-
Product
Telecom Test Systems
4301 Series
-
The 4301 is designed to work with a standard arbitrary wave form generator or signal source that can be triggered. The system can be ordered with an optional Fluke 281 arbitrary waveform generator, which comes pre-programmed and integrated into the 4301 system. When equipped with the Fluke 281 option, the 4301 provides a complete solution for GR-1089 Section 10/ATIS-0600315.2007 testing.
-
Product
Layer Release Systems
-
EVG's IR LayerRelease Technology is a fully front-end-compatible layer release technology that features an infrared (IR) laser that can pass through silicon, which is transparent to the IR laser wavelength. Coupled with the use of specially formulated inorganic layers, this technology enables an IR laser-initiated release of any ultra-thin film or layer from silicon carriers with nanometer precision.
-
Product
Humidity Generation System
2900
-
The Model 2900 Humidity Generation System is a self-contained system capable of producing atmospheres of known humidity using the fundamental "two-pressure" principle. This system is capable of continuously supplying relative humidity, dew point, frost point, parts per million, or other calculated values for instrument calibration and evaluation as well as for precision environmental testing.
-
Product
Measuring System
K-5201MA
-
To solve this problem, the following composition of the complex was chosen in the test stand conditions:laptop in a protected version PanasonicTBCF-53;measuring block - NIUSB-4431 with a set of vibroaccelerometers AP-2037;vibration excitation system LW 139.151-30 with mounting kit for the disk.The software of the complex provides the following functions:spectral analysis of vibration signals in the regulated range;search for natural excitation frequencies in given frequency ranges;Formation of database of existing disks;generation of reporting forms;and etc.
-
Product
Washwater Monitoring System
EG-100
-
Washwater Monitoring System for NOx and SOx Scrubber.Monitoring pH/Temperature, Turbidity, and PAH.EG-100 has flow type sensors.
-
Product
S-Parameter Measurement System
DPS08
-
KEYCOM provides S-parameter method measurement systems in two modes, the reflection mode and the transmission mode, to address the individual purposes. Both modes measure the complex permittivity (εr) and complex permeability (μr) at the same time, and the proper usage is as follows.
-
Product
D-Mic Testing System
BK3012V2
-
Easy to use and faster than human testers can load, the new BK3012V2 is the upgrade of our popular BK3012 D-Mic tester. Setup is even easier than for the BK3012 and you can enter specifications and be ready for testing in a few minutes. As well as testing, the BK3012V2 can be connected to a computer, so you can keep your results and analyze them for current quality and trends over time.
-
Product
Cost-Effective ATE System
PRO RACK ATE
-
Qmax Test Technologies Pvt. Ltd.
Pro-Rack is a cost effective ATE System, which comes with Modular Structure provision option to improvise and enhance much instrumentation based on the user’s requirements. Basically it is designed to cater to the needs of PCB test and repair depots, keeping in mind the changing PCB technology and the challenges in testing them off-line. It can provide complete PCB test and diagnostic functions for any kind of PCB including the latest very high density complex PCBs with high pin count PQFP, FPGA VLSI chips. AC /DC parametric tests enables testing of the DC parametric of device pins on the edge connector for input bias current, Fan out capacity ,Tri-state leakage currents, AC parametric measurements such as Input / Output Propagation delay Rise time / Fall time to further enhance fault coverage. Pro-Rack is designed with VPC Mass Interconnect adapter with 16 bit fixture ID interface to the UUT through simple clips and probes or through card edge or through a bed of nail test fixture.
-
Product
Fiber Geometry System
FG500
-
The FG500 is a fiber geometry system that measures the physical dimensions of the fiber including core, cladding, and coating diameter, non-circularity, and eccentricity. The FG500 is designed to produce accurate measurements quickly and with confidence.
-
Product
Acoustic Scoring System
AcoustiScore
-
Provide realistic weapons training. Consisting of a sensor and a data reception and display unit, the system senses the shock waves from passing projectiles and converts these waves into electronic signals for miss-distance measurement and display.
-
Product
Measurement System
MS-500 series
-
The MS series is suitable for pre-processing analog signals.The plug-in units of filters, differential amplifiers, isolation amplifiers, etc. can be installed into their frames.(16 channels at maximum/the JIS rack size)
-
Product
System Trace Emulators
XDS560v2
-
The XDS560v2 System Trace Emulator is the second generation of the XDS560-class emulator design from Texas Instruments. It provides cost effective real-time emulation, debugging, and high-performance System Trace (STM) for Texas Instruments devices over both USB and Ethernet PC interfaces.
-
Product
FPGA Test System
DO-254/CTS
-
DO-254/CTS™ is a fully customized hardware and software platform that augments target board testing to increase verification coverage by test and satisfy the verification objectives of DO-254/ED-80. The target design runs at-speed in the target device mounted on the custom daughter board. The simulation testbench is used as test vectors to enable requirements-based testing with 100% FPGA pin-level controllability and visibility necessary to implement normal range and abnormal range tests. The FPGA testing results are captured at-speed and displayed using a simulator waveform viewer for advanced analysis and documentation.
-
Product
Humidification Systems
-
The Humidity bottles are made from type 316 stainless steel. Swagelok fittings for gas inputs and outputs are welded into the bottle. Nafion tubing inserted into a type 316 stainless steel spring for support is coiled in the bottle to provide dew-point humidity level for the gas passing through the tubing. The bottle is insulated and heated using a silicone rubber flex-pad.
-
Product
Solder Paste Inspection System
KY8030-3
-
The new KY8030-3 delivers 3x fasterinspection without compromisingperformance and accuracy.Using patented dual projection,the system eliminates the criticalShadow problem that all 3D SPI systemscan be vulnerable to.Additionally, the new KY8030-3 has solvedthe PCB Warp problem that seriouslyimpacts inspection accuracyand reliability of result.
-
Product
Turret Drive Stabilization System
-
Curtiss-Wright Defense Solutions
Weapons' accuracy and reliability are crucial factors for combat success. The ability to accurately locate a target and stabilize the shot while moving out of the line of sight could make all the difference.
-
Product
Monitoring Systems
-
Our bestselling Accsense Ethernet Temperature Datalogger is designed for cost-effective temperature measurement and alarm in medical refrigerators, freezers, cryogenic storage and incubators. We also provide additional models of Accsense data loggers which monitor additional values including humidity, digital, pressure, and more.
-
Product
Rotary Torque Measurement System
-
Honeywell Industrial Automation
Honeywell's analogy telemetry rotary torque systems are often well suited for both short and long term testing and monitoring of torque or strain on rotating applications where other measurement methods are affected by vibration, dust, moisture, high RPMs, and large axial/radial shaft movements.
-
Product
Function Test System
Focus-FX
-
This is general function test system. User can change board model easily by replacing a test fixture and changing inspection program. We have variety of measurement instruments such as FX modules which can control commercial instruments. It is possible to add required modules into existing units as they are connected by USB port. User can expand as per desired inspection specification.
-
Product
Dynamic Component Test Systems
-
RedViking brings advanced engineering and proven implementation expertise to your next dynamic component test stand. We’ve designed entire fleets of multi-model and single-model test systems for new component development and production as well as military and commercial MROs. We have decades of experience building and implementing turnkey dynamic component test systems, and we’ll work with your teams virtually anywhere in the world.
-
Product
Optics Test Systems
Lens Test
-
Optik Elektronik Gerätetechnik GmbH
LensTest enables the measurement of air gaps, lens thickness, lens radii and lens surface centration errors in mounted lenses as well as the active alignment of lens surfaces during optics assembly for centering without rotating the assembly.
-
-
-
Product
Dimensional Metrology Systems
-
We are a global provider of optical industrial measurement technology for quality assurance of complex components with tight tolerances. With Bruker Alicona measurement systems, users measure dimension, position, shape, and roughness by using only one optical sensor. Measurement systems are applied in both research and directly on the shop floor.
-
Product
Magnetic Research System
MagRS
-
The MagRS base system comes with a 4 or 7 in magnet, with additional options to customize the system for your experimental needs. Choose to add VSM capability, temperature option accessories, or optical access. MagRS comes standard with ExactGAP magnet pole gap indexing and GlideLOCK precision sample positioning.
-
Product
Security and Traffic Monitoring System
-
Information System Technologies Inc.
ISTI’s versatile sensor nodes can support multiple sensing types including acoustic, seismic, visible/IR, and scanning laser. Several eye-safe scanning lasers form a distributed wireless sensor network and can continuously and accurately track as well as monitor ground vehicles and personnel in a surveillance area. This system provides super-fine angular and range resolution to precisely locate moving targets. Among other key benefits are: day/night operational capability, continuous monitoring and surveillance without blind spots, 360 degrees field-of-view, large coverage area, multiple closely spaced target tracking, threat classification, and automatic alarm generation. The system can be used in applications such as traffic monitoring, intrusion detection, border control, airport runway collision and incursion avoidance, and perimeter security.
-
Product
DI Lab System™
-
Comprehensive Product Engineering and Failure Analysis Lab system for complete device analysis and physical defect isolation.
-
Product
Free Measurement System
CFMS
-
The Cryogen Free Measurement System (CFMS) from Cryogenic Ltd is a modular research system designed to enable the user to perform a wide range of material characterisation experiments in variable field and variable temperature environments.
-
Product
Machinery Vibration Protection System
-
Alta Solutions' machinery protection systems can quickly detect abnormal machinery conditions and shutdown your machinery to avoid catastrophic failures and further damage.
-
Product
Environment Monitoring System
ENVIROMUX-2D
-
The ENVIROMUX-2D supports 2 external configurable sensors, 5 digital inputs, and 1 output relay for control of external devices. It features 2 USB ports for USB modem, USB flash drive, or USB LCD screen. Linux inside.
