Current and Potential Transformers
current and potential transformer T&M instruments.
-
Product
AC Current Isolated Sensor Two / Four Wire Transducer
TSCT (Average Sensing) / TFCT (TRUE RMS)
-
Kusam Electrical Industries Limited
• Transform Input: AC 5~400A directly into DC 4~20mA, no need external CT.• Suitable for application with high waveform distortion :(Frequency converter, Motor, SCR )• High accuracy ＜0.5%• High response time• High stability, easy connection.
-
Product
AC Current Probe 2 mV/A, 3,000A, 0.11 Hz LF Bandwidth, 6.5MHz HF Bandwidth, 4m cable, 300mm coil
T3RC3000-LF
-
AC Current Probe 2 mV/A, 3,000A, 0.11 Hz LF Bandwidth, 6.5MHz HF Bandwidth, 4m cable, 300mm coil.
-
Product
Transformer Loss Measuring Bridge
MLS 7100
-
The MLS 7100 transformer loss measuring bridge was especially designed to greatly simplify the determination of transformer core and copper losses – an ideal choice when working on site. The measuring bridge features open circuit as well as short circuit measuring. Many transformers can be directly connected to the MLS 7100 without needing further transducers.
-
Product
Split Core Hall Effect DC Current Sensor
CYHCT-C2TV
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a split core and a high galvanic isolation between primary conductor and secondary circuit. It can be used for measurement of DCcurrent etc. The output of the transducer reflects the real wave of the current carrying conductor.
-
Product
Current Probe Calibrator
KSZ
-
PMK Mess- und Kommunikationstechnik GmbH
Since Current Probes are often exposed to hard working conditions, a performance check is recommendedbefore every use. These Current Probe Calibrators generate square wave pulses from 0.05 A to 1000 A with an accuracy better 1%. They qualify for calibration and adjustment of Current Probes.
-
Product
Through Hole Type AC Current Sensor
CTF-50B
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*Suitable for current measurements of feeder cable.*Measuring range:AC 0.1A～50A.
-
Product
150 A, 10 MHz Current Probe - AC/DC, 150 A rms, 500 A Peak Pulse, 2 meter cable
CP150B
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
Ultrafast Photodetector with Current Monitor, 700 - 870 nm, DC - 25 GHz, FC/PC
DXM25CF
-
The DXM25CF Ultrafast Detector is a DC - 25 GHz, fiber-coupled, GaAs-based photodetector designed for applications in the 700 nm - 870 nm wavelength range. The core element of the detector is the fiber-coupled, hermetically sealed, microwave detector module. For convenience and simplicity of use, the module is mounted inside a rugged housing that includes a rechargeable battery, current monitor circuitry, and a digital display of the DC photocurrent.
-
Product
High Current Connectors
-
Panasonic Industrial Devices Sales Company of America
Panasonic’s offering includes various High Current Board-to-Board Connectors suitable for applications that require a connection to a power source/battery. These High Current Connectors have low mated height profiles, high reliability, and are manufactured with Panasonic's Tough Contact technology.
-
Product
PXI/PXIe Wide Current Range Multiplexer Module, Quad 3-Channel, 2-Pole
40-514-103
Multiplexer Module
The 40-514-103 (PXI) and 42-514-103 (PXIe) are low density multiplexers in quad 3-channel, 2-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
Product
Instrument Transformer Testing
-
HAOMAI Electric Test Equipment Co., Ltd.
Testing for current and voltage/potential transformers to ensure reliable and accurate operation and avoid outages.
-
Product
Transformer Turns Ratio Meter
TTRM 101
-
SCOPE introduces state of the art precision single phase Transformer Turns Ratio Meter (TTRM ) designed for field testing as well as factory testing of power transformers, instrument transformers and distribution transformers of all types. TTRM 101 measures only turns ratio where as TTRM 102 along with turns ratio, measures ratio deviation, phase angle deviation, magnetizing current and detects tap-position of single phase transformer in charged switchyard condition. The range of AC voltage selection offers high accuracy in measurement.Both the instrument have in-built TFT display with touch screen and thermal printer. The user friendly, simple instrument makes the testing more easy. With the touch keypad it is possible to enter required DUT information.The ratio results are displayed with % error. Internal non-volatile memory gives the provision of storing test results.Further data can be downloaded to PC or copied to memory stick through USB port provided.
-
Product
High Current Test System
-
HIGHVOLT Prüftechnik Dresden GmbH
High current test systems are used to test the thermal stability of equipment and components. The test system induces a current in the test object causing it to heat up. Therefore, the test object is designed as a shorted circuit. The high current test system measures the temperature of the test object at various points, in addition to the current. As a special feature, the temperature that the test object should reach can be specified and the amount of the current can be automatically calculated by the HIGHVOLT test system.
-
Product
30A, 100 MHz CURRENT PROBE, BNC, AC/DC, 30A rms, 50A Peak Pulse
T3CP30-100
-
30A, 100 MHz CURRENT PROBE, BNC, AC/DC, 30A rms, 50A Peak Pulse.
-
Product
Current Transformers
-
A range of ring type current transformers suitable for primary currents from 1A-5000A with 1A or 5A secondaries. This standard range of measuring and protective current transformers is available as resin coated or tape wrapped.
-
Product
High Speed Response, High Accuracy DC Leakage Current Sensor
DCZCT-20CDHL
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Low DC current measurements.*DC1mA～200mA*High accuracy.*±1%F.S ±10mV*Least influence of magnetization.*Less than DC1mA in current level*Convenient +5V single polarity power supply.*Reference voltage (Vref) terminal is equipped.
-
Product
Clamp type AC Current Sensor／for Power Monitor
ZCT-33
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 0.1A～150A*Current measurements of feeder
-
Product
AC Current Shunts
CSA Series
-
Ohm-Labs’ CSA series of ac current shunts are designed as laboratory standards for ac current measurement up to high frequencies.
-
Product
Magnetic & Current Sensors
-
From the International Space Station to a simple electronic compass, we can provide a solution to meet your magnetic semiconductor needs. The F.W. Bell® product line was founded in 1944. Since then we have been a pioneer in developing instrumentation to measure electric current and magnetic fields.
-
Product
Current Probe
-
Vernier Software & Technology, LLC
Simplify your experimental setup with the Go Direct Current Probe. It connects wirelessly via Bluetooth® or wired via USB to your device. The wireless connection eliminates additional cables that can clutter the lab bench. Capture small currents like those produced by a magnet falling through a coil.
-
Product
PXI/PXIe Wide Current Range Multiplexer Module, Single 12-Channel, 2-Pole
40-514-105
Multiplexer Module
The 40-514-105 (PXI) and 42-514-105 (PXIe) are low density multiplexers in single 12-channel, 2-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
Product
Low Current Probe/DMM
687
-
With the capability of measuring down to 1 milliamp (.001A), the #687 is a great tool for all low current applications. Especially for diagnosing parasitic drains! Clamp opening is large enough to fit over most negative battery cables. Applications: fuel injectors, fuel pumps, electric motors, battery drains, charging systems.
-
Product
Low Input Bias Current Amplifiers (<100 pA)
-
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
Product
AC / DC Current Probe, 100 MHz, 30 Arms
N2783B
Oscilloscope Probe
The N2783B current probe is an accurate and reliable solution for measuring AC and DC currents. Using a hybrid technology that includes a Hall effect sensor and an AC current transformer, the probe provides accurate measurement of DC or AC currents up to 30 Arms continuous.
-
Product
Current Transformer Tester
CTT
-
The CTT is designed to test the current transformer ratio, Phase shift, Polarity, Excitation, Saturation, Winding resistance and Insulation resistance using the voltage method in compliance with ANSI/IEEE C57.13.1 and IEC 60044-1 standards, where voltage is applied to the secondary X terminals of the current transformer.
-
Product
Split type Pulse Current Sensor
CTF-05M
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Pulse current detection for power demand meter.*Through hole type CT.*Open collector output.
-
Product
Voltage And Current Calibrator
-
Precision Mastech Enterprises Co.
A precision instrument designed to generate (source) and measure precise electrical signals.
-
Product
Multi Channel Linear Vibration Motor Current Isolation tester
BK2017
-
The BK2017 Current and Isolation Tester was designed as a single purpose machine for quickly testing up to 8 linear vibration motors at a time. You can test current and isolation without checking other characteristics of the motor. With its simple design, it is very easy to use and the results appear clearly on the screen in about half a second. And with only 2 cables to connect, it can quickly be plugged into an automatic loader/sorter for even faster results!
-
Product
PXI/PXIe Wide Current Range Multiplexer Module, Dual 6-Channel, 2-Pole
42-514-104
Multiplexer Module
The 40-514-104 (PXI) and 42-514-104 (PXIe) are low density multiplexers in dual 6-channel, 2-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
Product
- RS-232 to Current Loop Converter
Model 65A
-
FEATURES: Active/Passive Loops; 20 or 60 mA. Operation; DC To 19.2 KBPS; Half/Full Duplex; Optically Isolated; DTE/DCE Selectable. The Model 65A is a small, versatile, RS-232 to Current Loop Converters for use with teletypes or computers providing local terminal input via a 20mA. (or 60 ma.) current loop. The Model 65 includes a wall mounted transformer and internal power supply circuitry.
