Parasitic Voltage
draw on battery when vehicle is off.
-
Product
sbRIO-9221, Non-Enclosed, ±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
781116-01
Voltage Input Module
Non-Enclosed, ±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The sbRIO‑9221 performs single-ended analog input. The wider voltage range makes this module well suited for industrial-level, automotive, or even smaller-cell battery measurements. There are two connector options for the sbRIO‑9221: a 36‑position spring‑terminal connector and a 37‑position DSUB connector. Non-enclosed modules are designed for OEM applications.
-
Product
DC-Powered, AC Voltage Monitor
VAD/VQD
Voltage Monitor
NAI’s VAD and VQD are DC-Powered, AC Voltage Monitors used to monitor voltage characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within pre-determined limits. These voltage monitors are ideally suited for rugged defense and industrial applications.
-
Product
NI-9239, ±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
779593-01
Voltage Input Module
±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9239 performs differential analog input. With channel‑to‑channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. In addition to safety, isolation eliminates measurement errors caused by ground loops because the front end of the module is floating. Designed for both speed and accuracy, the NI‑9239 is an effective general-purpose analog module because of its resolution, sample rate, and input range.
-
Product
NI-9215, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
783739-01
Voltage Input Module
±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9215 performs differential analog input. The module contains NIST-traceable calibration, a channel‑to‑earth ground double isolation barrier for safety and noise immunity, and high common-mode voltage range. It is also offered in two connectivity variants: 10‑position screw terminal or BNC.
-
-
-
Product
Voltage Tester
HH2611
-
Handy, quick response and easy to use tool. Safe to use Non-Contact testing 90-220V AC voltage. Delect AC voltage without connecting into the wire circuit. Very bright LED and buzz sound alarm if voltage is present. Used to detect where the wire is broken. Used to detect whether an outlet is present of voltage. Used to detect a broken Christmas bulb out of a series of connected Christmas bulbs
-
Product
Voltage Detectors
-
Available with a digital readout or a simplified LED display Seaward's specialist range of voltage detectors have the versatility and durability to cope with all types of user demands.
-
Product
sbRIO-9201, Non-Enclosed, ±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
781114-01
Voltage Input Module
Non-Enclosed, ±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The sbRIO‑9201 is an effective combination of channel count and speed at a low price for an economical multifunction system. In addition to the absolute protection from the isolation, the module features up to 100 V of overvoltage protection for errant signal connection or unexpected outputs to the individual channels. Non-enclosed modules are designed for OEM applications.
-
Product
Voltage Detector
LV-1
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Using conductive rubber tip, free from short circuit. With slip stopper for the safety use.
-
-
Product
AC-Powered, AC Voltage Monitor, Adjustable
VMA
Voltage Monitor
NAI’s VMA is a field-adjustable, AC-Powered, AC Voltage Monitor used to monitor voltage characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within pre-determined limits.High and low voltage limits, and "pick-up" and "drop-out" time delay are field-adjustable. The VMA voltage monitor is ideally suited for rugged defense and industrial applications.
-
Product
Voltage Meter
MDN8I
-
MDN8I is a mezzanine module designed for high-precision measurements in dynamic signal analysis systems, as well as for joint work with ICP sensors and vibration transducers with a charge output (force sensors, dynamic pressure, acoustic emission, vibration displacement, etc.). The MDN8I mezzanine module has electrical characteristics no worse than those of most foreign and domestic counterparts, and in some parameters exceeds them.
-
Product
Voltage Testing
VisualDetect series
-
Hachmann Innovative Elektronik
With the VisualDetect line you get a type series of handy, exact and easily operated voltage detectors and maintenance testers.
-
Product
Voltage test
-
Yuyao City Yinte Neon-Electroscope Factory
voltage tester or detector is an electrical tester that helps to detect the presence of voltage. Voltage presence is useful information to have when troubleshooting or working on a failed asset. The first tool you'll reach for is a non-contact voltage detector.
-
Product
Voltage Amplifiers
-
Switchable gain up to 100 dB (x 100,000)Bandwidth DC to 100 kHzDC-drift 0.6 µV/°CInput noise down to 0.4 nV/√HzSwitchable AC/DC-couplingLocal and remote controlInput impedance up to 1 TΩ
-
Product
Voltage Meter
МН32С
-
The mezzanine module (mezzanine) МН32С is designed to measure instantaneous voltage values over thirty-two differential channels.
-
Product
Voltage Meter
MN8I
-
The МН8И mezzanine module (mezzanine) is designed to measure instantaneous voltage values over eight differential channels isolated from each other.
-
Product
Voltage Sag Generator
SKS-1120GTA
-
Shanghai Sanki Electronic Industries Co., Ltd.
The cycle drop simulator is used to reproduce the voltage fluctuation phenomenon of commercial power supplies. Simulate the grid voltage drop and short-term interruption caused by the accident or the sudden change of the large load in the low-voltage power grid, or the grid voltage change caused by the continuous change of the load. Used to evaluate the performance of the equipment under these voltage changes.
-
Product
Test Voltage Indicators
PRV240FS
-
Verify your test tool works without unnecessary exposure to shock and arc flash. Make the process easy by using the PRV240FS Proving unit. Verifying that your T6 electrical tester is working properly reduces the need for personal protective equipment (PPE) when a known voltage source is not available for verification before tests are performed.
-
Product
High Voltage Testers
GLP2
-
GLP2-tester series are the result of our experience in manufacturing following “customer based technology“ for more than 20 years. With precise, intelligent test processes the testers set the standard regarding operating ease, modularity, functionality, measurement accuracy and performance.AC tests up to 100 kV. DC tests up to 98 kV. Suitable for production testing of luminaries, white goods, coils etc.
-
Product
Non-Contact Voltage Tester
1AC II
-
The portable 1AC II non-contact voltage tester from Fluke are easy to use – just touch the tip to a terminal strip, outlet, or supply cord. When the tip glows red and the unit beeps, you know there's voltage present. Electricians, maintenance, service, safety personnel, and homeowners can quickly test for energized circuits in the workplace or at home and even detect miswires of an electrical outlet.
-
Product
HIGH VOLTAGE MEGOHMMETER
MI-10KVe
-
The MI-10KVe High-Voltage Megohmmeter is a truly portable device that allows the measurement of insulation resistances using test voltages up to 10 kV. It employs a state-of-the-art technology for the safe measurements of insulation resistances up to 2.000.000 MΩ with four test voltages: 1 kV - 2 kV - 5 kV and 10 kV.
-
Product
NI-9202, ±10 V, 10 kS/s, 24-Bit, 16-Channel C Series Voltage Input Module
784399-01
Voltage Input Module
±10 V, 10 kS/s, 24-Bit, 16-Channel C Series Voltage Input Module - The NI-9202 has excellent flexibility to meet the needs of your applications. The module has 16 simultaneous sampling, differential input channels to create large, distributed systems in a rugged form factor. It also has configurable filters to eliminate noise in your system while maintaining low-latency to be used in control systems.
-
Product
Voltage Tester Pen
-
Shenzhen UYIGAO Electronic Technology Co., Ltd
A non-contact voltage tester is the safest way to make sure the power is off without touching any wires. Before you open an electrical box, you should: - cut off power to the outlet at the main electrical panel - confirm you turned off the right circuit This is where the non-contact voltage tester comes in handy.
-
Product
Non-Contact Voltage Tester
NCVT-1
-
Non-contact detection of voltage in cables, cords, circuit breakers, lighting fixtures, switches, outlets, and wires.High intensity, bright green LED indicates the tester is operational and aids in illuminating the workspace.When voltage is detected, a high intensity, bright red LED illuminates and a warning tone sounds.Discrete digitally controlled ON/OFF power button.Auto power-off feature conserves and extends battery life.Microprocessor controlled low-battery indicator and tester shutdown.CAT IV 1000 Volt safety rating provides expanded operation and protection.
-
-
Product
Voltage Testers
-
The non-contact voltage tester detects live conductors on cable connections, cable drums, sockets, switches, junction boxes etc. Due to capacitive measurement procedures, no current flow is required and interruptions can be indicated quickly and accurately.
-
-
Product
Voltage Dividers
-
Measurements International Ltd.
A series of resistors or capacitors which can be tapped at any intermediate point to produce a specific fraction of the voltage applied between its ends.
