Charge Amplifiers
A high-gain voltage amplifier with negative, capacitive feedback for converting a charge into a low impedance output voltage.
-
Product
GN Range Broadband Power Amplifiers 100 KHZ - 200 MHZ
GN Series
-
Class A solid stateBroadband (instantaneous single band): 100 kHz 200 MHzTypical output power : 500 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 450 W and H < -20 dBc up to 100 MHz andP1dB > 180 W and H < -20 dBc from 100 MHz to 200Air cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Rack3 years standard warranty
-
Product
Charge Coupled Device (CCD) Standard Image Sensors
-
Teledyne e2v is the leading supplier of scientific grade Charge Coupled Device (CCD) image sensors for the most challenging low light imaging and spectroscopy applications.
-
Product
MOSFETs For High Frequency Amplifier
-
The MOSFETs shown below are best suited for amplification of high-frequency signals.
-
Product
MOSFETs For Amplifier
-
These are enhanced power MOSFETs with excellent frequency characteristics. They are ideal for audio amplifier output.
-
Product
Power Amplifier
DPA8-0.4-22G-2032
-
Power Amplifier, Frequency 0.4~22GHz, Gain 40dB, Psat 30dBm, SMA Female
-
Product
RF Signal Amplifiers
-
The A10200 RF amplifier was designed to extend the power range of the Tabor arbitrary waveform generators and RF signal generators, yet it is compatible with many signal sources instruments.
-
Product
Reference DAC, Pre And Headphone Amplifier
CALLIA
-
Designed and manufactured in the United Kingdom, CALLIA embodies the Prism Sound uncompromising approach to audio resulting in the most accurate and detailed DAC available.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Amplifiers
-
Fully automatic, legal limit plus headroom amplifierAlpha’s low-drive, tube amplifier design delivers the cleanest possible signalOperates on all Amateur Radio Bands 160M thru 10MSingle, easy to find, inexpensive 3CX1500A7 8877 type tubeInternal, automatic 4 port antenna switch capable of combining any 2 antenna portsAlpha’s Legendary service and support4 year limited warranty on hardware, 1 year on tube1500W, 100% duty cycle, no time limitation, key down foreverRugged construction built to last
-
Product
Amplifiers
-
Monacor International GmbH & Co.
Amplifier technology from MONACOR supports you in many areas. You can use loudspeaker systems or electro-acoustic systems with our amplifiers perfectly, even in large buildings. Depending on the model selected, our amplifiers and power amps are also designed for PA systems or hi-fi devices. You will also find stereo amplifiers for car hi-fi in our range. All amplifier models are designed for reliable performance in professional and private use. Like all MONACOR products, this item also combines the perfect combination of low price and high performance.
-
Product
SV Range Broadband Power Amplifiers 0.8 GHZ - 3.2 GHZ
SV Series
-
Class A solid stateBroadband (instantaneous single band): 80 MHz 1000 MHzTypical output power : 100 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 100 W and H < -20 dBc up to 450 MHz andP1dB > 65 W and H < -20 dBc from 450 MHz to 1000 MHzAir cooling: self contained fansCan operate in full mismatch conditions without damageUpgradable to MT 200 possibleReliable, efficient and robust19" Rack3 years standard warranty
-
Product
4-Quadrant Power Amplifier
PAV10000
-
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
Product
High Voltage Amplifier
HA-805
-
*800Vp-p(±400V DC) *200mAp-p(±100mA DC) *Bandwidth: ≦300KHz(400Vp-p) *Slew Rate: 300V/us *Gain(AMPL):0~180(10 Turn VR) *DC Offset: ≦0~±400V(10 Turn VR+SW) *Output Resistor: 100Ω *Microprocess Control Protection
-
Product
3-Ch Sensor Amplifier
PS-1300
-
The PS-1300 3-Ch Sensor Amplifier is designed to be compact and light weight, and able to be used in combination with a tri-axial accelerometer. Each channel can also be used independently and connected with a single axis accelerometer. The PS-1300 has built-in integration function and enables to optimize the input signal to vibration data analysis devices connected.
-
Product
Saluki SE2041 DSP Lock-In Amplifier
-
SE2041 Digital Lock-in Amplifier provides an excellent performance within its bandwidth from 1 mHz to 60 MHz. With the advantage of the latest digital signal processing technology and high-speed 250MSPS 14-bit ADC, SE2041 can easily detect the phase and the magnitude of weak signals overwhelmed by various large noises. The performance of SE2041 is as good as other lock-in amplifiers all over the world, even better than them in some certain parameters, such as measurement accuracy, SNR, dynamic reserve, which meets the needs of scientific research and industrial application well.
-
-
Product
Microwave Amplifiers
MShU Series
-
*Ultrawide Operating Frequency Range*Small Size*Low Noise Figure*Low Power Consumption
-
Product
Scienlab Charging Discovery System (CDS) – High-Power Series
SL1047A
Battery Test Platform
The Scienlab Charging Discovery System – High-Power Series from Keysight enables you to test charging interfaces of electric vehicles (EVs) and EV supply equipment (EVSE) during high-power charging up to 1,500 V DC and ±600 A DC. With the CDS can perform all necessary conformance and interoperability tests according to worldwide charging standards. Our new solution, which features the separate Scienlab Cooling Unit with interchangeable liquid-cooled charging adapters, also enables a high-power upgrade of the SL1040A Scienlab Charging Discovery System - Portable Series.
-
Product
Charge Plate Monitor
-
The electrostatic resistance of electronic devices is declining, and the number of ionizers installed is increasing. Ionizers cause deterioration of static elimination performance and imbalance of ions due to dirt and wear of the discharge electrode needle. Charging of electronic devices is also caused by ion blow. of an ionizer that is out of balance due to dirt and wear, and reaches a level that destroys advanced electronic devices.The atmospheric ion monitor measures the potential of the charging plate (detector), which has almost the same capacitance as the device's ground capacitance , with high accuracy, and is the most suitable measuring instrument for checking the effect when installing the ionizer and for daily management.
-
Product
Amplifiers
LA-1K
-
Introducting the new LA-1K RF Sensing Dual HF LDMOS 1000 Watt Amplifier. While the LA-1K will work with a wide variety of tuners and transceivers, Palstar custom-designed the LA-1K to work as the perfect match for our very popular HF-AUTO autotuner. MADE IN THE USA
-
Product
DC-Coupled Pulse Amplifiers
-
These DC-coupled pulse amplifiers are available in a simple DC-power module format, and are also available in an AC-powered benchtop instrument format. All models will drive a 50 Ohm load.
-
Product
Reference plus Comparator or Amplifier
-
Analog Devices reference plus comparator or amplifier products combine the excellent initial accuracy and low overtemperature drift performance of single function voltage references with comparators, buffer amplifiers, and current sense amplifiers. These products offer compact solutions for a broad range of applications such as battery monitoring, threshold detectors, window comparators, auto power-off circuits, and low dropout (LDO) regulators.
-
Product
Transimpedance Amplifiers
-
Artifex Engineering GmbH & Co. KG
Applications include photodetection with PMTs and photodiodes, spectroscopy, Scanning Tunneling Microscopy, ionization detectors, pyro and piezoelectric detectors.
-
Product
Headphone Amplifiers
-
A top-of-the-line headphone/earphone amplifier designed for precise professional audio monitoring.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Low Noise Amplifiers
-
High-intercept and high-gain low noise amplifier modules. Wide supply voltage range. Custom designs available through LNA design services.
-
Product
RF Amplifiers up to 2500 MHz
-
L and S Band 1,2,4, and 8 Kilowatt rack mount solid state microwave amplifiers ideal for CW and pulse TWT amplifier replacement utilizing GaN technology and rivals the TWT amplifier in size and weight. Also available is our broad line of high power modules including 25, 50, and 100 watt pallets for integrating into your own power amplifier design.
-
Product
Thermocouple Interface Amplifiers
-
Analog Devices offers specialized precision thermocouple interface amplifiers that provide a simple and effective solution for measuring thermocouple temperatures. With features such as integrated cold junction compensation and a high gain precision instrumentation amplifier, these thermocouple amplifiers provide a complete signal conditioning system in one IC package. ADI’s thermocouple amplifiers are suitable for use in diverse environments to measure a wide range of temperatures. These products will save you in cost, space, and unnecessary circuit design across a broad range of applications and industries.
-
Product
Power Amplifiers
-
Amplifiers with Extron patented CDRS™ – Class D Ripple Steering technology which supports high signal fidelity and clear audio.
-
Product
WaveLink ProBus2 Platform/Cable Assembly for 4-8 GHz WaveLink Amplifiers.
WL-PBUS2
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
