Interconnect Stress Test
accelerated test of PCB pads, lines and thru-holes.
-
Product
Interface Test System (ITS)
-
The SecuControl ITS is a modular test block designed to meet the stringent safety, reliability, and performance needs of IEC-based substations. With fully finger-safe construction, keyed STP test plugs, and built-in CT Shorting, the ITS enables safe, repeatable secondary injection testing, without the risk of open CT circuits or accidental trips. It is the ideal solution for structured, standardized testing across protection systems.
-
Product
Corrosion Test Chamber
CME SF-CCT
-
CME SF-CCT chambers are designed to be flexible enough to comply with as many different CCT specifications as possible. These may be programmed to conduct a whole range of corrosion tests such as wet cycle, dry cycle, controlled humidity as well as the salt spray test in a single chamber. This can occur in any sequence and be repeated automatically. A wide range of optional accessories enable additional climates to be added to further extend the number of climates and conditions that can be created.
-
Product
Test Handlers
-
Boston Semi Equipment test handlers are designed for optimum production performance on your test floor.
-
Product
Milliampere-Level Test System
-
Shenzhen Sinexcel RE Equipment CO., Ltd
mA class battery test system, mainly used for battery material research, high-precision test, pulse charge and discharge test, DCIR test, cycle Life test. It provides powerful testing equipment for research institutions, universities and experimental centers of battery production enterprises
-
Product
Textile Testing Equipment
-
Manufacture and supply a wide range of textile testing equipments. Our machines all meet with: ISO, ASTM, AATCC, BS, EN, DIN, JIS and other requireable standards. Yarn, Fiber and fabric testers. Strength, Abrasion, pilling, flammability fatigue, peeling, appearance, etc. testing.
-
Product
Pre-compliance Testing
-
SILENT offers pre-compliance testing for products with planned distribution to commercial and industrial markets in the US and overseas. This includes testing to ensure that emissions, immunity, and circuit-to-circuit interference problems are discovered early and immediately brought under control. We use the most advanced EMC and RF test & measurement equipment and diagnostic software available from leading suppliers.
-
Product
Optical Loss Testing
-
Is to inject a known level of light in one end and measure the level of light at the other end, using an OLTS. The difference between source and receive power levels is the loss.
-
Product
HV Test Set
-
Beijing GFUVE Electronics Co.,Ltd.
Used for testing transformer, circuit breaker & switch etc by engineer, for example TTR tester can test transformer turns ratio.
-
Product
Sanity Testing
-
TestOrigen Software Testing Services Pvt Ltd.
Sanity testing is basically a part of regression testing that is performed for finding the minor bugs and new build up errors after testing the whole software development lifecycle. Sanity Testing ensures that the system is ready to test.
-
Product
EMC/EMI Testing
-
MET Laboratories boasts proven, superior capabilities in Electromagnetic Compatibility (EMC) compliance testing, including wireless & RF testing. Our EMC labs are among the most respected in the U.S. Our EMC testing covers FCC Part 15, as well as Parts 18, 22, 24-27, 74, 90 & 95, and 101
-
Product
160MHz Test System
IQxel-MW 7G
-
Platform solution for 802.11 a/b/g/n/ 802.11ac, 802.11ax, and 802.11be testing in the 2.4 and 5 GHz and 6 GHz bands and the most popular wireless connectivity standards (Bluetooth®, Bluetooth® 5, Bluetooth® 5.1, Bluetooth® 5.2, Zigbee, Z-Wave) as well as LPWAN technologies (Sigfox, LoRa).
-
Product
Test Automation Solution
-
Ready-to-use test frameworks and bot-based test automation solutions to assess your apps’ consistency, usability, performance and content in both test and live conditions.
-
Product
Testing Solutions
-
Within the test strategy the final functional test complements the quality strategy. Therefore meaningful results of functional tests shouldn't be focused only on good/bad selection. Goal is to get correct data for statitistics and trend analysis.Under economical point of view you should consider following points as very important in test conceptions:Stability of measurementsAccuracyand the throughput
-
Product
Shock Testing
-
Shock testing typically involves calibrated, repeatable, violent events. The resulting energy is then absorbed transferred through the test specimen or Device Under Test (DUT)
-
Product
Off-Air Testing Products
-
Understanding the challenges of the Electromagnetic Spectrum is paramount for Engineers that are charged with the design, characterization, validation of modern RF systems such as Communications Systems, RADAR Systems, and Electronic Warfare Systems.
-
Product
Test Automation
-
Test automation helps in reducing regression testing time and cutting down the time to market with significant cost savings on long term basis. However, a clear automation strategy and roadmap is key to ensuring the right return on investment on your automation initiatives. With disparate application architecture, multiple environments, third party integrations and multiple user devices, a standardized and consistent automation approach is needed to ensure high reusability, ease of maintenance and lower upfront cost.
-
Product
CAM/TRAC Test Kits
Series 431
-
Series 431 GR2270 ‘Z’ Axis Camtrac Dual Well Mechanical Test Kits.
-
Product
ESD Device Testing
-
Barth Electronics, Inc. offers complete ESD Testing to the semiconductor industry. Nothing is outsourced – all testing is performed at our factory in Boulder City, Nevada.
-
Product
Test Solutions For Integrators
-
Beyond being your test equipment expert, Testek can also provide engineering design advice and guidance on building complete test solution facilities. We will work closely with your building contractor to advise on the most optimal layout configuration and to specify all facility resource requirements. For systems that may share resources, we can facilitate resource demand and management, including power management and fluid management. With a central control system, we can provide software logic to monitor these resources and route them appropriately based on demand and priority.
-
Product
Services, testing
-
They are particularly the voltage tests, power, mechanical and electrical durability tests as well any verification of the LV and MV switchgears including the type tests.
-
Product
D-Mic Testing System
BK3012V2
-
Easy to use and faster than human testers can load, the new BK3012V2 is the upgrade of our popular BK3012 D-Mic tester. Setup is even easier than for the BK3012 and you can enter specifications and be ready for testing in a few minutes. As well as testing, the BK3012V2 can be connected to a computer, so you can keep your results and analyze them for current quality and trends over time.
-
Product
Test System
DA-1 ATS
-
The DA-1 ATS is an economical Commercial-Off-The Shelf (COTS) build-to-print tester. The test station is compliant with the published drawing package. The system does not include software.
-
Product
Test Contactor/Probe Head
Hydra
-
Engineered for excellence and efficiency, Hydra™ spring probe series offers precision, reliability, and standardized semiconductor test interface.Designed to be best-in-class at a competitive price point, Hydra is optimized to maximize your operational efficiency. Hydra is built to withstand demanding high-volume manufacturing test environments with its robust and durable design.With a common test-height, Hydra offers the ability to mix and match power, RF, and Kelvin probes within the same test socket. In addition, Hydra streamlines inventory management with fewer probe part numbers to manage and shorter lead times.
-
Product
Test & Measurement Assemblies
-
Test & Measurement cable assemblies for a variety of applications
-
Product
Electrification Testing Solutions
-
When looking for a partner to assist with your electrification testing or power electronics testing challenge, Ball Systems has the expertise and experience to ensure your energy storage or power conversion project moves forward efficiently.
-
Product
Ozone Test Chamber
EKT-2001OZ-HPSSX
-
Designed and manufactured in accordance with ASTM D1149, ISO1431 & JIS K6259 standards. Providing precise and accurate ozone (OZ) concentration environment for rubber and polymer test. Widely applied to (1) Accelerated ageing research (2) Quality control and assurance tests and (3) R&D laboratory formula experiments for cracking resistance.
-
Product
Ventilation Test Instruments
-
Our instruments are optimized for ease-of-use, yet offer a range of advanced capabilities including data logging, that are critical in ensuring quality commercial ventilation.
-
Product
Terminals And Test Points
-
Today's high tech electronics require space saving, low cost methods for connecting and testing circuitry. Our complete line of Quick Fit terminals, Screw Terminals, Solder Lugs and Test Points and Jumpers are designed to meet the interconnect and testing challenges for electronic and electrical component termination points.
-
Product
Manual Testing Services
-
Production teams often refer to automation testing like it’s the holy grail. But when it comes to user experience, there’s no replacement for the human eye. While automated tests focus on repetitive tasks, manual QA testers come up with creative use cases and provide a lot more value. Very often, our recommendations helped improve the products and even lead them in new, more successful directions.
-
Product
Optical Test And Measurement
-
Any type of fiber optic interconnection requires its interfaces to be free of dust and scratches in order to reach the lowest transmission loss. Small, handheld and battery powered inspection tools are available from AMS Technologies for inspection of fiber optic connectors in the field as well as high resolution type microscopes suitable for use in a production environment for qualifying the endface preparation. Additional S/W tools can support the user in making a quick decision if a certain defect is acceptable or if the surface fault disqualifies it for further use. Small and lightweight test equipment for measurement of the transmitted power in an optical fiber is needed wherever technicians handle optical fibers. Our product portfolio comprises light sources for various wavelengths, power meters for the visible and infrared and integrated solutions for sources and meters as well as optical time domain reflectometers (OTDR) coupled with visible wavelength light sources for easy fault detection within a fiber optic link.
