Tachometer Testers
See Also: Tachometers, Engine Tachometers
-
product
Desktop Material Testers
Desktop force/displacement testers record both force and displacement. Programming is facilitated by the unique program dial using plain language menu screens.The jog movement moves the sensor .05mm for each click of the program dial (under no load).
-
product
Battery Load Tester
MD4260
Test capabilities: Battery voltage, battery cranking, battery charging volts and good/bad battery test. Test batteries on and off the car in just 30 seconds. Heavy duty copper-plated clamps. Internal loaded unit with a 100-amp load capacity. Load safety switch to prevent arcing. For 6- and 12-volt batteries.
-
product
Spray Rating Tester
TF160
TESTEX Testing Equipment Systems Ltd.
Spray Rating Tester, to determine the surface wetting resistance of fabrics, which may or may not have been given a water-resistant or water-repellent finish.
-
product
AMIDA 5000 Tester
AMIDA 5000 is a high-end performance test system, combining analog, mixed-signal and logic with the latest test solutions. High pin count - as many as 512 smart multi-function pinframes and 128 sites. Ability to provide cost-optimized test solutions for a variety of consumer components in power management and mobile device components. This system has a higher number of parallel tests and a higher level of capability. This series of test systems provides a powerful test combination with high-speed hardware and software integration. The 5000 series test system is the best analog, mixed signal, digital IC, PA test system for engineering verification and mass production. It can be easily connected to all well-known wafer probing machines and sorters, and also supports parallel test functions. The 5000 series meets customers' needs for high-precision, high-resolution, high-reliability, user-friendly, and low-cost testing and measurement of test systems.
-
product
Breaking Force Testers
Break Force Tester is applied for break force test of the ampoule, lipstick, lip cream and other materials.
-
product
Spin Testers and Bearing Assemblies
Vidac has created several spin test systems ranging from the basic manually operated model shown here to fully automated machines that can spin the customers components to a specific speed profile. Our 3D design capability ensures the tight tolerance fit required for high speed rotation.
-
product
Power Supply Tester
UTS-625
The UTS-625 provides the ultimate in ATE flexibility. Its open-ended architecture allows users to custom configure the Autotest system to meet the needs for one or multiple applications. Housed in standard full size racks, the UTS-625 system may be expanded from a single bay to multiple bays as required.
-
product
2Mbit/E1 Error Rate Tester
CA6037
CA6037 is a hand-held equipment designed for 2M bit erroe rate test, applicable to telecommunication access networks, transmission networks and the start-up, check and maintenance of optical communications systems.
-
product
Insulating Oil Dielectric Loss Tester
HDLT
Hention Electrical Equipment Co., Ltd.
This integrated precious insulation oil dielectric loss tester is for measuring dielectric loss TAN and capacitance of transformer insulation oil.This is a high precision instrument; integrated with oil cup, temperature control instrument, temperature sensor, dielectric loss test bridge, AC test power, and standard capacitor, etc.
-
product
Silicon O/C Content Tester
OCT-2000
Manual, non-contact measurement of wafer thickness, TTV and bow. Portable and easy to set-up, the Proforma 300/G measures all wafer materials including Silicon, Gallium-Arsenide, Indium-Phosphide and wafers mounted to sapphire or tape.
-
product
Basic Fuel Injection Pressure Tester
FIT448
This set includes everything to test the following: Bosch AFC, MPC, Digijet/Digifant- (except CIS- use our FIT447) Chrysler Corporation Ford Motor Company General Motors (except TBI- use our FIT446) Japanese Fuel Injection Systems Others using Bendi. The 2-1/2" gauge has a dual scale dial with ranges from 0-100psi and 0-7 bar.
-
product
HDMI Tester
21-8575-00
The HDMI Tester is designed to provide fast convenient verification of proper pin connections of HDMI cables and wall plates. The set includes a Main Test Unit and Remote Test Receiver.
-
product
Enterprise Firewall Performance Tester
Xena Safire
Enterprise Firewall Performance Tester NextGen Enterprise firewalls provide network security by segmenting corporate LANs. Unfortunaltey advanced security functions (e.g. antivirus, app-control, IPS and SSL decryption) can have a performance penalty. Using these features can quickly impair network performance by as much as 90% negatively impacting users and business performance.
-
product
ECU Tester
State-of-the-art analog and digital technology are covered in the ECU, measurement and control systems and flexible high performance is required for the evaluation. Verification of reliability is very important because it is an important component further life-threatening people. From previous experience, tester of the ECU has come to our proposed notice that it is better to use a TestStand and PXI is the optimal solution of Peritec ECU tester.
-
product
Magnetfield Testers
The magnetic field tester is suitable for rapid and precise testing of electro-magnetic switches and valves. Their tip lights up to indicate the presence of permanent, DC or AC magnetic fields. Thereby, they are so sensitive that very often it is not necessary to remove covers or cladding from machines and the function check can be carried out without any setting-up time or stopping the machine.
-
product
Lever Handle Bed of Nails Testers
Automator Manual Family
Designed to provide factory assembly line conveyor based pneumatically actuated full test automation. Interchangeable pneumatics and manual lever options provide operation as a fully automated tester or as a manual bench top tester. These functional interchangeable options allow this fixture to grow with you as your production volumes increase. Test plate changeover is a quick 2 minute job. 4 thumbscrews to change the bottom plate and 4 SHC screws to change the top plate. The top plate drops down and slides out with the connector assembly. The bottom plate lifts up and out. The new plates slide back in. All rear panel connectors are mounted to the aluminum bracket on the top plate. This whole top plate assembly slides out together eliminating wiring hassles. Double sided access plate sets use transfer pins to get the signals from the bottom plate up to the top plate.
-
product
TLP Tester
Tokyo Electronics Trading Co., Ltd.
A method for semiconductor characterization of Electrostatic Discharge (ESD) protection structures.
-
product
Suspension/Road Contact Tester
VLT3673-G6
The VLT 3673-G6 suspension / road contact testers operate according to the well-known EUSAMA principle. However, the diagnostic options are not restricted to the contents of this specification. In addition to the usual road contact values, the following values are also measured and displayed: the contact value difference, resonance frequency and wheel weight at minimum contact value, tyre rigidity, wheel weight and axle weight. There is a general final evaluation so that all these values do not have to be interpreted after every test.
-
product
High Voltage Surge Testers
HVST
The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. This voltage is displayed on an oscilloscope and recorded on the Pass/ Fail LED latch monitor. This voltage will be accurate despite the impedance of the winding being tested. The insulation system can be tested way above the operating voltage because of the brief duration of the applied voltage test pulse. This allows faults to be detected long before they become apparent at operating conditions.
-
product
Low Temperature Retraction Tester
EKT-100TRB
EKT-100TRB-Low Temperature Retraction Tester is designed in accordance with ASTM D1329, ISO 2921 with fully automatic and computerized controlling system.
-
product
Flash Point Testers
Flash point is the lowest liquid temperature at which a test flame causes sample vapors to ignite. Fire point is the temperature at which the test flame causes the sample to ignite and remain burning for ≥5 seconds.
-
product
Electrical Safety Tester
MACROEVTEST
Multifunction instrument for electrical installation safety testing, power quality analysis and EVSE safety testing
-
product
Disk Peel Tester
DRK186
Shandong Drick Instruments Co., Ltd.
DRK186 Disk peel tester is applied to test the ink layer bonding strength of plastic film printing and PT print. To test the surface adhesion state of vacuum coating, surface coating, composite process.
-
product
Diode Tester
FEC VF40CM
Frothingham Electronics Corporation
The VF40CM is intended for testing VF, HALF CYCLE SURGE, and THERMAL RESPONSE/RESISTANCE on small- and medium-power diodes and rectifiers. It can also measure THERMAL RESPONSE/RESISTANCE on NPN and PNP bipolar transistors using an external user-supplied VCB supply.The VF40CM also is sometimes used to measure VZ of low-voltage zener diodes up to the compliance voltage limit of the tester. 20V at 20A is possible.
-
product
Battery Discharge and Charge Tester
HD Power Test Equipment Co.ltd
Battery Discharge Charge Tester is mainly used for the charge test of the lead-acid battery of the backup power supply in the telecommunications, mobile, substation, railway transportation and pertrochemical industry power DC industries. It can proceed the discharge and charge for the batteries to extend the lift-time.
-
product
Voyager Intermittent Fault Detection Tester
This family of testers is available as the portable VIFD™ tester (previously called the Ncompass-Voyager) with 128, 256 or 512 test points, and it is available as a 19” rack-mount system – the IFD & Isolation System (IFDIS™) – with thousands of test points. Testers are available from Copernicus Technology for purchase or lease. Alternatively we can provide the full test service for you and we also provide all the corresponding test accessories listed under the Test Equipment menu button.
-
product
LD/LED ESD Tester
Hanwa Electronic Ind. Co.,Ltd.
Performs automatic destructive evaluation of Lazer-Power.
-
-
product
Coatings On Concrete Adhesion Tester
106/6
The Elcometer 106/6 Adhesion Tester has been specifically designed to measure adhesion strength of coatings on concrete.
-
product
Igniter Testers
Igniter Tester is a failsafe and portable digital ohmmeter specifically designed for ultra-safe resistance testing on squibs, flares, bridge-wire, and other explosive devices. The 620A-4 ohmmeter has been approved by the USAF Non-Nuclear Munitions Safety Board for usage on all non-nuclear munitions, and independently certified to meet Mil. Std. 810 Mtd. 511 for usage in fuel-filled environments. Due to its intense self-safety design and numerous certifications, the 620A-4 failsafe ohmmeter is the industry standard for military programs in need of igniter testing.
