Fiber Couplers
Split or connect light from fibers.
-
Product
Fiber Acceptance Test Kit
23005
-
The unique design of the splice accommodates either 125um or 140um fiber and any size buffer up to 900um. The precision made splice holder firmly holds the pigtail in position without causing stress on the fiber. The low viscosity index matching liquid has an indefinite shelf life and allows for an easy glide of the bare fiber into the splice. Within seconds, a fiber acceptance reading can be made with an OTDR or test set. Low loss with minimum back reflection can easily be achieved for more accurate signatures. Other applications for this kit: splice training aids, bare fiber adapters, and temporary splicing.
-
Product
Fiber Identifier & VFL
-
Are designed to non-invasively identify continuous-wave signals in fiber optic cables. They are low cost, hand-held tools.
-
Product
Optical Fiber 1×8 Switch
OFSW - 1 × 8
-
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW- 1×8 is a 1×8 prism optical switch. It can support 1 optical fibers input and 8 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
Product
Fiber Optic Network Simulators
SIM-2FON-25
-
Vconsole fiber optic network simulator is custom built portable unit intended to simulate installed fiber optic facilities. Vconsole will design and build custom unit exactly to customers specification. The enclosure is capable of housing an individual spool with up to 100km of fiber. We will build each unit to client unique needs with custom fiber types, lengths, and connectors. A full range of connectors are available including SC, ST, FC, and LC types.This product is ideal for latency testing, product development and training and educational needs.
-
Product
Couplers, Repeaters, Bus Switches, Connectors, Cables & More
-
Accessories for the MIL-STD-1553 data bus are as much of an interface as the communication card. Therefore at Excalibur we provide a full line of accessories for the MIL-STD-1553 data bus that include, Box/Inline Couplers, Repeaters, Bus Switches, break out boxes, connectors, terminators, transformers and custom cable assemblies. Excalibur uses only premier quality parts from known manufacturers. We constantly test our products to meet our higher standards.If you have a need for an accessory product for your card and it is not listed please contact us to see if it is a product we should be supporting.
-
Product
Fiber Optic Visual Fault Finder
VFF5
-
Used to verify continuity, test and find breaks in fibre links, locate pinched fibre strands in termination cabinets, or anywhere fibre optic cables are terminated and subject to mechanical damage.
-
Product
Single 4 Ch Fiber Optic Multiplexer
40-810-014
-
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or multi- mode fiber. A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
Product
Single Fiber Bi-Direction EDFA
HA8000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HA8000 series, is a bi-directional fiber amplifier with high-quality. It can transmit and amplify downlink and uplink signal on one fiber. It offers an economical solution to network operators when utilizing the existing fiber source, upgrading networks and providing bi-directional VAD business.
-
Product
MXI-Express Cable, Gen 1 x1, Fiber Optic, 10m
778959-10
-
MXI-Express Cable with Communication Levels up to Gen 3 x8 - The MXI-Express Cable connects a host interface to a PXI or PXI Express chassis. You can also use it for data communication between multichassis systems. NI offers it in different MXI communication levels and lengths.
-
Product
Multi Mode Fiber Optic Rotary Joints
-
Multi Mode Fiber Optic Rotary Joints (FORJ) can be supplied as a stand alone product with customized features (wavelength, connectors, fiber).
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 62.5/125 Fiber
40-852A-118-M62.5-HI
-
The 40/42-852A-118-M62.5-HI is a PXI/PXIe 8-channel multiplexer with FC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
High Power Fiber Optic Visual Fault Locator
VFL-700
-
Shanghai Fibretool Technology Co.,Ltd.
The VFL-700 is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in an optical network during and after installation.
-
Product
4 Ports 1GbE Fiber Bypass Network Management Card
NMC-0120
-
Ideal for network segmentation applications and inline security monitoring. 1x Intel® I350_AM4, 4 x LC(SX or LX) fiber connectors with fiber bypass module, 1 x PCIe 2.0 x4, Gen2.
-
Product
1 Channel VGA Over Fiber Transmitter and Receiver Extender
L-1VGA-FE
-
The QuestTel L-1VGA-FE Fiber Optic Transmitter and Receiver provides long haul transmission of high resolution VGA and Audio control signals over a single fiber up to 20km.
-
Product
Fiber Splitters & WDMs
-
Wuhan Sunma Technology Co., Ltd.
Optical Splitter is used to split the fiber optic light into several parts at a certain ratio. It is an important component used in Passive Optical Network (PON), therefore also called PON Splitter. There are mainly two kinds of PON splitters: one is the traditional fused type splitter known as FBT Coupler or FBT WDM splitter, which features competitive price; the other is the PLC Splitter based on the PLC (Planar Lightwave Circuit) technology, which has a compact size and suits for density applications. SunmaFiber provides both PLC splitters and FBT coupler splitters for EPON/GPON Systems.
-
Product
C-Band Separate Raman Fiber Amplifier
RFA5000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
C-Band Separate Dispersion Compensation Raman Fiber Amplifier
DRA5228/F
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Raman Fiber Amplifier (RFA) utilizes the optic gain in the Stimulated Raman Scattering (SRS) in the optical fiber and realizes the amplification of the signal optic. FRA, with very low equivalent noise and a wide gain scope, can further widen the gain bandwidth by adopting multi-wavelength optical bump, which represents the development direction of the new optical fiber amplifier.
-
Product
Fiber Optic Light Sources
-
Fiber optic light sources are a necessity for performing optical fiber network testing to measure the optical fiberal loss for both single mode fiber cable and multimode fiber cables. They are designed to cover a variety of wavelength ranges to suit all optical testing needs and usually the optical light sources are used with the optical fiber power meter to test the fiber system loss. Light sources are offered in a variety of types including LED, halogen and laser. Usually the optical light source is used with the optical fiber power meters, they act as an economic and efficient solution for the optical fiber network works.
-
Product
Powerful 1 µm Femtosecond Fiber Laser
FemtoFiber ultra 1050
-
The FemtoFiber ultra 1050 is part of TOPTICA's third generation of ultrafast fiber lasers. The system delivers laser pulses of 90 - 100 fs in duration at a central wavelength of 1050 nm. Using a power amplifier the system provides more than 5 W average output power. It is a compact femtosecond laser system with turnkey operation and cost-effective design.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber, FC/PC Connectors
42-850A-114
-
The 40/42-850A-114 is a PXI/PXIe 4-channel multiplexer with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
Fiber End Face Interferometer
-
Thorlabs' GL16 End Face Interferometer measures and images the end face geometry of single- and multi-fiber connectors. A non-contact technique called scanning white-light interferometry (SWLI) provides high accuracy, repeatability, and reliability for fiber connector testing, particularly for pass/fail testing using IEC or Telcordia requirements. The system can be controlled locally through the touchscreen display or remotely through a browser-based application (see Software tab for details), allowing it to be easily integrated on the production floor.
-
Product
Optical Fiber Splicing Tool Kit
SAT-02B
-
Shaanxi Aitelong Technology Co., Ltd
SAT-02B Tool kit is wonderful for optical fiber fusion splicing. It includes the most frequently required tools for preparation and cleaning optical fibers before cleaving and splicing. And well fits to Aitelong model SAT-17S and SAT-17M fusion splicers.
-
Product
6FE+2x100M Multi-Mode SC Fiber Port Industrial Managed Ethernet Switch
EKI-7708E-2MI
-
Provides 6*FE ports with auto MDI/MDIX, Provide 2x100M SC Multimode 2km ports, Support 10/100Mbps auto negotiation. Support jumbo frame transmission up to 10k, Provide slim size, DIN-rail with IP30 metal mechanism, Support redundant 12V~48V DC power input and P-fail relay.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 62.5/125 Fiber, FC/PC Connectors
42-850A-114-M62.5
-
The 40/42-850A-114-M62.5 is a PXI/PXIe 4-channel multiplexer with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
Fiber Optic Pressure Seals
-
Columbia Research Laboratories
Fiber Optic Pressure Seals are designed to provide a safe, convenient, reliable method of exiting fiber optic data lines through a structure while preserving the integrity of either a pressure or vacuum environment.
-
Product
Directional Coupler
DCZ-XXE/Y
-
The DCZ-XXE/Y directional couplers are used for extracting or introducing RF power flow in a transmission line withoutdistortion of signal characteristics. The directional couplers are available in 3, 6, 10, 15, 20 dB coupling values and30 - 35 dB minimum directivities*. 4-ports directional couplers are available in bi-directional (BDC4-XXE/Y) and dual-directional(DDC4-XXE/Y) configurations.
-
Product
Optical Fiber Identifier
-
OrienTek Optical Technology Ltd.
Optocal Fiber Identifier Economical Solution for Integrated Fiber Preparation Tool Demand● 4 easy-change chucks for:bare fiber, patch cords & ribbon fiber● Identifies 3 common test tones● Identifies dominant traffic direction, audible alarm● Approximate core power reading● Low false detection & insertion loss● Very easy to operate● Battery low indication
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber, FC/PC Connectors
40-850A-114
-
The 40/42-850A-114 is a PXI/PXIe 4-channel multiplexer with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
6GE+2G Single-Mode Fiber Port Unmanaged Ethernet Switch, -40~75℃
EKI-2728SI
-
Provides 6 x 10/100/1000 Mbps Ethernet port with RJ45 connector, Provides 2 x 1000 Mbps fiber port with SC type connector for 1000Base-SX/LX device. Supports MDI/MDI-X auto crossover, Supports Auto-Negotiation, Supports redundant 12 ~ 48 VDC and 24VAC power input.
-
Product
Optical Fiber Identifier
TM301
-
TM301 Optical Fiber Identifier (Live Fiber Detector) is an essential instrument for the installation and maintenance of optical fiber projects. It can easily detect any spot of SM fiber cables. Through inserting a 1310 or 1550 modulated signal into the fiber, it is used to indicate the direction of the transmitting signals, find and locate the specific fiber without interrupting the normal work during the installation, cabling and maintenance.
