-
Product
Interface Card - 1-2 Channels of MIL-STD-1553 Networks on a PMC Form Factor with Ethernet Backplane Interface
PMCE-1553
Interface Card
PMCE-1553™ is an innovative product that provides 1553 operations via 10/100/1000 Ethernet IP/UDP local area networks (LAN) backplane. PMCE-1553 is a standard PMC form factor card, but instead of PCI backplane, PMCE-1553 uses the P4 connector for Ethernet based control and communications.
-
Product
Interfaces
-
Layer N communication interfaces enable wired and wireless communication of Smart Interfaces to the Layer N Smart Gateway to transfer application data directly into the cloud.
-
Product
PXI-8430, 8-Port, RS232 PXI Serial Interface Module
779536-01
Serial Interface
8-Port, RS232 PXI Serial Interface Module - The PXI‑8430/8 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard COM ports … for compatibility with programs that use serial communications.
-
Product
GPIB Interfaces
-
Control older devices that use the ANSI X3.28 protocol from the GPIB Bus. Available in board or rack mountable Minibox™ form.
-
Product
Digital/Pattern/PE Card
PA32S
Interface Card
The PA32S represents a new level of performance and capabilities for PXI-based digital instrumentation. Based on the proven architecture of the PE32, the PA32S offers high performance pin electronics and an enhanced timing generator in a compact, 3U PXI form factor. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 512 bi-directional pins (16 boards). The PA32S also supports deep pattern memory by offering= 32 M of on-board vector memory with dynamic per pin direction control and with test rates up to 33 MHz. With new 32M capture/log memory, PA32S can capture 32 channels fail log.
-
Product
Interface Board for Gigabit Ethernet
40-965-910
Interface
The 40-965-910 is a converter card for the 40-201 Ethernet/AFDX Fault Insertion Switch. Adapts the 78-Pin D-type connector on the front of the module to 4 RJ45 sockets and one 9-way D-type connector for fault signals. Allows the fault insertion testing of Gigabit Ethernet signals.
-
Product
Ethernet Module
M4K-ETH
Ethernet Interface
The M4K-ETH is an intelligent Gigabit Ethernet interface module for the multiprotocol Excalibur 4000 family of carrier boards. The module supports 10Mhz, 100Mhz and 1Ghz Full Duplex UDP/IP Ethernet.
-
Product
Interface
RAR-XMC
Interface
Designed for embedded, laboratory and simulator applications, the RAR-XMC supports maximum data throughput on all channels while providing onboard message scheduling, label filtering, multiple buffering options, receive message time-tagging and error detection, and IRIG-B receiver (AM or DC/TTL) and generator (DC/TTL).
-
Product
Network Interface Card
NIC10GBT
Interface Card
The NIC10GBT is a dual port 10GBase-T XMC module that brings 10GbE expandability to new and existing embedded systems with available XMC slots.
-
Product
PXIe-6594, FlexRIO High-speed Serial Module (28 Gbps), KU15P
786939-01
Serial Interface
PXIe, 28 Gbps, 8-Channel PXI High-Speed Serial Instrument. - The PXIe-6594 is designed for engineers who need to validate, interface through, and test serial protocols. It includes a Xilinx Kintex Ultrascale+ FPGA to implement various high-speed serial protocols, and it is … programmable in LabVIEW FPGA for maximum application-specific customization and reuse. The PXIe-6594 takes advantage of FPGA multigigabit transceivers for up to eight TX and RX lanes.
-
Product
PCI-8511, 2-Port, Low‑Speed/Fault-Tolerant CAN Interface Device
780682-02
CAN Interface
The PCI‑8511 is a fault-tolerant controller area network (CAN) interface for developing applications with the NI‑XNET driver. The PCI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
Interface Systems
-
To build a complete and accurate force measurement system, it’s essential to integrate a compatible sensor, instrumentation, and proper cables and connectors. Start with a high-quality load cell or torque transducer that suits your application needs. Pair it with compatible instrumentation, such as a signal conditioner, digital display, or data acquisition system, that can properly excite the sensor and interpret its output. To ensure signal integrity and reliable performance, use shielded, appropriately rated cables and connectors designed for your environment and sensor type. When all components are correctly matched and system calibrated, the result is a precise and dependable measurement system.
-
Product
sbRIO-9870, Non-Enclosed, 4-Port, RS232 C Series Serial Interface Module
780922-01
Serial Interface
The sbRIO‑9870 adds RS232 serial ports to CompactRIO systems. The serial ports are accessed directly from the FPGA to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The sbRIO‑9870 supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions. Non-enclosed modules are designed for OEM applications.
-
Product
PXI-8432, 2-Port, Isolated, RS232 PXI Serial Interface Module
779743-01
Serial Interface
2-Port, Isolated, RS232 PXI Serial Interface Module - The PXI‑8432/2 is a high-performance interface for high-speed, port-to-port isolated communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
KYK-13 Interface
IP-Crypto
-
The IP Crypto is a special version of the IP-Parallel-HV. The basic design features are retained and an interface to a KYK-13 is provided. The original KYK-13 interface uses the 6.5V reference output, a transfer request output, and 3 inputs for clock, data and switch. The outputs for the general purpose section are reduced to 23 in number. The inputs are all available through the filter or after processing by the KYK-13 interface.
-
Product
PCI, IEEE 488 GPIB Instrument Control Device for Windows, Low Profile
783007-01
Interface
The PCI‑GPIB is a plug‑and‑play IEEE 488 interface for PCs and workstations with PCI expansion slots. The PCI‑GPIB can sustain data transfer rates of more than 1.5 MB/s using the IEEE 488.1 three‑wire interlocked handshake. It also implements the high-speed IEEE 488.1 noninterlocked handshake (HS488) for benchmarked data transfers at more than 7.7 MB/s. The onboard bus master DMA controller means that there are no microprocessor interruptions in data transfer.
-
Product
Vehicle Interfaces
-
Easily connect your computer to multiple vehicle networks. We have solutions for nearly all currently used networks and protocols.
-
Product
USB-8451, 250 kHz I2C, 12 MHz SPI I2C/SPI Interface Device
779553-01
Interface Module
The NI USB‑8451 is a master interface for connecting to and communicating with inter-integrated circuit (I2C), System Management Bus (SMBus), and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8451 is a portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices or toggling LEDs. The USB‑8451 can be physically located more closely to I2C/SPI devices than PCI interfaces, reducing I2C bus length and minimizing noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
Interface Converter
ZET 7176
-
Interface converter Ethernet/Wi-Fi↔CAN ZET 7176 is used for connection of CAN interface instrument communications nets based on digital transducers to PC over Wi-Fi or Ethernet. Wi-Fi or Ethernet network throughput rate allows to immediately fulfill commands and transmit great scope of data. Shared use of ZET7176 and ZET 7172 interface converters allows arranging instrument communications nets with radio linked transmission interface.
-
Product
Multi-Channel Interface Module
PC104P-MA4
Interface Module
Alta Data Technologies’ PC104P-MA interface module is a multi-channel, multi-protocol 1553 and ARINC PC104-Plus interface card supported by the latest software technologies. The PC104P-MA4 card is based in the industry’s most advanced 32-bit protocol engine, AltaCore, and by a feature rich application programming interface, AltaAPI, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. The hardware and software package provides increased performance and reduces intergration time.
-
Product
Interfacing Components
-
Spring contacts and lands for PCB interconnection and a wide range of data, power and battery charging applications including: charging batteries in portable instruments power and data transfer pins in a docking station integral compliant contacts, such as for an antenna contact in a mobile phone board to board spring contacts for use in computerised gaming systems and telecommunications units
-
Product
Network Interface Card
PMC-GBIT-DT2BP
Interface Card
The Ethernet network interface complies with the IEEE 802.3 specifications for 10BaseT, 100BaseTX, and 1000BaseT over category 5 twisted-pair cable. Full-duplex and half duplex modes are supported. The PMC-GBIT-DT2BP is compliant with standard singlewide PMC IEEE P1386.1, PCI 2.2, and PCI-X 1.0 specifications.
-
Product
Interface Module
MRS4
-
The mezzanine provides connection of up to four input and four output interface lines.
-
Product
Network Interface
-
VadaTech offers AMC Network Interface Cards (NICs), FMC networking modules and ATCA rear transition modules (RTMs) with a wide range of connector interfaces to make it easier for you to integrate an embedded computing system into your solution.
-
Product
PCI-8432, 4-Port, PCI, Isolated, RS232 Serial Interface Device
779145-01
Interface
The PCI‑8432/4 is a high-performance interface for high-speed, port‑to‑port isolated communication with RS232 devices. The PCI‑8432/4 features high-performance DMA transfers, multithreading, and multiprocessor support. NI … serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PXI DeviceNet Interface Module
Interface
PXI DeviceNet Interface Modules have an onboard microprocessor and optically isolated physical layer to communicate with a DeviceNet network system as a master (scanner) or slave device. The modules ship with a high-level API that provides complete access to a DeviceNet network and features easy access to device data and streamlined explicit messaging. PXI DeviceNet Interface Modules are ideal for prototyping DeviceNet systems, PC-based control, embedded control systems, PC-based human machine interface (HMI), and DeviceNet network management utilities.
-
Product
Ethernet Bridge Converter for MIL-STD-1553 and ARINC
ENETX-MA4
Ethernet Interface
eNetX-MA4™ is an innovative product for “remoting” 1553 & ARINC-429/717 operations on 10/100/1000 Ethernet local area networks (LAN). eNetX-MA4 is a very small, low-power, rugged device that provides real-time UDP connectivity to for 1-2 dual redundant 1553 (A/B) busses and 4 ARINC channels. Tested to MIL-STD-704F/810G/461F and DO160.
-
Product
PXIe-SMN Interface Card
-
Avionics Interface Technologies
2.125 Gbps Optical loop networkSingle-mode and Multi-mode optical interfaces supportedUp to 256 Shared Memory Network nodes supportedUp to 200 MByte/sec sustained data ratesMaximum 500 nS latency between nodesNetwork interrupts supportedSoftware Drivers available for Windows (7/8), Linux, LabVIEW Real-Time, and VxWorks
-
Product
CPCI Or PXI Communication Interface Board
MS 1706
-
*Memory and IO Read Write Cycles*External Interrupts*32 bit Data Bus*30 bit Address Bus*Control Signals for external interface*Four RS232 PORTS with full handshake signals*Four RS232/RS422 PORTS without handshake signals*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Interface ICs
-
Easy to use, flexible, and reliable. Allegro’s sensor interface ICs offer accurate and fast output for signal conditioning in a wide range of applications, from electric vehicle HVAC systems to transmission oil pressure. Our innovative algorithms deliver robust EMC performance and provide critical diagnosticsthat support automotive safety.
