Showing results: 61 - 75 of 282 items found.
-
MI series -
Ono Sokki
There are MI-1271, 1/2-inch back electrets-type microphone which has improved the environmental stability against temperature and humidity, MI-1235 which emphasizes on a wide frequency range and MI-1433 which realizes a similar environmental resistance at a low price. MI series microphone is used in combination with the preamplifier and the microphone. Since microphone and preamplifier are not built-in type, installation costs can be reduced in the event of a fault.
-
-
M23R -
Earthworks, Inc.
The M23R is a precision engineered 23kHz omnidirectional measurement microphone ideally suited for acoustical measurements including loudspeaker design and quality control, sound system setup and troubleshooting, room acoustics, or any application where an accurate free-field measurement microphone is required.
-
HSU III -
HEAD acoustics GmbH
The HEAD-Shoulder-Unit HSU III is an artificial head microphone for binaural recordings.
-
IMM-6 -
Dayton Audio
The Dayton Audio IMM-6 is a professional-quality measurement and recording microphone that is designed to work with the entire suite of Apple “iDevices” – iPad, iPhone, and iPod. The rugged construction and compact size make it the perfect companion for audio professionals who must work on-location performing acoustic analysis, monitoring audio levels, or recording. Each IMM-6 is individually hand-calibrated using a laboratory-standard measurement microphone, for consistent, repeatable measurements that match the level of precision previously offered only by expensive stand-alone microphones.
-
378A04 -
PCB Piezotronics, Inc.
The 378A04 is a matched system that is comprised of a high sensitivity microphone and a low noise preamplifier that contains a built-in filter that enables the free-field response to remain flat over a wide frequency range. The system requires a minimum of 4 mA and measures to 6.5 dBA (5.5 dBA typical) within a cost efficient, prepolarized (0V) design. PCB's model 378A04, the industry's first prepolarized low noise microphone and preamplifier system allows you to measure extremely low amplitudes. In the past this was only possible with externally polarized solutions. With a typical noise floor of 5.5dBA, this microphone system delivers all of the benefits commonly associated with prepolarized systems.
-
cm-125 -
AudioControl Industrial
The CM-125 consists of the MA-20 mic carrying bag, mounting clip, and windscreen plus the CM-25 individually calibrated everyday measurement microphone. The CM-25 is the CM-20 " back electret, omni-directional microphone individually calibrated with a provided file in FRD format with one-third octave measurement points from 5 Hz to 25 kHz. The file comes on a serialized USB memory stick for convenience.
-
itestmic -
AudioControl Industrial
iTestMic is the professional-grade test and measurement microphone that works with iPhone 4, iPod touch 4, and iPad. The Lightning version can also be used with newer iOS devices.
-
TM1 - TM1 PLUS -
Audix Microphones
The TM1 is a 6 mm pre-polarized condenser microphone used for test and measurement applications. The TM1 is known for its linearity, accurate response, consistency, ease of use and affordability.
-
SparkFun Electronics
This small breakout board couples an Electret microphone (100Hz--10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a microcontroller’s analog-to-digital converter. Each breakout comes fully assembled and works from 2.7V up to 5.5V.
-
130A23 -
PCB Piezotronics, Inc.
Nominal Microphone Diameter: 1/4" Frequency Response Characteristic (at 0 incidence)Free-FieldInherent Noise (A Weighted)<30 dB(A) re 20 Pa<30 dB(A) re 20 Pa Dynamic Range (High)150Environmental Temperature Range ( Temperature Effect on Output (-10 to +50 C)<0.7 dB<0.7 dB[2] Influence of Axial Vibration Excitation Voltage 18 to 30 VDC18 to 30 VDC
-
cm-120 -
AudioControl Industrial
The mic bag is a little wonder. On one side are two pockets for microphones and on the other are pockets for mic stand clips, windscreens and other necessities. The bag is fully padded to protect its contents and includes both a long zipper for completely opening the bag as well as a convenient carrying handle. The CM-120 ships with an universal mic clip and cool blue foam windscreen in its interior pockets. This is a quality package at a great price.
-
Analog Devices Inc.
Analog Devices mic pre-amp audio interfaces provide a high fidelity, high performance solution for audio products. Specifications for this family include ultralow 1.5 dB noise figures, 140 dB gain range, and high gain capability. Operating in an extended industrial temperature range of –40°C to +85°C, this portfolio of mic pre-amp audio interfaces supports many applications, including precision instrumentation, active filters, low noise amplifier front ends, surveillance systems, computerized voice recognition, and a variety of other industrial and consumer products. As the first choice for serious audio engineers, Analog Devices mic pre-amp audio interfaces can give your applications the performance needed to meet the most demanding specifications.
-
MI-1531/MI-3140 -
Ono Sokki
The 1/4-inch diameter condenser microphone MI-1531 with its preamplifier MI-3140 enable to measure the high frequency band more than 20kHz which it is impossible by using the 1/2-inch microphone. Amplifier is not required in use as it is a back electret-type condenser microphone, which differs from a bias-type microphone. And also, the MI-1531 achieves a measurement at Max. 168 dB as a performance of a microphone itself.
-
ICS-40180 -
SparkFun Electronics
The SparkFun Analog MEMS Microphone Breakout makes it easy to work with the InvenSense ICS-40180 analog microphone. This board features an OpAmp to bring the output of the microphone to a usable level, allowing you to plug directly into an ADC on a microcontroller or something like the SparkFun Spectrum Shield.