while recording the changes in sample mass using high-resolution UltraBalance.
-
Product
Universal Testing Systems (Up to 600 kN)
5980 Series
-
Instron 5980 Series floor model testing systems are universal, static testing systems that perform tensile and compression testing; and also perform shear, flexure, peel, tear, cyclic, and bend tests. The 5900 Series are engineered for precision, built for durability, and offer the flexibility for changing requirements. They are designed with standard and optional features that increase testing efficiency and improve the testing experience for the operator. 5980 Series floor models are robust, heavy-duty frames commonly used for testing high-strength metals and alloys, advanced composites, aerospace and automotive structures, bolts, fasteners, and plate steels. Frames are available in load capacities of 400 and 600 kN.
-
Product
CPCI Based 486DX4 Board
MS 1501
-
- CPCI/PXI Bus Interface, 6U form factor- Watchdog Timer- Hot Swap Facility- PCI Bus Rear IO Expansion for External Bus Interface- Debugging Monitor interface through RS232- JTAG interface for 486 for boundary scan test- Power Source through the CPCI connector J1 (±12V, +5V, 3.3V)- 1Mbytes of Dual Port RAM, 256Kbytes of STATIC RAM- 1MBytes of FLASH PROM- RS232, RS422 Serial Interface- Intel 486DX4 operating at 100MHz frequency at the core- Driver interface for Windows2000/XP/VISTA and LINUX/RT LINUX OS
-
Product
Test Line • Equipment For Testing For Function
-
The test equipment is used for qualitative functional testing of discharge power supply units and / or ionization units from the static line and air line (discharge). The devices are usually operated with a single button and indicate via LED, whether the device under review functions properly.
-
Product
(2500kN+) Fatigue Testing Systems
8806
-
The precision mechanical systems, combined with the advanced features of the 8800 digital controller and Dynacell™ load cells, enable Instron to supply fully-integrated turnkey solutions to meet the most demanding applications. The system can be used to cover a broad range of static and dynamic test applications, covering metals, rebar, high-force fracture mechanics, aerospace panels, civil engineering components, wire ropes, or concrete.
-
Product
ResMap or DualMap Manual Load
-
Creative Design Engineering, Inc.
*Type: Table Top*Wafer load: Manual *Wafer size: 2" to 8", 152mm x 152mm*Mini Environment: N/A*Probe Changer: N/A*Aligner: N/A*Size: 12" x 19" x 10"*Range: 1m/ to 10M/*Accuracy: 0.5%*Repeatability: 0.02% *Static Repeatability: 0.1% dynamic
-
Product
Burn-In Test
-
Trio-Tech provides a comprehensive range of semiconductor testing services through its state-of-the-art laboratories in the Far East. The laboratories provides static and dynamic Burn-in /HTOL /SLT testing and other testing services. All of the company’s testing facilities are ISO9001, ISO14000, ISO17025 and DSCC certified ensuring that operating policies and procedures meet stringent international standards for consistency and reliability.
-
Product
PMA Suite For The PSA/PSL-3000: 802.3at (30W) PSE's
-
In-Depth System Testing of 802.3at and 802.3bt 2-Pair PSE's Using PSA-3000 or PSL-3000 instruments. Concurrently Analyze Up To 192 PSE Ports. Robust Emulation of Type-1, Type-2, and Type-3 (Class 4) PD's Including PoE LLDP. Assess PSE Power Administration Decisions. Assess PSE Power Management Behaviors. Static and Transient Reserve Capacity Analysis. Per-Port Variation and Uncertainty Analysis. Assess PSE Power Reliability Over Time.Colorful and Graphical Pop-Up Spreadsheet Reporting. Available to PSA-3000 and PSL-3000 as part of the Live PD Emulation license feature.
-
Product
5 kV Electric Motor Analyzer
MCE
-
The MCE is the most comprehensive static electric motor test equipment available on the market today. Through a series of powerful diagnostic tests, the MCE provides a complete look at the health of an offline motor. The MCE provides critical information to technicians allowing them to diagnose problems early, thus reducing unwanted downtime.
-
Product
Secondary Ion Mass Spectrometry (SIMS Analysis)
-
Rocky Mountain Laboratories, Inc.
Secondary ion mass spectroscopy is operated either in the dynamic mode (DSIMS) or the static mode (SSIMS). DSIMS is useful for profiling impurity and trace elements through films and interfaces. SSIMS is useful for characterizing polymeric materials and only measures the outermost molecular layer of a specimen.
-
Product
NI-9403, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module
780179-01
Digital Module
5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module - The NI‑9403 is a configurable digital I/O interface for input or output with shift‑on‑the‑fly capabilities. Each channel features transient isolation between the I/O channels and the backplane. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9403 for applications such as custom, high-speed counter/timers; digital communication protocols; and pulse generation. In a CompactDAQ chassis, you can use the NI‑9403 only as a static (software-timed) digital I/O module. You cannot use these modules to route timing or triggering signals.
-
Product
Fetal & Neonatal Test Equipment
-
Setting a new performance standard in Fetal/Maternal simulationTwo direct Fetal ECG'sFive full Maternal ECG leadsFour separate Fetal ECG tracingsThree Fetal ultrasound channels with "Triplets" capabilityThirteen Fetal static ECG ratesFifteen trends of Fetal data representing real-life case studies
-
Product
Power Rail Probe, 6 GHz
N7024A
Oscilloscope Probe
The N7024A power rail probe is for users making power integrity measurements that need mV sensitivity when measuring noise, ripple and transients on their DC power rails. The probe is designed for measuring periodic and random disturbances (PARD), static and dynamic load response, programmable power rail response, and similar power integrity measurements. Many of today’s products have tighter tolerances on their DC power rails than the previous generations of these products, and the N7024A power rail probe is designed to help users ensure their products meet these tighter tolerances.
-
Product
COMPUTERIZED AUTOMATIC RELAY TEST SYSTEM
CVRT-S16
-
CVRT-S8 & S16 are ideal for automatic testing of ELECTRO MECHANICAL AND READ RELAYS (only DC relays) both for static and dynamic characteristics. This system scans at one stroke, all the parameters of the relay as per definition of test procedure. The test sequence can be pre-programmed and stored in the disk. You can select the tests as per your requirement. Can include or exclude the test and you can have several options to match your test definitions. Semi skilled person can be engaged for actual testing, as he need not make any settings and need not interpret the readings. The system conducts the tests and gives PASS / FAIL indication on overall test results. If a printer is connected, each test result will be printed.Test Parameters : -> Coil Resistance.-> PickUp/Pull In /Operating Voltage or Current Linear Ramp Method or Step Method.-> Measure Pickup Contact Gap FBB-LBB V or mA-> DropAway/Drop Out/Release Voltage or Current Linear Ramp Method or Step Method.-> DropAway Contact Gap FFB-LFB V or mA-> % Release Dropaway/Pickup-> Contact Resistance of all contacts both Front and Back contacts.-> Operating Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while Operating @ above-> Release Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while release @ above-> Difference of Operate Time - Release Time.-> Bridging Test or Non Overlap Test.-> Transfer or Traverse Times while Operate and release.-> Operate Time @2nd Set Voltage or Current.-> Release Time @2nd Set Voltage or Current.-> Power Consumption @ Rated Voltage.-> Coil Current @ Rated Voltage at Room Temperature.-> Coil Resistance Corrected to 20deg C.-> Timing Waveform Graph for all active Contacts.
-
Product
Ionizers
ESD
-
Electrostatic discharge (ESD) is the release of static electricity when two objects come static control ESD IT-7000 Tabtop ionizerinto contact. Familiar examples of ESD include the shock we receive when we walk across a carpet and touch a metal door knob and the static electricity we feel after drying clothes in a clothes dryer. A more extreme example of ESD is a lightening bolt. While most ESD events are harmless, it can be an expensive problem in many industrial environments.
-
Product
Partial Discharge Testing
-
Weshine Electric Manufacturing Co., Ltd
Using the Windows system operating platform, you can freely choose ellipse, straight line, sine wave display, two-dimensional, three-dimensional graphic analysis mode, spectrum window, Q-V-F three-dimensional characteristic window, and static detailed measurement, observation and analysis of partial discharge pulse of one-cycle test voltage .
-
Product
Tensile Grips
-
Instron offers a wide array of tensile grip solutions engineered to suit virtually any materials testing application, with force capacities from one gram to two meganewtons covering fibers, films, metals, composites, elastomers, textiles, and more. From classic manual wedge and screw side action grips to pneumatic and hydraulic powered versions, Instron’s grips support static and dynamic testing across ambient and temperature environments. Built to global standards and backed by decades of durability and service, these tensile grips help labs reliably secure specimens while delivering consistent, repeatable test results—even for highly specialized or custom applications.
-
Product
Electrostatic Meter
STS 1
-
The electrostatic sensor STS 1 is a compact electrostatic meter with a digital display for measuring static charges in the range of positive and negative numbers easily and precisely. The wide range of measurement, the high accuracy, the reduced drift and a resolution of up to 1 V make the electrostatic sensor STS 1 an all-rounder for all fields of electrostatic measurements.
-
Product
Micro Analytical Balances
BM Series
-
Easy, fanless static elimination using a built-in ionizerBetter operability with a large weighing chamberInterlockable slide doors allowing efficient operation with both handsAutomatic calibration with an internal massClearly visible, white-backlit LCDBuilt-in temperature, humidity, and atmospheric pressure sensors
-
Product
Circuit Breaker Testing Equipment
HISAC Swift
-
HISAC Swift - Circuit Breaker Operational Analyser is meant for checking the performance of the MV Circuit Breakers. The Analyser contains various intelligent measuring modules designed for measuring parameters such as contact timings of Main/PIR & Auxiliary contacts, Close/Trip Coil Current characteristics and Static Contact Resistance of R, Y & B poles simultaneously. The results can be directly viewed on the TFT touch screen display in graphical as well as numerical form. It is possible to print the graph on a built-in thermal printer or download record to PC for further analysis on CPLOT software. This all in one instrument is best suited for gang operated CBs.
-
Product
Bench Top Ionizer Cleaning Box
EC-B
-
Panasonic Industrial Devices Sales Company of America
The EC-B Bench Top Ionizer allows direct ion emission to be paired with pulsed air emission to provide quick and effective removal of static charges as well as any dust that is present on the part. Three white LEDs illuminate the work piece to ensure complete dust removal. A powerful dust collecting fan exhausts dust quickly, preventing re-adhesion of dust.
-
Product
Container & Package Testing
-
*Incline Impact. *Drop. *Cobb. *Static and Dynamic Compression. *Dart Puncture. *Environmental Conditioning. *Vertical Linear, Rotary Motion, Sinusoidal and Random Vibration. *Internal Pressure. *Vacuum
-
Product
ELT STALKER Vector-finder
VF-121
-
The Vector-Finder Types VF-121 and VF 121A are unique in the Vector-finder series of direction finding antennas. They incorporate a proven design, electro statically shielded loop sensing element with modern solid state low noise analog and digital technology to allow detection and location of aircraft band signals. Both the VF-121 and the VF 121A incorporate a unique digital modulator which allows the user to more easily home-in on unmodulated carriers. Such cases occur at airports when transmitter may be accidentally keyed on during aircraft overnight layovers. The VF-121 is specifically designed to be used on airport premises where signal strengths are high. To compensate for very strong signals, an integral attenuator is also incorporated to allow the user to operate the unit close-in to aircraft. The VF-121A differs in that a high gain, low-noise preamplifier is utilized with the sensing element in order to hunt signals that may be weak or at a distance. The unit is ideally suited for the location of ELT transmitters in the field. Both units are tunable over the 118 MHz to 130 MHz aircraft frequencies and interface directly to the user’s aircraft band receiver or transceiver via the antenna jack. With the antenna system connected to the receiver, the user will hear the desired signal. If the signal is unmodulated, the digital modulator will generate a tone on the carrier. When the handheld unit is rotated about, an audible null on the received signal or the generated tone will be heard. This null aligns with the axis of the equipment case and represents the direction of the received signal. This direction may be read from the black dial compass mounted on the top of the enclosure. As the response is bi-directional, triangulation may be used to determine the true bearing when the true direction is not known.
-
Product
Energy Meter
SME 13A
-
SHANGHAI POWOO INDUSTRY CO., LTD
The SME12(13)-A is a single-phase static electricity meter which is integrated the functions of display, sampling, processing for measuring energy. SME12(13)-A Single-Phase Static Electronic Meter is applies for measuring single phase two wire (three wire) AC active energy which frequency is 50Hz or 60Hz. The meter complies with IEC62053 standard.
-
Product
Universal Testing Machines
UTM
-
Tinius Olsen is the leading specialist manufacturer and supplier of static tension and/or compression materials testing machines. Our machines are designed for use in research departments and quality control departments to measure the strength and product performance of materials. Using Tinius Olsen equipment it is possible to perform such tests on raw materials such as metals, polymers, textiles, rubbers, adhesives and food as well as finished components.
