Charge Amplifiers
A high-gain voltage amplifier with negative, capacitive feedback for converting a charge into a low impedance output voltage.
-
Product
Broadband Amplifier
-
Toellner Electronic Instrumente GmbH
Will reproduce a wide range of signals without significant loss throughout the pass band.
-
-
Product
Linear Amplifiers
-
Advanced Science and Novel Technology, Co., Inc.
Broadband (DC-12GHz) linear amplifier for receiver-side applicationsFeatures controlled gain from 0dB to 31.5dBFeatures input offset adjustment and input peak detectorFully differential input interface with on-chip 50Ohm terminationFully differential output interface with on-chip 50Ohm terminationOutput 1dB compression point of 1.5dBm3rd Harmonic better than -47dBc within the full bandwidth15dB Noise FigureSingle +3.3V or -3.3V power supplyPower Consuption: 530mW typicalFabricated in SiGe for high performance, yield, and reliabilityCustom CQFP 24-pin package
-
Product
Amplifier
-
Toellner Electronic Instrumente GmbH
An electronic device that increases the voltage, current, or power of a signal.
-
Product
Lock-In-Amplifiers
-
Current and voltage inputWorking frequency up to 45 kHzAdjustable sensitivity, time constant and phaseLocal and remote controlCompact and EMI-shielded case
-
Product
4-Quadrant Amplifier
-
Toellner Electronic Instrumente GmbH
A power amplifier that can be operated in all 4 quadrants
-
Product
Limiting Amplifiers
-
Chengdu KeyLink Microwave Technology Co., Ltd.
Keylink's limiting amplifiers use FET device with good consistency and distributed traveling wave amplifying circuit to design. Good amplitude and phase consistency characteristics can be achieved in a wide input dynamic range. It's the key component of the electronic system. Keylink's limiting amplifiers can be categorized as follows.
-
Product
Hybrid Amplifiers
Limiting
-
Macom Technology Solutions Holdings Inc.
MACOM offers a complete line of RF and microwave limiting amplifiers. Our limiting amplifiers use the latest thin film hybrid manufacturing techniques to obtain the highest level of performance, repeatability, and reliability. MACOMs portfolio of amplifiers range from 10 MHz to 4 GHz and are ideally suited for hi-reliability and mission critical applications.
-
Product
Power Amplifiers
-
RPG Medium Power Amplifiers are developed and manufactured by using most modern discrete components and thin film technologies, in order to cover the frequency range 50 to 130 GHz. With improved DC-supply and modern semiconductors these medium power amplifiers not only deliver high power output but also superior power added efficiency (PAE) and higher linearity. These medium power amplifiers are available as a standard product and on request as a customized manufactured product..
-
Product
Hybrid Amplifiers
Gain Block
-
Macom Technology Solutions Holdings Inc.
MACOM’s portfolio of hybrid amplifiers cover a frequency range of 10 kHz to 6 GHz. Each amplifier is designed to be unconditionally stable and have excellent cascadability. Our amplifiers are designed using thin film technology and are integrated components thindat include internal DC biasing circuitry, allowing them to maintain excellent electrical performance over the 55˚C to 100˚C range. Hermetically sealed and screened up to space level, these amplifiers are ideally suited for hi-reliability and mission critical applications.
-
Product
Precision Amplifier
-
TI Precision Labs is the electronics industry's first comprehensive online classroom for analog engineers. The on-demand curriculum pairs theory and applied lab exercises to deepen the technical expertise of experienced engineers and accelerate the development of those early in their career. This free modular curriculum includes over 30 hands-on trainings and lab videos, covering analog amplifier design considerations with online course work.
-
Product
Operational Amplifiers
Op Amps
-
Operational amplifiers, known also as op amps, play a major role in analog signal conditioning applications. Invented by Karl Dale Swartzel Jr. in 1941, these products are largely used in today’s electronic devices.
-
Product
Power Amplifiers
-
Triad’s line of RF and microwave Power Amplifier modules for extended range amplified radio applications set the bar for efficiency, linearity, and size-to-power ratio. We have designed hundreds of COTS modules for exacting frequencies up to 40 GHz . They offer high power levels into the hundreds of watts. And if a standard RF/microwave amplifier design does not fit your exact requirements, we’re specialists in creating custom-modified versions of any of our COTS power amplifier modules.
-
Product
Amplifier
AC-100
-
The voltage amplifier for connecting piezoelectric acceleration meters, microphones, and other primary voltage output transducers to FFT spectrum analyzers with the IEPE standard current output (ZET 017-U2, ZET 017-U8, A19-U2).
-
Product
Transimpedance Amplifiers
-
Advanced Science and Novel Technology, Co., Inc.
Broadband transimpedance amplifier for low noise receiver side applicationsFeatures automatic input offset control and a peak detector8GHz of analog bandwidth for limiting of input data60dB of transimpedance differential gain15pA/sqrtHz of input referred noise density (0.1 to 10GHz)CML output interface with 50 termination and 225mVp-p single-ended swingSingle +3.3V power supplyPower consumption: 250mWExhibits low jitter and limited temperature variation over industrial temperature rangeUnpackaged bare die
-
Product
Power Amplifiers
-
Analog Devices MMIC-based GaN and GaAs power amplifiers cover the low hundred MHz frequency range up through and including components in the W band (75 GHz to 110 GHz). In addition to components, our portfolio also includes GaN-based power amplifier modules with output power exceeding 8 kW. Designed for excellent linearity at high output power, our power amplifiers maintain good heat dissipation and high reliability at elevated temperatures for the wide variety of wired and wireless applications that they are used in.
-
Product
EDFA Amplifier
-
A line of Gain Flattening Erbium-Doped Fiber Amplifiers are designed for in-line amplification of DWDM networks. When a standard EDFA is used to amplify multi-channel DWDM signals, the output power level of various channels will vary according to the gain profile of the erbium fiber. This gain variation can be as great as 6 dB in magnitude. The EDFA-GB-R is unique in its dual-stage amplification and internal Gain Flattening Filter (GFF) to compensate the erbium fiber gain variation.
-
Product
Endevco Cryogenic Charge Output Accelerometers
-
PCB's acquisition of Endevco's full line of testing sensors means all Endevco sensors are now backed by PCB's Total Customer Satisfaction (TCS) guarantee. Endevco® cryogenic piezoelectric accelerometers are built specifically for measuring vibration under cryogenic conditions down to -452° F (-269° C). Signal outputs of these units are very stable even at extremely low temperatures. Their rugged internal construction is designed to withstand multiple cycles of thermal shock with steep temperature gradient. The accelerometers are self-generating devices that require no external power source for operation and contain no electronics. This allows them to operate below the -320° F (-196° C) limit of ICP accelerometers, down to -452° F (-269° C).
-
Product
Isolation Amplifiers
-
Isolation Amplifiers provide power supply designers with a higher performing, single chip alternative to isolation techniques based on optocouplers and shunt regulators. Analog Devices ADuM3190 and ADuM4190 isolated error amplifiers have a 400 kHz bandwidth, with 0.5% typical initial accuracy at 25°C and 1% total accuracy over the extended temperature range of –40˚C to +125˚C. This provides manufacturers of ac-to-dc and dc-to-dc power supplies with a significant upgrade in speed and operating temperature range, as well as a 5× improvement in transient response.
-
Product
Amplifiers
-
Instead of cascading a set of narrowband amps, use a single amplifier from Keysight and enjoy ultrabroad bandwidths - like 0.01 to 26.5 GHz, 0.045 to 50 GHz, and ranges in between. But the best thing about Keysight broadband amplifiers is what they eliminate and reduce: noise, crossover networks, and multiple power supplies.
-
Product
Power Amplifiers
-
In this product category you find highly linear power amplifiers for digital and analog data transmission, power amplifiers for CW applications and for laboratory use, which stand out due to its liability, robustness and long-term availability and which are based on the semiconductor technologies which are actually available on the market.
-
Product
Charge Plate Monitors
-
Our easy-to-use charge plate monitors allow you to accurately evaluate air ionization systems used to neutralize static charge accumulation. Benefit from our economical solutions and products that offer onboard data storage to automate ionization system testing.
-
Product
Amplifiers
-
Packaged and Die up to 26 GHzOver 145 MMIC Surface Mount and Die modelsConectorized models, power output to 100WHigh dynamic range, low noiseLow-cost, custom solutions available!
-
Product
RF Amplifier
SA812
-
Hangzhou Softel Optic Co., Ltd.
SA812 860mhz CATV outdoor trunk amplifier are mainly used for Bidirectional trunk transmission for CATV television image signal, digital TV signal, telephone voice signals and data (or compressed data) signal.
-
Product
Capacitor Charging Power Supplies
-
Lumina Power CCPF and CCHP capacitor chargers utilize the latest innovations in power electronics to deliver clean and efficient energy for pulsed power applications. Learn more about the CCPF and CCHP below.
-
Product
Power Amplifier
-
The Model LN power amplifiers offer extended output power, voltage capabilities, lowdistortion, versatility and the latest BJT power in the operational amplifier technology. All theseperformance features are not available in other power amplifiers.
-
Product
Gain Block Amplifiers
-
Qorvo designs and manufactures a wide selection of general-purpose, internally matched MMIC amplifiers that are targeted for many applications in network infrastructure and defense / aerospace. These components showcase the wide range of performance capabilities using Qorvo's processes. Our general-purpose gain blocks are internally matched and offer various gain and linearity levels in a variety of package types, giving customers many options for system design.
-
Product
Amplifiers
-
Amplifiers are used to amplify the energy output of photodetectors as well as convert their electrical signal for a number of illumination measurement or spectroscopy applications. Amplifiers are digital systems that amplify the low electrical current transmitted by photodetectors to easily detectable levels. Amplifiers also convert photodetectors' electrical current into voltage so that their signal may be read by other digital devices. Amplifiers are indispensable for nearly any light measurement applications by greatly increasing the usability of a detector system.
-
Product
6-Channel SD/ED/HD Video Filter With Charge Pump
ADA4424-6
-
The ADA4424-6 is a high performance video reconstruction filter specifically designed for consumer applications. It consists of a standard definition (SD) section with two fifth-order Butterworth filters, and a high definition (HD) section with three fifth-order filters. The SD section contains an internal Y/C summer for CVBS output, whereas the HD section provides selectable corner frequencies for either extended definition (ED) or HD signals.
-
Product
InfiniiMax III+ Series Probe Amplifier, 4 GHz
N2830A
Amplifier
The N2830A Series InfiniiMax III+ probing system is the next generation of InfiniiMax probing, greatly expanding the measurement capability and usability of a probe capable of measuring all components of a differential signal. The built-in InfiniiMode technology allows customers to switch differential, single-ended, and common mode without adjusting probe tip connections.
