Particle Impact Noise Detectors
vibration, shock, and acoustics testing conducted to find particulate contamination.
See Also: Particle Detectors, Particle Impact Noise Detection
-
Product
Noise Source, 1 GHz up to 40 GHz
346CK40
Noise Source
The Keysight 346CK40 is the ideal companion to Keysight´s noise figure solutions when working on high frequency applications. Since it is broadband (1 GHz to 40 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source greatly reduces measurement uncertainty, which are commonly reflections of the test signals. This is a coaxial noise source with a 2.4 mm coaxial connector. ENR typically 14 dB at 1 GHz, decreasing to 5 dB at 40 GHz (typical).
-
Product
6.5-Digit Low Noise Power Source, 32 W, 210 V, 3 A, 2-Channel
B2962B
Low Noise Power Source
The Keysight B2961B Series 6.5-digit low noise source power supplies provide a power supply and source solution that meets the difficult measurement challenges researchers, designers, and developers face working on advanced components, circuits, and materials.
-
Product
Planar-Doped Barrier Diode Detector, 0.01 to 33 GHz
8474C
Diode Detector
The Keysight 8474C is a high-performance detector using a gallium arsenide, planar-doped barrier detecting element. It features extremely flat frequency response over its entire band of operation and very good frequency response stability versus temperature. The Keysight 8474C is also very rugged with high resistance to ESD damage. The Keysight 8474C detector is available with a 3.5-mm (mates with SMA, 0.01 to 33 GHz) connector. This detector offers the options for optimal sqaure-law loads (Option 102) and for positive polarity output (option 103). Because the unit-to-unit frequency response tracking of this device is typically better than 0.3 dB, no matched response option is offered.
-
Product
SNS Series Noise Source 10 MHz to 18 GHz (ENR 6 dB)
N4000A
Noise Source
The SNS series N4000A noise source is designed for accurately measuring devices with low noise figure, with a frequency range of 10 MHz to 18 GHz and nominal ENR 6 dB.
-
Product
Noise Source Test Set, 10 MHz to 26.5 GHz
N2002A
Noise Source
The N2002A noise source test set is a low cost, stand-alone instrument that, as part of a calibration system, enables fast, repeatable calibrations with minimal levels of uncertainty.
-
Product
Magnetic Particle Flaw Detector
MT-1B
-
MT-1B magnetic particle flaw detector adapts high-capacity lithium battery pack, converse DC to AC through variable-frequency, providing magnetic powder flaw detector with magnetic power supply. With low power consumption, it can continuous work more than four hour after charging. It especially suits for working in the wild and aerial area.
-
Product
Noise Reduction Water Leak Detector
DNR-18
-
With digital noise reduction that removes intermittent sounds like barking dogs and passing vehicles. DNR-18: the advanced digital CPU eliminates intermittent interfering noises, like passing vehicles, people talking, and pedestrian footsteps.
-
Product
Particle Counter
ST-9880
-
Standard Instruments Co., LTD.
This particle counter comes with a 2.8” TFT color LCD display for a gratifying visual effect. The camera function allows capturing JPEG images and 3GP videos conveniently. This versatile particle counter is widely used. 2.8'' color TFT LCD display. With a micro SD memory card to view images and videos on your PC. Gas (HCHO, CO) detector. Air temperature and relative humidity measurement.
-
Product
Silicon Charged Particle Radiation Detectors
-
ORTEC introduced the first silicon surface barrier detectors for charged particle spectroscopy in the early 1960’s. Since then, ORTEC has expanded the product line with more than ten different options to choose from.
-
Product
Impact Hammer
WaveHitMAX
-
The invention of the first smart impact hammer provides new ways of mechanical excitation for structural dynamic applications. Smart means that the device processes its signals internally. The modal hammer WaveHitMAX guarantees fully automatic, reproducible and high-precision excitation of the test object without double hits. The user can set the number of hits, impact force and the delay between hits accounting for different degrees of damping / delay times. All presettings like zero point or impact force search are made automatically by the hammer. Manual adjustment by the user is no longer necessary.
-
Product
Particle Counter
-
TES Electrical Electronic Corp.
Monitoring air pollutant souce from dust, pertochemical industry, steel-making plant, thermal power plant, restaurant, smoke, burning plnats, driving automobiles.The meter is a real time air quality monitor instrument used to monitor the concentration of PM2.5 humidity and temperature in the indoor environment.
-
Product
Impact Testing
-
The Impact Testing software of the m+p Analyzer real time analyzer includes useful tools like the selection of a roving hammer or transducer, selection of data points/nodes, double impact detection and rejection, definition of force and exponential window and a user-definable display configuration as a visual measurement feedback.
-
Product
Pendulum Impact Testers
MPX
-
Delivering precision and safety in high-volume materials testing, the MPX pendulum impact system from Instron is optimized for Charpy and Izod testing of metals. Equipped with Bluehill Impact software, it supports capacities from 300 J to 900 J and features motorized hammer lift, automatic return, and interchangeable hammer weights. An enclosed, interlocked safety guard ensures operator protection in compliance with CE and ISO 13849 standards. The system supports key standards including ASTM E23, ISO 148, EN 10045, and others, while offering configurable reports and seamless data export capabilities.
-
Product
Airborne Particle Counters
-
Complete contamination control solution including cleanroom certification and clean area monitoring, while meeting global requirements for data integrity.
-
Product
Hammer Impact Testing
-
EDM Modal Hammer Impact Testing provides the necessary features for a single-operator experimental modal test. The Hammer Impact GUI features an intuitive step-by-step process, allowing a user to easily go through the setup and then the testing.
-
Product
Remote Particle Sensors
3718-A And 3719-A
-
Kanomax Remote Particle Sensors with analog output are designed to fit into your existing monitoring system, or they can be used as a stand-alone unit to monitor a critical area when connected to an alarm or controller. With two models available, these 2-channel remote particle sensors are capable of Modbus communication via RS485 interface. 0.1 cfm and 1.0 cfm flow rate models are available, along with flexible 4-20mA analog output with the 1.0 cfm unit (only).
-
Product
Impact Testing Machines
-
Infinity Machine International Inc.
Impact Testing Machines by Infinity Machine International Inc. - for applications such as laminated glass impact testing, plastic drop ball impact testing machine, tempered glass pendulum impact testing machine, testing machine for safety glass, slope inclined impact test apparatus for package carton, and more.
-
Product
Particle Counters
-
Testing and monitoring airborne particles in critical environments is incredibly important. That’s why Kanomax has dedicated itself to developing the best particle counting and monitoring instruments on the market. Perfect for cleanroom monitoring, mining environments, and engineering sites, our particle counters provide flexibility, and most importantly accuracy.
-
Product
Detectors
-
Our sensors are pyroelectric-based and can thus be used very easily, and at room temperature. You can choose either a standalone head with on-board electronics or go with our T-Rad meter and a separate sensor. We also have small discrete terahertz detectors in TO5/TO8 packages.
-
Product
Drop Dart Impact Tester
-
Qualitest offers a Drop Dart Impact Tester which is simple to use as a stand-alone, non-instrumented tester. It is used to measure impact resistance of film, sheet, and laminated materials.
-
Product
Particle Analysis for Liquids
-
With our partner Pamas we have developed the microscopic image analysis system PAMAS FastPatch 2 GO for automatic membrane filter analysis.
-
Product
Particle Solutions
-
Brookhaven Instruments Corporation
Particle Solutions software is used with the NanoBrook family of Particle Size and Zeta Potential Analyzers and has been updated with a new intuitive user interface and advanced features for those looking to get the most out of their measurements.
-
Product
Magnetic Particle Liquid Checker
S-2A / S-2B
-
Magnetic particle liquid checker S-2 series is a test bar which can directly check the quality of magnetic particle liquid immediately. Magnetic particle liquid checker S-2A type has a sensor at the head of straight test bar.
-
Product
Particle Impact Noise Detection
BW-LPD-DAQ4000
-
Computer based controller with predefined MIL-STD test sequences stored (New)Create unlimited custom tests with multiple vibration frequencies and acceleration and other parameters to meet unique requirements (New)
-
Product
2 Inch 535g Steel Impact Ball For Impact Test
CX-B2
-
Shenzhen Chuangxin Instruments Co., Ltd.
2 inch 535g steel impact ball for impact test
-
Product
Detectors
-
Teledyne RF & Microwave offers all types of detectors with both analog & threshold designs operating from 10MHz to 26GHz, with excellent power temperature stability.With over 50 ITAR-Free designs, many packaging options and with up to 10nS pulse response, Teledyne is able to offer the right detector for your particular application.
-
Product
Noise Generator
CNG-EbNo SNR
-
The UFX-EbNo is a fully automated precision signal to noise generator that sets, and maintains a highly accurate ratio between a user supplied carrier and internally generated noise, over a wide range of signal power levels and frequencies. The internal power meter provides repeatable SNR waveforms for accurate signal generation.
-
Product
Nano Particle Size Analyzer
SALD-7500nano
-
Delivering 10 times the sensitivity of previous models, this innovative analyzer is capable of continuously measuring changes in particle size and particle size distribution at one-second intervals, within a range spanning 7 nm to 800 μm. In addition, unique options that accommodate the measurement of even high-concentration samples (up to 20 wt%) and trace quantity samples (down to 15 μL) are available. Due to its leading-edge measurement capabilities, the analyzer will likely be used for many applications in new areas, including nanotechnology, the life sciences, and fine bubbles (microscopic bubbles).
-
Product
Detectors
-
Sanwa Electric Instrument Co., Ltd
A device or instrument designed to detect the presence of a particular object or substance and to emit a signal in response.
-
Product
Film Impact Tester
DRK136B
-
Shandong Drick Instruments Co., Ltd.
DRK136B Film Impact Tester is applicable in the precise impact resistance test of plastic films, sheets, laminated films, rubber and other nonmetal material.
