Fault Finders
Determine the location of faults.
-
Product
PXI-2510, 68-Channel, 2 A PXI Signal Insertion Switch Module
778572-10
Fault Insertion Unit
68-Channel, 2 A PXI Signal Insertion Switch Module—The PXI‑2510 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2510 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
Product
Cable Fault Locator With Time Domain (Intelligent Bridge)
GT00ZD00ZY
-
GAOTek Cable Fault Locator with Time Domain has a reflectometer to locate faults in metallic cables and Intelligent bridge for tesing the broken line
-
Product
PXI Dual Bus 74-Chan 2A Fault Insertion Switch
40-190B-002
-
The Dual Bus, 74 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Board Fault Locator
SYSTEM 8 (BFL)
-
The SYSTEM 8 Board Fault Locator provides the user with the ability to functionally test all common digital ICs in and out-of-circuit. A combination of industry recognised test techniques provides a high level of fault coverage. Additional tools are provided by the SYSTEM 8 Premier software to further enhance the unit\'s wide range of applications.
-
Product
Fault Detection Device in PV String
-
Hanwa Electronic Ind. Co.,Ltd.
◆Very light and easy to carry.◆Possible to find fault areas that can’t find by Voc.◆Measurement Voc and Vc.◆Possible to check data and record the data using Android.
-
Product
PXI-8511, 1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module
780686-02
CAN Interface
1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module—The PXI‑8511 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The PXI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
Platinum Tools Fiber Optic Visual Fault Locator
#TVFL100
-
Fiber optic visual fault locator works with virtually all 1.25mm and 25mm fiber optic sizes and connector types.
-
Product
Vector Network Analyzer 9KHz-3.2GHz. Includes Adv Meas Kit, Distance To Fault Opt, Cal and Utl Kits
T3VNA3200
Vector Network Analyzer
Vector Network Analyzer 9KHz-3.2GHz. Includes Adv Meas Kit, Distance To Fault Opt, Cal and Utl Kits.
-
Product
Real-Time Online Monitoring to Detect and Analyze Potential Partial Discharge (PD) Signals and Insulation Faults using UHF, AE, and HFCT
PDMonitor
-
Power Monitoring and Diagnostic Technology Ltd.
The PDMonitor, which utilizes Ultra High Frequency (UHF), Acoustic Emission (AE) and High Frequency Current Transformer (HFCT) sensors and is designed to conduct real time online monitoring to detect and analyze potential Partial Discharge (PD) signals and insulation faults before they lead to breakdown or catastrophic failure in power assets. The system provides the developing trend of the PD, when occurring, as alarms in real time, thus helping to predict the insulation degradation status of the asset, prevent sudden accidents, and provide an effective database for Condition-Based Maintenance (CBM) of power assets.
-
Product
Cable Fault Locator
-
We are one of the leading manufacturers, exporters of suppliers of a premium quality range of Cable Fault Locator that is extensively used to trace and locate the fault of underground cables. This fault locator is manufactured at our hi-tech manufacturing unit as per international quality standards under the supervision of our professionals using superior quality components. Offered fault locator is made available in different specifications to meet the diverse requirements of the clients. Our honorable clients can avail this Cable Fault Locator from us at industry-leading prices.
-
Product
Accessories: Intermittent Fault Emulator
-
The Intermittent Fault Emulator (IFE) is the solution. The IFE enables manufacturers, suppliers and operators of any Intermittent Fault Detection (IFD) tester to demonstrate and verify its capabilities to detect and isolate intermittent faults.
-
Product
Fault Diagnostics in Power-Off State
QT55
-
Qmax Test Technologies Pvt. Ltd.
Signature Method of Testing is also known as VI Trace Characteristics, is a proven fault diagnostics technique in Power-Off state while testing a board. By applying known wave from signal with desired Voltage, Source impedance and Frequency of the stimulus signals, depending upon the test node and its characteristics, a Voltage (V) vs Current (I) graph is plotted and studied.
-
Product
PXI Fault Insertion Switch, 7-Channel, One Fault Bus, 20 A
40-193A-001
Switch Module
The 40-193A-001 is a 7-Channel Fault Insertion switch with one fault bus, designed for the simulation of fault conditions in automotive systems. The module is capable of switching current up to 20A.
-
Product
Fault Passage Indicator for Lines
LineTroll R400D
-
LineTroll R400D Fault Indicator indicates earth- and short-circuit faults and can distinguish between permanent and transient faults. The indicator has two sensors and use both the electrical field and the magnetical field to detect faults on all three phases.
