Digital Input-Output
Input/output of digital values.
-
Product
Digital RCD Testers
-
Used to detect whether the RCD in the circuit can be triggered normally.
-
Product
5 Digit Frequency Meter
CS1-F
-
CS1-F economic type Frequency Meter is designed with high accuracy measurement, display and communication of Frequency.The innovation feature is auto-range input from 0.01Hz~100KHz(option ~140KHz) and the display resolution will auto-change to show the highest according to input frequency.They are also available 1 option of 1 Relay outputs, 1 Analogue output or 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission or communication for a wide range of panels and testing applications.
-
Product
Digital Superficial Rockwell Hardness Tester
900-348
-
This digital Superficial Rockwell hardness tester with fully automated load/unload procedures affords highly sensitive and accurate readings. Micro computer controlled with USB output to built-in mini printer or PC. The 900-348 digital superficial Rockwell hardness tester offers programmable scale conversions, dwell times, statistical capabilities and test counter. Capable of testing in all of the superficial Rockwell® scales.
-
Product
PCI Direct Digital Synthesizers
SYNTH300-TRIG-HS
-
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.
-
Product
Digital Liquid Mass Flow Meters / Controllers
LF-F/LV-F Series
-
The LF-F and LV-F Series are digital liquid mass flow controllers using a Peltier element which cools the liquid rather than using the more common method of thermal heating. This technique removes the risk of boiling chemicals with a low boiling point, thus allowing for greater chemical control.
-
Product
4 Digit Temperature Meter (5 Channels)
CM1-TX5
-
RS-485 Modbus RTU protocol (with communication LED indicator)RS-485 address 1~255Communication Baudrate 9600, 19200, 38400, 57600, 115.2KParity check N81, N82, E81, O81Input 5 channels of signal selectable：thermocouple/PT100.5 channels of input can be set to play 1~10 seconds loop display.1~5 channels of display value limits can be set, and the number of channels of carousel display screens can be set by yourself.5 channels of input signals with LED unit cycle display.Standard 2 groups of alarms Hi, LO with communication LED indicators to ensure the normal operation of the field system.Suitable for HVAC refrigeration and air conditioning PLC, DDC, PC brands to achieve remote real-time monitoringCan be used in solar panels, medical control, clean room, ice water host, boiler, motor, chemical plant, power plant, school energy-saving control, remote control of power monitoring panel
-
Product
4 Digit Handheld Multimeters
U1240 Series
-
The Keysight U1240 Series delivers strong and solid digital multimeter (DMM) test equipment, providing the performance functionality you need to work efficiently on the bench or in the field. The IP67-certified U1240C model can withstand drops up to 10 feet (3 meters) and work longer for you with up to 400 hours of battery life.
-
Product
Digital Multimeters
-
Uncompromised Performance in laboratory-grade Digital MultimetersBasic 5.5 digit DMM, 5.5 digit DMM with LXI, and full 6.5 digit DMM models available
-
Product
Handheld Digital Multimeter, 4 digit, with IP 67
U1241C
Digital Multimeter
The strong and solid U1240C Series handheld digital multimeters (DMMs)are the tools technicians or industrial test engineers use to perform their work confidently and efficiently. Designed for handheld users working in various environments, the U1240C series is certified to IP 67 and capable to withstand up to 3-meter (10 feet) drop to suit harsh working environments. The U1240C handheld DMMscan even work longer for you with up to 400 hours of battery life. With the built-in LED flashlight, the U1240Chandheld DMMsallow users to single-handedly illuminate test area.
-
Product
Digital Vibration Control System
DSC-98000MJ
-
The DCS-98000MJ series vibration control system is the most suitable digital vibration control system used for an electrodynamic vibration testing system to perform vibration evaluation test for highly advanced industrial products. The system is a highly stable Embedded Computer based system, the computer on which the Intel® Celeron™ Processor is installed. It consists of the vibration control, the communication Dynamic Control Unit (main DCU), and the expandable measuring input/output Dynamic Control Unit (sub DCU).
-
Product
Digital High Voltage Meter
-
AllWin Instrument Science and Technology Co., Ltd.
Voltage, is 4 1 / 2 digital displayTrue RMS measurement High accuracy and stableSuitable for all waveform measuremen
-
Product
Digital Storage Oscilloscopes
SDS1000CML+ Series
-
SDS1000CML+ series is a dual-channel universal digital oscilloscope, available in 70, 100, and 150 MHz bandwidth models. It includes a 2 Mpts memory depth that helps to ensure accurate waveform resolution and to capture longer signal lengths. With its 7-inch TFT-LCD (800*480) screen, there is adequate screen space to help better see and analyze waveform details. Along with a 1 GSa/s sampling rate, the SDS1000CML+ supports 32 parameters measurements and common mathematical operations to speed up complex / repetitive measurements.
-
Product
Digital I/O Module with 32 24V/0.5A outputs
IO205
-
This I/O module is a dedicated digital I/O module providing 32 channels of 24V/0.5A outputs. The digital outputs are also galvanically isolated by opto-couplers. All outputs are protected against short-circuit and thermal overload and can output up to 0.5A per channel.
-
Product
PCI 96 Channel TTL Digital Interface
8009
-
The 8009 digital I/O interface provides 96 channels of buffered drive digital I/O emulating 8255 mode zero, which can be utilized for PC based control and automation of equipment including sensors, switches, security control systems, and other industrial automation systems. 10K pull-up resistors are included. Optional values are available.
-
Product
Digital Battery Load Tester
DBT125
-
Battery load test. Depending on the size of the battery, this product adds a very high load to the battery (125 A). It enables the reading of battery condition by voltages and by its ability to maintain the load, thus determining levels of sulphation.
-
Product
Intelligent Digital Gauss Meter / Tesla Meter
DX-160
-
DX-160 Full-digital high-precision gaussmeter/teslameter is designed for high-test precision, high-resolution magnetic field test applications. It provides a wide-range measurement from DC to up to 50kHz AC magnetic field measurement.
-
Product
Digital Signal Processing
ITA
Digital signal processing routines can be conducted on raw signal data acquired by GaGe high-speed digitizers either directly on the onboard FPGA of the digitizer card via our eXpert FPGA firmware features or can be optionally conducted on GPU cards receiving real-time streaming of raw signal data acquired by GaGe high-speed digitizers via the PCIe interface.
-
Product
Digital Display Auto Torsion Testing Machine
NJS Series
-
Jinan Testing Equipment IE Corporation
NJS Series Digital Display Auto Torsion tester is designed and built for torsion test on metal & non-metallic materials, as well as parts & components. NJS is loaded through the rotation of the active cartridge driven by the AC servo motor and cyclonical pinwheel reducer motor. The torque and torsion angle are measured respectively by the high-precision torque transducer and photoelectric encoder. The digital torsion testing machine is an essential instrument to inspect torsion properties of materials for mechanical laboratories of aviation industry, construction industry, scientific research department, universities and industrial enterprises.
-
Product
JTAG/Boundary-scan Digital I/O Module
ScanIO-300LV
Digital I/O
The ScanIO-300LV JTAG/boundary-scan digital I/O module turns an IEEE-1149.1 boundary-scan controller (such as the Corelis PCI-1149.1/Turbo or NetUSB-1149.1) into a powerful digital interconnect and functional tester.
-
Product
Digital Readouts & Metrology Tools
-
HEIDENHAIN digital readouts have universal applications. In addition to standard tasks on milling, drilling and boring machines and lathes, they also can be used with machine tools, measuring and testing equipment, and special machines in fact, they can be used with any machine where axis slides are traversed manually.
-
-
-
Product
Digital I/O Products
-
Digital I/O series products provide computer monitoring of digital input and digital output signals for control of industrial devices through solid state relays.
-
Product
Digital Mass Flow Controller
SEC-N100 Series
-
The SEC-N100 Series is suitable for a large variety of industries and applications. This mass flow controller can control a wide range of flows: from 10 SCCM to 1000 SLM. The SEC-N100 Series also has various types of communications available i.e. digital/analog, DeviceNet™, CC-Link®, PROFIBUS™, and EtherCAT®. The SEC-N100 Series offers high accuracy (+/- 1.0% S.P. *1) and high-speed response. This mass flow controller also has multi-gas/multi-range function emphasizing its' cost reduction capabilities in your process.
-
Product
Digital Meteorological Sensor
ZET 7023
-
The ZET 7023 weather sensor is a measuring unit with two in-built sensors one of which is responsible for measuring relative humidity and temperature, and the other one, for atmospheric pressure measuring.
-
Product
Digital Indicating Pressure Transmitter
DSGT
-
Series DSGT Digital Indicating Transmitter is a versatile multi-function process gage that features an excellent 0.25% full scale accuracy.
-
Product
Digital Torque Meter Torsion Tester
HN-1E~20E
-
Shenzhen Chuangxin Instruments Co., Ltd.
Digital Torque Meter is an intelligent metrologic instrument, which is designed for various torque test and calibration. It's mainly used for electic/manual torque drive, torque screwdrivers, bolt driver, tension wrench and other testers and products which refer to tightening force. It is widely applied in these industries, such as electrical manufacturing, machine manufacturing, car light industry, professional research and tests, and so on.
-
Product
Digital Generator
ZET 7160-G
-
ZET 7160-G is a single-channel digital generator capable of changing the duty ratio from 0 to 100%.
-
Product
Digital Mission Engineering
-
From chip to mission, connect modeling and simulation efforts across all phases of the engineering product life cycle. Model multi-domain operational environments, including land, sea, air and space, with accurate, dynamic, physics-based simulations. Integrate with the Ansys portfolio of multi-physics tools and solvers to achieve unmatched end-to-end modeling and simulation.
-
Product
Digital Transformation
-
Digital Transformation is the combination of digital technology into all fields of business. It’s fundamentally changing how companies monetize, create, and defend value, giving companies a competitive edge. The drive towards digital transformation presents businesses with one of the most outstanding opportunities. Though it may be difficult to define the term ‘digital transformation’, from a wider prospect, it can be defined as a combination of digital technology into various areas of a business.
