P.862
'Perceptual Evaluation of Speech Quality'
-
Product
Dual Channel Dynamic Data Simulator
LS-77-SS
-
The Lumistar LS-77-SS PCI Dual Dynamic Data Simulator with optional bit synchronizer allows two command simulators one bit synchronizer, and a time code reader/generator in a single short PCI board. The two Command Data Simulators and Time Code Reader/Generator are implemented in FPGA using a next generation design based on the LS-70-P. The optional bit synchronizer is achieved using the Lumistar LS-40-DB low-profiledaughterboard.
-
Product
Downloading Multifunction Tester
ET4500
-
The new ET4500 tester carries out all the tests needed to verify the safety of electrical installations in domestic, commercial and industrial wiring installations in accordance with the latest regulations.
can be used to carry out 3 wire earth testing and has on board memory to store and download all installation test results for documentation.
Everything about the new ET Series has been designed to save time and make testing easier.Fast, reliable high current and non-trip loop testing comes as standard together with a high level of input protection and a CAT IV safety rating .Supplied with a full range of accessories.
-
Product
3U 1-Slot OpenVPX P&G, Aperture E, VITA
101V301P03-9X13
-
3U 1-Slot OpenVPX Power & Ground, Aperture E, Supports VITA 66.4/67.3A/67.1 in J2B, Pass through, w/o ROHS, Max data rate (Gbps) 25.
-
Product
Sine Vibration Control
-
Sine control is one of the two basic and most common excitation modes for Environmental Shaker testing. This control mode performs real-time closed-loop control of swept sine vibration. The m+p VibControl vibration control system allows the user to designate all input channels as control, watchdog and/or measurement channels.
-
Product
Bench/System Precision Linear Regulated DC Power Supply With Digital Control, Single Or Triple Outputs, 105 To 242 Watts, With/without Remote Interfaces
QL Series II
-
Advanced dc power supplies, single or triple outputUp to 112 watts per outputVery high precision, very low noise, excellent dynamicsAdvanced user interface with numeric and rotary controlMultiple voltage/current ranges for increased flexibilityMultiple non-volatile memories for power supply set-upsSwitchable remote sense provides perfect load regulationComprehensive protection including OVP and OCP tripsCompact bench footprint; modular width for rack mountingAuxiliary output fully variable 1.00V to 6.00V at 3A with selectable voltage and current metering (T models)Bus programmable via USB, RS232, GPIB or LAN (P models)LAN interface is LXI compliantDuplicate power and sense terminals at rear (P models)
-
Product
Data Acquisition Systems
-
m+p Coda is a full-featured turnkey software platform for data acquisition, signal analysis and monitoring. Complete turnkey operation provides quicker time to test by eliminating costly application programming and long learning curves. The extensive built-in features and tools offer a functionality that was previously available only in custom packages. The intuitive graphical user interface facilitates set-up, operation and analysis, thus leading to precise, repeatable results quickly.
-
Product
Condensate Chambers
-
Parker Condensate Pots play a key role in maximising the accuracy of differential pressure flow measurement on steam or vapour applications. Condensate Pots can significantly improve flow measurement accuracy in differential pressure measurement systems by providing an interface between the vapour and liquid phases.
-
Product
Energizer
ISOTTA
-
Essentially made up of a stainless steel cylindrical body of tubular shape, the energizer has a front section that may be unscrewed (cartridge chamber), apt to contain an 8-bore blank cartridge, or industrial type (easily found in every gun shop). This cartridge chamber is without barrel, thus permitting the axial ejection of the energy wave, caused by the explosion of the cartridge, generating waves of type 'p' (longitudinal) and type 's' (transversal).
-
Product
3U 1-Slot OpenVPX P&G, Aperture E, VITA 66.4/67.3A/67.1 in J2B, Module
101V301P03-9004
-
3U 1-Slot OpenVPX Power & Ground, Aperture E, Supports VITA 66.4/67.3A/67.1 in J2B, Module TE 2226880-1, Pass through with VITA 66.4 ctr in J2B and RT2-R ruggedized VPX conn, w/o ROHS, Max data rate (Gbps) 3.125.
-
Product
240V Socket Tester Check Plug
CP501
-
The most popular socket tester available - detects 28 fault conditions.
A quick and easy way to ensure that 13A sockets are correctly wired, indicated by 3 bright long life LEDs.
Wiring faults are indicated by one or more of the LEDs failing to illuminate, with the pattern of lit LEDs indicating the type of fault detected. This fail-safe system means that any LED not lit indicates a fault. The robust ABS housing has a sculpted shape for easy removal and there is a look up chart on the tester for quick fault diagnosis.
The plug induces less than 5mA of earth leakage, well below RCD trip thresholds.
-
Product
Current To Pressure Measurement Trainer
-
Unitech Scales And Measurements Pvt. Ltd
Current to Pressure Trainer. This setup comprises of a I to P converter fitted on a base. Two pressure gauges are fitted one at the input side and the other at the output of the I to P converter. A current source with digital display is provided to excite the I to P converter. A constant air supply should be provided to the system at 20 PsI Pressure from a standard compressor.
-
Product
Powerful In-Circuit Production Flash Programmer
CYCLONE FX
-
P&E Microcomputer Systems' Cyclone FX programmer is is a powerful in-circuit, stand-alone programmer that supports a wide range of ARM Cortex and NXP® processor families. It's a versatile tool that offers on-board storage of programming images, provides power to the target, supports manual or automated programming, and has an easy-to-use touchscreen interface. Programming may be launched by a single button press without a PC or automatically from a PC via the automated control SDK. The Cyclone may also be used as a debug probe during development.
-
Product
3U 1-Slot OpenVPX P&G, Aperture E, VITA
101V301P03-9X12
-
3U 1-Slot OpenVPX Power & Ground, Aperture E, Supports VITA 66.4/67.3A/67.1 in J2B, Module Smiths Interconnect 415-00004, Pass through with VITA 66.4 ctr in J2B, w/o ROHS, Max data rate 10 Gbps.
-
Product
TV Amplifiers
-
PLANAR broadband amplifiers are designed to amplify television signals in the range up to 862 MHz in the forward direction, as well as to transmit internal system signals in the reverse direction in cable distribution networks.
-
Product
AC Power Source
61600 Series
-
Built-in PFC, provide input power factor over 0.98 (full load)AC+DC output mode for voltage DC offset simulationProgrammable voltage,current limitComprehensive measurement capability,V, Hz, Irms, Ipk, Iinrush, P, VAR, VA, PF, CF of current and etc.High output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlOne-key recall for 9 different voltage and frequencyProgrammable slew rate setting for changing voltage and frequencyAnalog input for power amplifierOptional Analog programming interfaceOptional GPIB and RS-232 interface(Model 61601~61605)Full protection: OP,OC,OV and OT protectionEasy use graphic user interface: softpanel (option)Capable of delivering power output up tp 90KVA by implementing Master-Slave operation
-
Product
Modal Analysis
-
The Modal Analysis package is part of m+p Analyzer, m+p international's dynamic signal analyzer for noise & vibration measurements and analysis. It provides a complete set of tools for observing, analysing and documenting the vibrational behaviour of machines and mechanical structures. Software modules are available for classical and operational modal analysis, shaker measurements (SIMO and MIMO) as well as for ODS, SDOF and MDOF analysis. A modal model validation module is also provided.
-
Product
3U 1-Slot OpenVPX P&G, Aperture J
101V301P05-9X12R
-
3U 1-Slot OpenVPX Power & Ground, Aperture J, Supports VITA 67.3D , Pass through, w/ROHS, Max data rate (Gbps) 10.
-
Product
47~2600MHz Digital TV & Satellite TV PIN Optical Receiver
HRS-26D/P
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HRS-26D/P optical receiver, adopting high-sensitivity PIN detector, receiving sensitivity is -22dBm, typical value -13dBm. It can receive analogue and digital signal with the frequency of 47~2600MHz on a single fiber, and compatible with any FTTx PON to achieve triple-network combination between Analog TV(<10CH), Digital TV (DVB-C, DVB-T), Satellite TV (DVB-S) and Internet & FTTH.
-
Product
Discrete Device Test System
-
capability to perform parallel testing of power discrete devices. As the standard specifications of mainframe, 341-TT/P has 1.2kV/20A and 351-TT/P has 2kV/50A capabilities. These systems have 2 testing subsystems, each of which has 4-station capability by multiplexing to 4 handler/prober stations for high volume production testing.
-
Product
P Series Panel Meters
ST-60
-
Standard Electric Works Co., Ltd
● DC up to 30A● AC up to 30A● Case and Composition: Acrylic resin front. Bakelite case. ABS case. Four studs mounting.● Accuracy :DC : Class 2.0 AC : Class 2.5 Rectifier : Class 2.0● Color：Black case, white scale plate.● Pointer：Tube type, color in black or red.
-
Product
Dynamic Signal Analysis
-
m+p Analyzer is a fully integrated solution for dynamic signal measurement, analysis and advanced reporting of all noise and vibration, acoustics and general dynamic signal applications. Comprehensive time and frequency analysis is available with both online and offline data processing. Complete with advanced application wizards the m+p dynamic signal analyzer makes light work of gathering data, displaying results, performing specialized analysis and generating customer ready reports – all within one user interface. m+p Analyzer is designed for noise and vibration applications in the field and in the lab.
-
Product
Vibration Control
-
m+p VibControl vibration controllers for advanced vibration control and shock testing from 4 to hundreds of input channels are used by many of the leading environmental test laboratories throughout the world. The endusers appreciate the intuitive operation, the extensive analysis and reporting functions, the numerous upgrade possibilities and, of course, the excellent stability and high quality level of the m+p vibration control systems. Applications range from normal to very extreme conditions, and also include rough transportation circumstances.
-
Product
NI-9244, 400 Vrms L-N, 800 Vrms L-L, 50 kS/s/ch, 24-Bit, 3-Phase C Series Voltage Input Module
783106-01
Voltage Input Module
400 Vrms L-N, 800 Vrms L-L, 50 kS/s/ch, 24-Bit, 3-Phase C Series Voltage Input Module - The NI‑9244 performs single-ended analog input. The wide measurement range makes it ideal for high-voltage measurement applications such as phasor measurements, power metering, power quality monitoring, industrial machinery, and motor test. You can also perform transient and harmonic analysis with high-speed simultaneous sampling. The NI‑9244 offers three channels, so you can connect single‑ or three‑phase measurement configurations such as WYE and delta. You can incorporate the NI‑9244 into systems to meet standards such as IEC 61010‑1, C37.90 and C37.60, IEC 60255‑22‑(1:7), IEC 60255‑1, C37.188 Class M and P, EMC section of IEC 60870, EMC sections of IEC 61850, IEC 61000‑4‑30 Class S, and IEC 61000‑4‑7.
-
Product
In-Circuit Debugger for RS08 Family of Microcontrollers
ICDRS08
-
P&E's ICDRS08 is a powerful tool for debugging code. It uses the processor's background debug mode Module(BDM), via any of P&E's RS08 compatible interfaces (see product add-ons for more information), to give the user access to all on-chip resources.
-
Product
Flow Control Set Up Using PID Controller
ULP-25O & ULP-25T
-
Unitech Scales And Measurements Pvt. Ltd
Flow Control Setup Comprises of a Orifice with DPT to measure flow Rate. The flow of water is controlled by Control Valve with pneumatic actuator. I to P converter is provided to control the actuator. Rotameter is provided to measure actual flow rate. The system is mounted on a table top model with all necessary piping.
-
Product
68HC(S)12 In-Circuit Debugger
ICD12Z
-
P&E's ICD12Z for Windows is a powerful tool for debugging code. It uses the HC(S)12 processor's background debug mode (BDM), via one of P&E's hardware interfaces, to give the user access to all on-chip resources.
-
Product
Pressure Control Setup Using Pid Controller
ULP-26
-
Unitech Scales And Measurements Pvt. Ltd
Unitech’s Pressure Control Setup comprises of Pressure tank fitted with pressure transmitter to measure the pressure. The pressure is controlled by a pneumatic control valve operated by a I to P converter. The whole system is mounted on a Table top Model with all necessary Piping. The electronic panel comprises of ADC/DAC card with RS-232 interfaces.
-
Product
Multi-Axis Vibration Control
-
m+p VibControl provides coupled and uncoupled multi-axis vibration testing (MIMO) in a closed control loop. Test modes include random, sine, shock and time domain replication (road load simulation). Multi-axis motions are characteristic of field environments. The more a vibration test can replicate the field environment, the more realistically it can induce a vibration stress loading equivalent to that experienced by the product in the field.
-
Product
Bench/System/ATE Programmable DC Power Supply Single Or Dual Outputs, 360 To 840 Watts, With Or Without Remote Interfaces
CPX Series
-
PowerFlex design gives variable voltage and current combinations within a maximum power rangeUp to 60 volts and up to 20 amps180 watts or 420 watts maximum per outputIsolated outputs can be wired in series or parallelConstant voltage or constant current operationSettings Locking (S-Lock)PowerFlex or fixed-range operationVariable OVP tripsSelectable remote sense terminalsCompact quarter or half rack 3U case sizeIsolated analogue remote control (CPX400SA only)RS232, USB & LXI compliant LAN (P models only)GPIB Option (P models only)
-
Product
1000A AC/DC Clamp Meter
CM84
-
The CM84 is a high specification 1000A clamp meter, packed full of functions for the installation, testing and maintenance of domestic and industrial installations. It is light enough for easy one handed operation but still robust enough for use in harsh environments.
This compact meter provides accurate measurement of AC voltage to 750V, DC voltage to 1000V and AC current to 1000A. It has the same test functions you would find on a high specification multimeter making this clamp a comprehensive testing solution for electricians, maintenance and service engineers. This has the added benefit of DC current measurement to 1000A and has a useful DC current zero function.
