Platinum Resistance Temperature Detectors
offer precision; accurate, repeatable, stable and linear thermometry.
See Also: Platinum
-
Product
Intrinsically safe humidity and temperature transmitter
T3110Ex
-
Built-in relative humidity, temperature sensors. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
RTD Based Temperature Data Logger
RTDTemp101A
-
The RTDTemp101A is one of MadgeTech's newest data loggers. It is part of a new series of low cost, state-of-the-art datalogging devices. MadgeTech has taken the lead in offering the most advanced, low cost, battery powered data loggers in the world today.
-
Product
Fixed Probe Temperature / RH
S.TO1 / S.TO2
-
Fixed horizontal interchangeable temperature and humidity probes with SICRAM 2 module for active transmitters, humidity and temperature regulators series HD2717T and HD2817T.
-
Product
Flow Detector with Pressure Loss Compensation Function
FP-213S / FP-2140S
-
The Volumetric Flow Detector FP-213S, FP-2140S are volumetric flow detectors, used in combination with the Digital Flow Meter FM/DF series, for precision measurement of fuel flow such as gasoline, light oil and kerosene.They are suitable for those who want to evaluate the engine performance by measuring the minute flow rate of a small engine and making the fuel supply pressure as close as possible to the actual vehicle state.
-
Product
PXIe-4353, 32-Channel, 24-Bit PXI Temperature Input Module
781348-01
Analog Input Module
32-Channel, 24-Bit PXI Temperature Input Module—The PXIe‑4353 is a thermocouple input module that provides integrated data acquisition and signal conditioning for temperature measurements. The PXIe‑4353 includes increased accuracy and synchronization features for scalable measurement systems from low‑ to high‑channel counts. The high accuracy is attributed to the NI TB‑4353 isothermal terminal block that optimizes thermal conductivity between the thermocouple terminals and the cold-junction compensation (CJC) channels. The PXIe‑4353 has two auto zero channels for offset compensation as well as open thermocouple detection to identify disconnected thermocouples.
-
Product
CBRNE Detectors
-
Investments in intellectual horsepower, research and development; enable Bruker to offer a wide range of products with a broad technological base and high end instrumentation
-
Product
Work Area Voltage Detectors
-
*Warns of high voltage electric fields using WAVi technology - Work Area Voltage Indication*Visual and audible warning indicates the location of energized fields in a red-yellow-green sequence*Detectors communicate with each other within a mesh network*Remotely control detectors through the Lookout mobile app*Battery life of up to 500 hours in Monitor mode and up to 8 hours in Alert mode*Durable water-resistant housing
-
Product
Temperature Cycling
-
Reltech provides a full capability for Temperature Cycle testing as part its full turn-key solution to package level qualification testing. Our Temperature Cycling system type Espec TSA11-A, two zone (-65°C to +200°C) vertical movement system, provides an exceptional recovery time of less than 5 minutes without the need for any auxiliary cooling.
-
Product
Digital Temperature Switch
TS
-
The TS Digital Temperature Switch is designed to regulate many heating and cooling applications. Easy programming via the tactile front keypad enables quick setup of the 12 parameters for simple, reliable operation.
-
Product
Energy Detector Laser Energy Meters
11QE25-LP-S-MB
-
11QE25-LP-S-MB energy detector provides a unique combination of high damage resistance and high speed. It also offers very good linearity with power and a versatile mounting system. It is right for many pulsed lasers. It is right for many OEM, manufacturing and laboratory uses.
-
Product
Fixed Digital Gas Detector
OLCT 10N
-
Teledyne Gas & Flame Detection
The OLCT 10N is a digital combustible gas detector designed for to detect combustible, toxic gases or oxygen. Intended for use in combination with the MX 16, MX 32 and MX 43 controller, the OLCT 10N provides a fast and accurate response.All transmitter information is received by the controller in less than 1 second.Non-intrusive operator interface requires only a simple magnetic wand and allows one man calibration without opening the enclosure.
-
Product
Digital Temperature Sensor
ZET 7021
-
Digital temperature sensor ZET 7021 is designed for measuring temperature of liquid, solid, gaseous and granular mediums, which are safe for the material of thermocouple casing. Application spheres: heat power energy, chemical and metallurgical industry.
-
Product
Walk-in Environmental Chamber for Temperature Humidity Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's walk-in environmental chamber for temperature humidity testing is perfectly meet the large size test application that require high temperature and high humidity. The walk-in chamber is constructed with structural steel, so it is able to test the large components and products. Various optional function available for different test standard and requirement.
-
Product
Infrared Combustible Gas Detector
SMC 4101-28
-
The SMC 4101-28 IR Gas Detector is a ruggedized instrument designed specifically for monitoring methane in high-vibration environments.
-
Product
Temperature & Pressure Gauges
-
An instrument or device for measuring the magnitude, amount, or contents of something, typically with a visual display of such information.
-
Product
High Temperature Self-Supporting Furnace Extensometers (1200 C)
Model 3448
-
Jinan Testing Equipment IE Corporation
Epsilon developed this unique high temperature extensometer for testing metals, ceramics, and composites at the high temperatures produced by furnaces and induction heating systems. A combination of features make these extensometers easier to use and better in performance than other similar high temperature extensometers.The units are held on the specimen by light, flexible ceramic fiber cords. These make the extensometer self-supporting on the specimen. No furnace mounting brackets are required. The side load on the test sample is greatly reduced because of the self-supporting design and light weight of the sensor. Most materials testing furnaces with a side cut-out for an extensometer will readily accept a Model 3448. For induction heating systems, a different ceramic cord placement allows the extensometer to easily pass between the coils.The combination of radiant heat shields and convection cooling fins allow this model to be used at specimen temperatures up to 1200℃ (2200°F) without any cooling. An optional tiny air fan does enhance stability at the highest temperatures and is recommended for the highest accuracy and for tests with small elongations. The fan comes with a magnetic base for support so it can be mounted at any convenient location near the extensometer. Fan cooling is not generally needed for induction heated systems. High purity alumina ceramic rods are used. These are available in lengths as required to fit your furnace. A spare set is included with every extensometer. Specify chisel, vee chisel or conical contact points as desired.Most units operate equally well in tension and compression. Thus tensile, compression and cyclic tests like low cycle fatigue can all be performed with a single unit.For vacuum furnaces, special models are available. Epsilon can also provide a radiant heat transfer cooled version. This requires that the extensometer module be surrounded by a water cooled enclosure with a front slot for the ceramic rods.
-
Product
Temperature Sensor
96000
-
The 96000 Temperature Sensor is a low-cost device that provides a simple, effective way to prevent damage and downtime caused by overheating of equipment. In monitoring equipment temperature, the sensor detects a potentially damaging or hazardous condition and alerts personnel to take corrective action. Application areas include bearings, gear boxes and motors.
-
Product
RH, Temperature and CO2 Transmitters
HD46… Series
-
The instruments of the HD46… series are transmitters, indicators and regulators suitable for measuring and monitoring the following environmental parameters, depending on the model:
-
Product
Loading Rheostats (Resistive Load)
-
Supreme Instrument Laboratories
Loading Rheostat is a device specially designed to meet the requirements of Engineering Laboratories, Electrical Test Rooms and Industries. It is used for loading transformers, power generators, supply mains etc. neatly and efficiently. It can also be used advantageously for regulating current and adjusting voltage besides its application for calibrating meters and thus eliminating the need for graded rheostats.
-
Product
5mA High Accuracy Ground Fault Detector
HA-GFD
-
Our HA-GFD Current Probe is our most sensitive current probe, measuring down to 5 milliamps. Ideal for measuring leakage current and ground faults. Dual range allows measuring up to 200 amps in high accuracy.
-
Product
Millwatch Carbon Monoxide Detector
-
Advanced system giving early warning of potential fires by detecting tell-tale carbon monioxideSpecially designed for fire detection on mills and pulverizers for coal and biomassContinuous self-checking of measurement integrityTailored to each application/plantStandard analog and discrete contact outputs
-
Product
Portable Sulphuric Acid Dewpoint Temperature Monitor
-
The fuels used in boilers, such as coal, heavy oil and natural gas, contains S. during the combustion process, S and O₂ form SO₂, and a small amount of SO₂ is converted into SO₃ under catalysis of Fe₂O₃, V₂O₅ and other catalysts. Under normal circumstances, the volume of SO₃ in the boiler flue gas is 1×10-6～50×10-6, and the water vapor is about 10%. When the temperature of the flue gas is below 200°C, SO₃ and the water vapor are completely combined into H₂SO₄ vapor. A small amount of H₂SO4 vapor will significantly increases the acid dew point. When the surface temperature of the boiler heat exchange equipment is lower than the flue gas acid dew point, the H₂SO₄ vapor will condense on the surface to become sulfuric acid solution with a concentration of about 80%, which will adhere to the surface of the heat exchanger and cause acid corrosion. Typical equipment that is prone to corrosion includes air preheaters, induced draft fans and flue walls.
-
Product
Planar-Doped Barrier Diode Detector, 0.01 to 18 GHz
8474B
-
The Keysight 8474B is a high-performance detector using a gallium arsenide, planar-doped barrier detecting element. It features extremely flat frequency response over its entire band of operation and very good frequency response stability versus temperature. The Keysight 8474B is also very rugged with high resistance to ESD damage. The Keysight 8474B detectors are available with 0.01 to 18 GHz and a type-N connector. This detector offers options for optimal square-law loads (Option 102) and for positive polarity output (Option 103). Because the unit-to-unit frequency response tracking of these devices is typically better than plus or minus 0.3 dB, no matched response option is offered.
-
-
Product
Multi-Angle Light Scattering Detectors
-
Since the 1990s Postnova has been a leading innovator and developer of special advanced online Light Scattering solutions for coupling with chromatographic separation systems. The first model was the PD2000 - Static Light Scattering detector for coupling with Asymmetric Flow FFF. Later on the models PN3020 SLS and PN3070 MALS have been launched. Based on these over two decades of practical experience, Postnova has collected a unique competence in the area of Laser Light Scattering and has developed the unique PN3621 MALS - Multi-Angle Light Scattering detector series. The model PN3621 MALS is a completely new type of high performance MALS detector system with a unique range of specifications.
-
Product
Thin Film Based Thermopile Detector: 1 Channel
DR46 Compensated
-
A one-channel compensated thin-film thermopile in a TO-8 package. The active area and compensating element area are 4mm x 0.6mm each. Offers high output with very good signal-to-noise ratio. Internal aperture minimizes channel-to-channel crosstalk increasing sensitivity.
-
Product
High Temperature Operating Life
7000 Series
-
With ever decreasing geometries, the way we perform HTOL requires careful consideration. In lower geometry device leakage currents are not only higher but vary greatly. Temperature control at DUT level – required to achieve correct junction temperature at every DUT. For higher geometries, HTOL can be performed in a more traditional way but with devices consuming more power, the ambient temperatures required varies greatly. Multiple temperature zones are required – multi zones system or multiple smaller HTOL systems.
-
Product
Hot Temperature Hardness Tester
1200C
-
Rtec high temperature hardness tester is used to do high temperature materials testing up to 1200C. To prevent oxidation of tip and the samples the high temperature indenter comes with sealed chamber with inert gas. High resolution programmable down force control and XY stage allows to do multiple indents on same or multiple samples with ease.
-
Product
Active Bat Detectors
-
The all-in-one device designed for active bat detection and recording.
-
Product
Modular Linear Detector Arrays
X-Scan M
-
X-Scan M series makes quick and accurate inspection of large-scale objects easy. The modular linear detector arrays are scalable to different inspection system lengths up to 4.1 meters with one controller and single Gigabit Ethernet interface. With network connected units even longer scanners can be built efficiently for high-energy applications.
