Environmental Testing Services
Environmental Testing Services is a general topic for companies that can support testing products in their intended operating environments, to ensure that they will perform as expected.
See Also: Environmental Test, Environmental Chambers, Environmental Test Services
-
Product
Transformer Test Equipment
-
KV Hipot Power Test Equipment Co.,Ltd
Transformer Test Equipment. Ensure that a transformer meets performance and reliability requirements, from the production line to after a repair or upgrade, when a major disruptive event occurs such as a lightning strike, or for preventive/predictive maintenance.
-
Product
DDoS Testing
-
DDoS testing missions enable enterprises, operators and governments to test their resilience against DDoS and evaluate their DDoS mitigation infrastructure.
-
Product
C++ Test Framwork
Google Test
-
a unit testing library for the C++ programming language, based on the xUnit architecture. It can be compiled for a variety of POSIX and Windows platforms, allowing unit-testing of C sources as well as C++ with minimal source modification.
-
Product
Primary Test Equipment
LET-1000-RD
-
It allows to perform with sufficient power, all the primary current injections to test the proper function and wiring of all the elements that compose the protection and measuring section in a substation.The regulation system is based on a continuously variable autotransformer (Variac) that supplies to a power transformer that delivers the high current outputs and isolate the main supply from the load. A built-in ammeter and a timer gives the information about the current value and the operation time of the relay or breaker under test.
-
Product
Multifunctional Safety Tests
-
Manufacturers of electrical or electronic products are required by law to carry out an electrical safety test before placing them on the market. This final test takes place at the end of the manufacturing process and is therefore also referred to as an EOL test (end-of-line). Depending on the prescribed standard and directive, the following parameters are tested:- Leakage current and discharge current- Insulation resistance or the insulation strenth- Dielectric strength or electric strength- Correct installation of the protective conductor (ground continuity and ground bond test)- Faultless functioning of the product under the conditions defined for intended use (function or run test
-
Product
Switchgear Testing Solutions
-
IES Systems is a world leader in the design and manufacturing of power switchgear test systems.*GFCI/AFCI Circuit Breaker Test Solutions*Medium Voltage Breaker Test Solutions*Residential Circuit Breaker Test Solutions*Molded Case Circuit Breaker Test Solutions*AIR Circuit Breaker Test Solutions*Vacuum Bottle Test Solutions
-
Product
Safety & Survival Testing
-
Their life is in your hands. That’s why you need Dayton T. Brown, Inc. to carry out thorough safety and survival equipment testing with performance and reliability evaluation of your critical safety product.
-
Product
Primary Test Manager
-
The Primary Test Manager™ (PTM) software supports you during diagnostic testing, condition assessment and data management of medium- and high-voltage assets, such as circuit breakers, rotating machines, grounding systems, instrument and power transformers as well as bushings and on-load tap changers (OLTC).
-
Product
Material Testing Machine
-
Beijing TIME High Technology Ltd.
A device used to measure the physical and mechanical properties of materials.
-
Product
PCB Test Connectors
Tag-Connect
-
Tag-Connect is a simple and secure way of connecting debuggers, programmers and test equipment to your PCBs. Tag-Connect uses a specially designed and patented connector for making the connection to your PCB (Patent Pending for the -NL versions). Tag-Connect eliminates the need for a programming or JTAG connector on your PCB.
-
Product
PIM Testing
-
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Passive Intermodulation (PIM) is a non-linear response of two or more signals of different frequencies mixing together in a passive device, e.g., antenna, cable, con- nector or splitter. Today, PIM has become a very serious, and challenging issue for mobile operators, equipment vendors, and component manufacturers due to frequency planning in modern communication networks, the usage of high-power transmitters and the usage of more sensitive receivers in base stations. If a PIM with sufficient magnitude generated from a transmitter falls within an adjacent receiver channel, it causes serious interfe- rences to the base station receiver and will significantly degrade the network quality of service.
-
Product
Photo Detector Testing
-
With the rise of 5G technology and popularization mobile devices, more and more advanced photoelectric sensors are used in our daily lives. In order to be better applied to mobile devices, the photosensitive area of these advanced photodetector is getting smaller and smaller. However, these applications place higher and higher requirements on the light sensing performance of advanced photodetectors. In the process of shrinking the photosensitive area, it also brings the challenge of accurate measurement of quantum efficiency. Enlitech adopts the spatial light homogenizing technology and follows the ASTM standard “Irradiance Mode” test method, which is proven that it can accurately perform quantum efficiency and other key parameter measurements of advanced photodetectors.
-
Product
EMC Testing EMCD
-
Efficient and flexible EMC testing services for product CE marking, UKCA marking and demonstrating compliance with US FCC and Canadian ISED regulations. Our experienced engineers will guide you through the test process, helping you to save time, minimise project costs and get your product to market quickly.
-
Product
VLF test system
BAUR PHG 80 portable
-
Portable, high performance test generator with VLF truesinus technology. The BAUR PHG 70/80 portable VLF test systems are used for cable and cable sheath testing of medium-voltage cables of up to 50 kV and electrical equipment.* 3 voltage shapes in one device: VLF truesinus, VLF square wave and DC voltage* For medium-voltage cables of up to 50 kV operating voltage* Cable testing, fault conditioning, cable sheath testing
-
Product
Test Solution Offering BER Testing
Eye-BERT Micro LR
-
The Eye-BERT Micro LR is a low cost, easy to use test solution offering BER testing at any rate between 6.312 and 125Mbps on either optical or electrical interfaces. Features include: continuously variable bit rate, user programmable pulse generator, internal CDR with retimer mode, bit rate measurement, and recovered clock output. The Unit is supplied with anti-skid bumpers for bench use, and is small enough to be integrated into larger systems for dedicated link verification.
-
Product
Reverse Engineering Services
-
The term “reverse engineering” can be a little confusing. It is sometimes used for things like software and electronic circuits. When 3D scanning companies use the term, they are referring to the process of re-creating design drawings by taking measurements and/or scans of the part itself. It is a 2-step process: 1) capture a 3D scan of the object, and 2) Create a 3D CAD model of the object
-
Product
Custom Test Solutions
-
Genuen has extensive expertise in the design, development, and deployment of custom test systems. All of our core expertise areas were at one time developed as unique custom test systems. Our broad-based knowledge of testing principles and tools allow us to deploy solutions for even the most challenging applications.
-
Product
Manual Test Adapters
-
Manual test adapters (MA) from INGUN are available in several series and series, which differ in terms of use, maximum permitted contact force, parallel stroke, size and service life.
-
Product
Impulse Test Equipment
-
mpulse test equipment for testing of low-voltage rotator windings.The equipment is composed of a surge impulse generator circuit, phase selector unit (selection between U, V and W), and waveform recorder circuit to provide a differential method type of impulse testing instrument.
-
Product
Ball Pressure Test
-
Premier Electrosystems' Ball Pressure Test is used to determine dimensional stability under stress at elevated temperatures. It analyses the relationship between the degree of deformation and the temperature when the test specimen is subjected to a constant load.
-
Product
Power Networks Test
TX6000
-
The TX6000 is a hand held Time Domain Reflectometer with 11 range scales covering the range 0-6000 meters, with a 7 mater first range scale and a 0.5 meter dead zone near and far end faults are clearly displayed on its 128×64 pixel back light Liquid Crystal Display.
-
Product
Website Penetration Testing
-
The vulnerabilities in a website need to be proactively fixed before the weaknesses are exploited by hackers, which in turn may lead to loss in customer’s confidence. We at Precise Testing Solution provide extensive planning to conduct website penetration. We check for holes in CRM, extranets, and internal network applications.
-
Product
Transformer Testing Equipment
-
Offering you a complete choice of products which include Automatic Transformer Turns Ratio Instruments (ATRI- 3), Automatic Transformer Turns Ratio Instrument (ATRI-201), VTRI-2000 ( Transformer turns ratio instrument ), Current Transformer Test Set (CTC-1), Potential Transformer Tester ( PT Tester ) and Current Transformer Tester ( CT Tester ).
-
Product
Semiconductor Test Equipment
IC Tester
-
Equipment to determine the pass/fail of devices in the wafer inspection process and the final inspection process after packaging.
-
Product
Laser Power Meter Calibration Services
-
Following the successful setup of our UKAS accredited laser testing laboratory we have now set up a calibration laboratory in our Bournemouth premises for the purpose of offering laser power meter calibrations. We are able to undertake NPL traceable calibration of laser power meters at any of the following wavelengths:
-
Product
Test System
Tessy
-
TESSY automates the whole unit test cycle including regression testing for your embedded software in C/C++ on different target systems. As an easy-to-install and easy to operate testing tool TESSY guides you through the unit test workflow from the project setup through the test design and execution to the result analysis and reporting. TESSY takes additionally care of the complete test organization as well as the test management, including requirements, coverage measurement, and traceability.
-
Product
Test Contactor/Probe Head
Mercury
-
Mercury™ test probes and contactors are excellent spring probes for the laboratory though they were designed with the robust qualities needed for high-volume production test. Their unique design ensures excellent plating quality for low, consistent resistance, long life, and high-test yields.Mercury probes are available with minimum pitches of 0.3 mm, 0.4 mm, 0.5 mm, and 0.8 mm, to provide the best performance at any device pitch. Mercury probes have bandwidths of up to 22 GHz, and can carry over 3 Amps of current. The Mercury is an excellent choice for any test application.
-
Product
Container & Package Testing
-
*Incline Impact. *Drop. *Cobb. *Static and Dynamic Compression. *Dart Puncture. *Environmental Conditioning. *Vertical Linear, Rotary Motion, Sinusoidal and Random Vibration. *Internal Pressure. *Vacuum
-
Product
Semiconductor Test
-
Smiths Interconnect’s test socket and probe card solutions utilize IDI contact technology to ensure superior quality and reliability in semiconductor test applications. Our best-in-class engineering, development and technical expertise ensure support of automated, system level and development test platforms.
-
Product
Environmental Sensors
-
Various Environmental Sensors including Room, Ceiling, Radiation and Contacting Temperature Sensor
