-
Product
MOSFETs For High Frequency Amplifier
-
The MOSFETs shown below are best suited for amplification of high-frequency signals.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Transconductance & Transimpedance Amplifiers
-
Measurements International Ltd.
0 to 100 Amps – AC, 0 to ± 100 Amps – DC, Voltage Compliance ± 5 Volts, IEEE-488 Interface, Resistive, Capacitive, Inductive Loads.
-
Product
Difference Amplifiers
-
A difference amplifier is a special purpose amplifier designed to measure differential signals, otherwise known as a subtractor. A key feature of a difference amplifier is its ability to remove unwanted common mode signals, known as common mode rejection (CMR). Unlike most types of amplifiers, difference amplifiers are typically able to measure voltages beyond the supply rails, and are used in applications where large dc or ac common-mode voltages are present. They are ideal for current and voltage monitoring. Analog Devices offers a range of difference amplifiers, optimized for low distortion, low power, or high voltage performance.
-
Product
Unipolar Variable Gain High Speed Amplifier
F70PV
-
The F70PV is a very fast, unipolar, linear amplifier having a variable amplification of 0-10 times and capable of voltage output of +70V. Any functiongenerator or arbitrary waveform generatoror any othe signal source can be used as an input device. The amplifier's output is linear from DC up to ca 10 megahertz range. It can be used in a wide range of high speed applications.
-
Product
ADC Drivers Fully Differential Amplifiers
-
Differential amplifiers allow the process of single-ended input to complementary differential outputs or differential inputs to differential outputs. These amplifiers feature two separate feedback loops to control the differential and common-mode output voltages. Analog Devices fully differential amplifiers are configured with a VOCM pin, which can be easily adjusted for setting output common-mode voltage. This provides a convenient solution when interfacing with analog-to-digital converters (ADCs). ADI also offers a series of differential receiver products that convert differential input signals to single ended output.
-
Product
Saluki SE2031 DSP Lock-In Amplifier
-
SE2031 Digital Lock-in Amplifier provides an excellent performance within its bandwidth from 1 mHz to 10 MHz. With the advantage of the latest digital signal processing technology and high-speed 16-bit ADC, SE2031 can easily detect the phase and the magnitude of weak signals overwhelmed by various large noise. The performance of SE2031 is as good as other lock-in amplifier brands, even better in some certain parameters, such as measurement accuracy, SNR, dynamic reserve. Otherwise, SE2031 integrates some special functions like multiple harmonic measurement, which meets the needs of scientific research and industrial application well.
-
Product
SW Range Broadband Power Amplifiers 0.8 GHZ - 4 GHZ
SW Series
-
Class A solid stateBroadband (instantaneous single band): 0.8 GHz 4 GHzTypical output power : 18 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 13 W and H < -20 dBc up to 2.5 GHz andP1dB > 12 W and H < -20 dBc from 2.5 GHz to 4 GHzAir cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Rack3 years standard warranty
-
Product
High Voltage Amplifiers
-
Advanced Energy is a trusted high voltage power supply provider with over 40+ years of experience. Our extensive line of Trek high voltage amplifiers offer numerous voltage and current ranges to accommodate your demanding applications. Protect against output short circuits and over-voltages. For protective shutdown, utilize automatic crossover compliance limits or current trip features.
-
Product
Broadband Power Amplifier
PAS-00023-25
-
* Solid State Power Amplifier* Gain : 46 dB typ.* High IP3, 48.0 dBm typ.* Bench Top Case* Internal Cooling Fans* Over Temperature Protection* Type N Connectors
-
Product
Portable Power Amplifier
PA30Bip
-
PA30Bip portable power amplifier is designed with linear amplifier principle. It is very light portable solution with three channels of current output and four channels of voltage output.
-
Product
Fiber Transmitter With Fiber Amplifier
FTFA 822B - 824B
-
- Work as Transmitter & Fiber Amplifier- AGC - Automatic Gain Control- Built in RF Booster- Higher RF at next connected Node- Maintain MER/BER for Digital FTTH Transmission- High Quality DFB Lesers with Isolaters- Variable SLOPE Control- Output Wavelength : 1310nmPower Options :- 40V DC- 12V DC / 2 Amp- STB Adapter along with PSP- 7.4V, 2600 mAH Battery
-
Product
Lock-in Amplifier
HF2LI
-
The Zurich Instruments HF2LI (high-frequency, 2 inputs) is a digital lock-in amplifier covering the frequency range between DC and 50 MHz. It features 2 physical input channels so that it can replace 2 devices in many measurement setups. The 128-bit digital signal processing delivers superior precision thus boosting both the noise performance and the dynamic reserve. With these unprecedented capabilities, the HF2LI brings lock-in amplification to a new level and enables new applications in a frequency range that was previously tied to analog instrumentation. The computer is connected by a high-speed USB interface, which allows data acquisition at high rates. The HF2LI is delivered with a fully featured graphical user interface and a choice of programming interfaces that greatly add to the usability of the instrument.
-
Product
Ultra-low Noise High Voltage Amplifier
WMA-200
-
The Falco Systems WMA-200 model is a high quality, high voltage, linear laboratory amplifier optimized for experiments requiring world-class, ultra-low output noise. The excellent noise performance, combined with the wide bandwidth and large voltage range make this amplifier the preferred choice for the most demanding precision positioning systems. The amplifier will routinely enable sub-atomic positioning resolution with piezo positioning systems and MEMS devices. Two WMA-200 amplifiers and a WMA-IB-LN phase inverter - buffer can be used to double the output voltage.
-
Product
Low Phase Noise Amplifiers
-
Pasternack's low phase noise amplifiers cover select frequency bands ranging from 1.5 to 18 GHz with residual phase noise levels as low as -180 dBc/Hz @ 10 KHz offset. Additional performance specs include small signal gain ranging from 9 to 14 dB, with typical noise figure of 5.5 dB. Psat levels for these amplifiers range from +16 to +25 dBm with Output IP3 levels as high as +34 dBm. All models feature single DC voltage supplies and input/output RF ports are internally matched for 50 ohms with DC blocking capacitors. These compact module assemblies require no external components and are available in rugged Kovar metal drop-in packages that are gold-over-nickel-plated and support field replaceable SMA connectors. All models are EAR99 and guaranteed to meet MIL-STD-883 test conditions for hermeticity and temperature cycle.
-
-
Product
YDFA Amplifier
-
a high-gain three staged polarization maintaining optical amplifier unit designed for applications requiring high efficiency optical amplification in the 1060 nm regime in both CW and pulse mode operations.
-
Product
Linear Power Amplifier
LPA-2 50/100W
-
The LPA-2 is the next generation high-power amplifier for Power Line Carrier Communications and adds features and efficiency superior to all previous designs using the latest technology. It offers flexibility plus user-friendliness on its input and output such that it can be used with any power line carrier system. Two 50W units can be combined for a 100W output and to provide redundancy.
-
Product
Crossed-Field Amplifiers
CFAs
-
Communications & Power Industries
CPI BMD’s crossed-field amplifiers (CFAs) are broadband, phase-stable microwave amplifiers used in coherent radar chains to efficiently generate very high peak output powers from relatively low input voltages which can be either applied to the cathode or an electrode similar to a TWTs cathode or grid pulsing, and in relatively small, lightweight packages. These characteristics make CFAs particularly well-suited for applications in which the transmitter must be either airborne, transportable, mobile or portable.
-
Product
Low Noise Super Wide Band Amplifiers
WBA Series
-
WBA series low noise amplifiers have the octave bandwidth from MHz to GHz. With super low noise figure and exceptional low VSWR, WBA series LNA achieves exceptional gain flatness accross octave or multi-octave bandwidth.
-
Product
Shortwave Power Amplifier
OM2501A (OM3501A)
-
The OM Power model OM2501A and OM3501A are designed for all short wave amateur bands from 1.8 to 29.7 MHz (including WARC bands) and all modes. OM2501A is equipped with a FU728F or GU84B ceramic tetrode and OM3501A is with GU78b ceramic tetrode.
-
Product
Microwave Power Amplifiers
-
Spanawave/Giga-tronics Microwave Power Amplifiers deliver outstanding performance and exceptional value. These ultra-broadband amplifiers have excellent pulse performance and modulated signal fidelity, ideal for testing in wireless communications, defense EW and radar testing and general purpose microwave laboratory applications. Have the power you need to overcome cable and switching losses, or to drive higher power mixers, detectors and very high power amplifiers.
-
Product
E-Band Low Noise Amplifier MMIC
AWL-7186
-
The AWL-7186 is a 4-stage ultra-low noise amplifier that provides a noise figure of less than 3.5 dB, an output P1dB of +8 dBm, and an adjustable gain range of 15 dB. The MMIC features exceptional gain flatness and superior noise performance over a very wide bandwidth. It is implemented in 0.1 um GaAs PHEMT technology.
-
Product
Distribution Amplifiers
-
High-performance distribution amplifiers (DAs) for sending digital or analog computer, video, audio, and data signals to multiple devices.
-
Product
Premium Headphone Amplifier
A 20
-
A new standard for headphone amplifiers that brings out the potential of Tesla drivers. Premium headphone amplifier that inherits the design of A 1.
-
Product
C & L-Band Separate Raman Fiber Amplifier
RFA7000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
Optic Node With Amplifier
OX 755
-
Converts even weak Optic Signals to a high quality RF Signal. LED BAR Optic Level Display has been provided for ease of system maintenance. They are best suitable for Analog as well as Digital transmission to maintain BER, MER Characteristics.- High Quality Nodes cum Amplifier- Frequency 40 ~ 1000 MHz- Good Sensitivity of -11 dBm- RF O/P 110 dBµV at 0 dBm Optic I/P- High Voltage Surge Protection- LED Optic Level Display- Powder Coated Housing
-
Product
Fiber Transmitter With Fiber Amplifier
FTFA 844
-
- Auto Switch over from Fiber to RF & Vice versa- Works as Transmitter & Fiber Amplifier- AGC / MGC - Automatic & Manual Gain Control- Very High MER / BER- High Quality DFB Lasers with Isolators- RF Input : 78dB ~ 90dB- Optical Input : -8dBm ~ +2dBm- Optical Wavelength : 1310nm- Power : 110VAC ~ 240VAC, 50HzSpecifications:- Bandwidth: 47 ~ 860 MHz- Input RF Level: 75 ~ 85dBuV- Input Optical Level:- -8dBm ~ +3dBm- SMPS Power Supply:- 110V AC ~ 265V AC- Power Consumption: 50Watt- AGC Range: 0 ~ -8dBm
-
Product
UX Range Broadband Power Amplifiers 2 GHZ - 6 GHZ
UX Series
-
Class A solid stateBroadband (instantaneous single band): 2 GHz 6 GHzTypical output power : 15 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 12 W and H < -20 dBc up to 4 GHz andP1dB > 11 W and H < -20 dBc from 4 GHz to 6 GHzAir cooling: self contained fansCan operate in full mismatch conditions without damageUpgradable to UX 30 possible (4U)Reliable, efficient and robust19" Rack3 years standard warranty
-
Product
Low Noise Amplifiers
-
Our range of ITAR Free, Low Noise Amplifiers (LNAs) cover a variety of applications but are primarily suited to airborne, maritime and ground based radar systems. LNAs are primarily intended to minimise added noise whilst providing high gain so design focusses on the parameters associated with the noise response of the amplifier. They are usually the first amplifier in the Radar detection chain and will have the lowest noise figure.
