Sensors
detect a physical event then translate to a representative analog signal.
See Also: Measurement, Detectors, Meters, Transducers
-
product
Inspection and Maintenance
Sensors' EMISSIONS INSPECTION ANALYZERS have a long-standing history for exceeding international standards with compact, portable, and cost-effective systems.
-
product
PCI Precision Resistor Card 3-Channel, 3Ω To 22.3MΩ
50-297-154
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Wattmeters
Monitor 4 sensors simultaneously for peak, Average power and coax SWR. Direct USB 2.0 full speed interface. Backlit LCD display for stand-alone operation- Your PC is optional. Oscilloscope and Spectrum Analysis of the RF Modulation- Observe IM and "Splatter" frequency components realtime. Complete system includes (1) sensor, WN-2 unit, AC power module and software on CDROM. Wide range of sensors cover 100 milliwatt to 8KW, 1.6 Mhz to 470 Mhz.
-
product
PCI High Density Pecision Resistor Card, 4-Channel, 2.5Ω To 925Ω
50-298-121
The 50-298-121 is a high density programmable resistor card with 4 channels which can be set between 2.5Ω and 925Ω with 0.25Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Digital Ultrasonic Maintenance System
VPE-2000
The Superior AccuTrak VPE-2000 is the first digitally controlled ultrasonic detector. Like two instruments in one it uses two independent sensors supported by separate electronic circuits configured specifically to their own sensor. This assures optimum sound clarity and frequency response. When switching between the airborne and contact sensors all settings are retained in memory! Digital LED meters let you establish baselines, perform trending, and accurately repeat these tests better than older more expensive analog instruments.
-
product
SparkFun Sensor Kit
Do you have a good understanding of various sensors or need a variety of them for a project? The SparkFun Sensor Kit includes a sensor for just about every job. With everything included in this kit, you'll be able to sense gesture, humidity, temperature, motion, touch, sound, altitude, acceleration and more! These are some of our favorite sensors from each category. But wait, there's more! The SparkFun Sensor Kit now includes several of our sensor boards that feature the Qwiic Connect System for rapid prototyping!
-
product
Sunshine Duration Sensor
SD4
Four identical omni-directional sensors under a hemispherical shading canopy. Embedded microcontroller executes a sophisticated contrast-evaluation algorithm to accurately discriminate direct sunshine from diffuse sunlight.
-
product
Inline OEM High Resolution Thickness & Resistivity Module for PV / Solar Sorters
MX 152
To allow three thickness scans during belt transport at different wafer sizes, two measuring bars, one from top and one from bottom, hold 3 sensors each.
-
product
Pitot Static Tester / AoA TESTER
ADSE 744
This tester was specifically designed for the new-generation pitot tubes that integrate sensing probes, pressure sensors and powerful air data computer processing to provide all critical air data parameters including Pitot and static pressure, airspeed, altitude, and angle of attack. This Pitot Static tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems. The AoA Channel behaves as a second Ps channel, in order to creat...show more -
product
Crack Testing
STATOGRAPH® Product Family
Foerster Instruments, Incorporated
The STATOGRAPH product family is used for testing surface cracks with the help of eddy current sensors. Eddy current testing for material cracks requires the appropriate evaluation electronics and probes adapted to the testing task. Depending on the test situation and test object, the STATOGRAPH family of test instruments offers the right system for this purpose.
-
product
Magnetoresistive Milligauss Meter
MR3
The MR3 Magnetoresistive Milligauss Meter measures and displays the three vectorcomponents (X, Y, Z) as well as the magnitude (M) of the static magnetic field. Update is two times per second. The three sensors are in a 25 mm (1") cube at the end of a flexible 100 cm (40") cable. It can be powered by 4 AA batteries (included) or a Worldwide AC adaptor (included). It can collect and store data (X, Y, Z and M) for later download or stream data live via USB connector. Both the instantaneous values o...show more -
product
Low Profile PCI 24 Channel TTL Digital Interface
8018
The 8018 Low Profile PCI digital I/O interface provides 24 channels of buffered drive digital I/O emulating 8255 mode zero. The board can be utilized for PC-based control and automation of equipment including sensors, switches, security control systems, and other industrial automation systems.
-
product
Pole Detectors
The tip of the unit detects the field polarity. The magnet surface is placed parallel to the unit tip. Two 1.5V AA battery operated. Power ON Switch activates the sensors and gives visual indication in form of two LEDs placed on the arm of the unit.
-
product
Pressure Sensors
The output voltage changes with the absolute pressure applied to the pressure port. The gain, offset and thermal drift of the pressure sensor is digitally compensated to minimise errors and to create a single-ended, amplified output in the 0 to 5 Volt range.
-
product
Sensors And MEMS Test
Easy docking and undocking of the MEMS modules to the standard test handler whether Gravity, Pick and Place or Test in StripTest in the complete tri-temp range for ambient, hot and cold (automotive certified)Easily convertible to other packagesDownscaled stand-alone engineering set-up availableGlobal support by experienced Cohu Field Service and Applications staff
-
product
TMR Switch Sensors
MultiDimension Technology Co.,Ltd.
A digital unipolar magnetic switch that integrates TMR and CMOS technology in order to provide a magnetically triggered digital switch with high sensitivity, high speed, and ultra-low power consumption. It is designed for use in applications that are both power-critical and performance-demanding. It contains a push-pull half-bridge TMR magnetic sensor and CMOS signal processing circuitry within the same package, including an on-chip TMR voltage generator for precise magnetic sensing.
-
product
PXI 2.5W Programmable Resistor Module, 8-Channel, 1Ω to 62.1Ω
40-251-011
The 40-251-011 is a programmable resistor module with 8 channels which can be set between 1Ω and 62.1Ω with 0.25Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
Data Logger
MS6D
Data loggers are designed for measuring, recording, evaluation and subsequent processing of input electrical signals, which are subject to relatively slow changes (> 1s). In conjunction with the appropriate sensors and transducers are suitable for monitoring physical quantities.
-
product
Visibility Sensors
Campbell Scientific offers visibility sensors that use infrared forward-scatter technology. These sensors report meteorological observable range (MOR) for fog and snow. Visibility sensors are often used in road, marine, aviation, and wind-energy applications.
-
product
Integrated Systems
Innerspec’s Integrated Systems are designed to provide automated and semi-automated NDT inspections in factory environments. These systems can incorporate unique sensors, instrumentation, software, as well as customized mechanical devices to integrate the inspection system with other equipment and processes.
-
product
Wireless Hazard Monitoring
When it comes to hazard monitoring, we know it simply has to work. HazardPRO was designed from the ground up to provide turnkey, reliable, and consistent protection for your most valuable assets—products, facilities, and most importantly, people. Consistent operation is ensured with built-in tools such as self-diagnostics, transmission logging, and redundant radios providing you confidence that your critical processes are being monitored and logged at all times. Wireless nodes utilize temperature (bearing, ambient, and stud), RPM shaft speed, alignment, and vibration sensors. Ambient Sensors ensure bearing and alignment measurements are relative to the surrounding environment.
-
product
Multiparameter CTD with a Wide Choice of Standard Sensors.
MIDAS CTD+
Featuring Valeport’s latest 400 Series electronics, the CTD+ will sample all fitted sensors at exactly the same instant, at up to 8Hz. Advanced setup software allows a variety of sampling regimes including burst modes, delay starts and conditional sampling. Available with up to 64Mbyte memory and internal battery pack, as well as a selection of real-time output formats, the CTD+ may be used with Valeport’s own water bottle carousel.
-
product
Relative humidity, temperature sensors
T3111
Relative humidity, temperature sensors at probe on 1 meter cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
PCI Precision Resistor Card 4-Channel, 2Ω To 102kΩ
50-297-134
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Luminescence sensors
Leuze electronic GmbH + Co. KG
Luminescence sensors detect both visible as well as invisible luminescent markings. They send the result as switching output or analog value and are used primarily for sorting and inspection tasks in areas in which other detection methods fail to supply reliable results or where the markings should not or must not be visible. Luminescence sensors are available for various luminescence colors and feature operating ranges up to 200 mm and have a very compact metal construction. The sensitivity adjustment is performed via potentiometer. Turnable M12 connector.
-
product
Ultrasonic Sensors
Chemically resistant ultrasonic sensors measure fill levels without contact both under normal pressure and at an overpressure of up to 6 bar in tanks and containers. Through the combination of switching and analog output, you can even conduct fill-level and overflow protection simultaneously.
-
product
Photoelectric Sensors
Our broad range of photoelectric sensors is aimed at all automation solutions where noncontact object detection can be utilized. The wide variety of different operating principles, models, sizes and specifications means that the best possible sensor can always be found for the relevant application and all conditions that occur in practice can be met.
-
product
PCI Precision Resistor Card 6-Channel, 3Ω To 2.97MΩ
50-297-051
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Washwater Monitoring System
EG-100
Washwater Monitoring System for NOx and SOx Scrubber.Monitoring pH/Temperature, Turbidity, and PAH.EG-100 has flow type sensors.