Near-field Scanning Optical Microscope
Near-field Scanning Optical Microscope
-
Product
4-Port Serial Interface, Modular, With/Without Optical Isolation, 3.3V
CPCI-7500
-
*This Model has a 37-pin D-Sub male connector*RS232, RS422, RS485, 20 mA Current Loop*Modular structure through SI modules*With or without optical isolation*Mode configuration free for each port*128-byte FIFO-buffer, common interrupt*Transfer rate programmable up to 115,200 Baud*Option: up to 1 MBaud for RS485 and RS422*Automatic direction recognition for RS48*Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)*Transmission mode asynchronous, full, half duplex*Transfer rate: progr. up to 115.2 kBaud up to 1 MBaud on request*Protocol: 5, 6, 7 or 8-bit character 1, 1? or 2 stop bits*Parity: even, odd, none, mark or space*Interrupt lines: automatic through BIOS
-
Product
Portable Optical Power Meter
CARY-PM300
-
The CARY-PM300 portable Optical Power Meter is a newly designed fiber optic tester,which aims at the installation, engineering acceptance and maintenance of fibernetwork. Combined with CARY-LS300 handheld optical light source, it offers a quickand accurate testing solution on both SM and MM fibers.
-
Product
DCA-M High-Accuracy, Low-Cost Solution for Optical Waveform Analysis
N1090A
Oscilloscope
The N1090A DCA-M builds on that legacy by using the high-performance elements of 86100 and 86105C. It can be configured to perform thorough optical transmitter compliance tests at a variety of standard data rates from 1.244 to 11.3 Gb/s and come with 20 GHz electrical channel in option.
-
Product
PXI Single 8 Channel Optic Mux MU
40-852-318
Fiber Optic Switch
The 40-852-318 8-channel multiplexer is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
PXI Express High Speed Optical FPGA Board
HSS-8324
-
The Conduant HSS-8324 Optical FPGA board provides the user with a hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PXI Express (PXIe) interface and its 24-lane optical interface. The PXIe interface provides a theoretical maximum throughput of 8GB/s (simultaneous in and out).
-
Product
AGC, SNMP, RFoG FTTB Optical receiver
RFoG4002, RFoG4004
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai RFoG4002 ( two-port ), RFoG4004 ( four-port ), is a type of high-grade AGC, Network management, RFoG FTTB outdoor optical receiver. Various operating parameters of machine are microprocessor-controlled, LED display. Through the keys of machine can adjust and set EQ、ATT. Optional network transponder, implement remote network management. Large dynamic range of optical AGC characteristics, RFoG4002 ( two-port ), RFoG4004 ( four-port ) high output ,for FTTC, FTTN fiber access network. As a unit of CATV network RX, is a high performance, highly flexible, cost-effective CATV optical receiver.
-
Product
Semiconductor Manufacturing Optics
-
No lithography without optics. No semiconductors without lithography. Without semiconductors there would be no microchips, without microchips no computers – no high-tech products. As an OEM (Original Equipment Manufacturer) supplier, ZEISS enables the semiconductor industry worldwide with optics and other optical modules.
-
Product
Optical Inspection
3D AOI
-
In contemporary electronics manufacturing, automatic optical inspection (3D AOI) is an established component of quality control. A company purchasing a 3D AOI system wants to ensure that it is manufacturing its electronic products in the very best quality and can guarantee they will have a long service life. The Viscom systems feature superlative 3D and software attributes to deliver excellent measurement accuracy and exceptional image quality. Our 3D AOI systems are designed for simple programming and can also be flexibly adapted to new requirements, allowing them to easily accommodate fast product changeovers as well as large production quantities.
-
Product
Industrial Microscope Systems
-
Below you can see two industrial microscope systems which can be created using our components. Many other automated microscopy systems are possible using our components.
-
Product
Polarization Lambda Scan Software License
N7700100C
-
Enables polarization-dependent swept-wavelength multichannel measurements with the PAS LS engine and PAS IL/PDL engine, as well as measurements without varying polarization with the PAS LS engine and PAS FSIL engine.
-
Product
Optical Identification
-
Application areas of the 1D/2D code reader range from product tracking and product control to product identification.The sensor can read 1D and 2D codes regardless of their position. Even if up to 25% of the code information becomes damaged or soiled, it is still read correctly. The reader can also be used for optical character recognition (OCR), e.g. in order to identify products based on type labels or serial numbers.
-
Product
Optical Profilometers
-
Profilm3D® and Zeta™ optical profilometers provide fast, easy, non-contact solutions for 3D surface topography measurements. Our portfolio of optical profilers supports a variety of measurement techniques, including white light interferometry, True Color imaging and ZDot™ confocal grid structured illumination. KLA Instruments can help guide you to the right optical profiler solution for your unique needs.
-
Product
FOV Micro Measuring Microscope 4.0
-
The new ultra-compact digital micro measuring microscope from Opto is the perfect tool for on-site measurements in production.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode
40-850A-314-M62.5
Multiplexer Module
The 40/42-850A-314-M62.5 is a PXI/PXIe 4-channel multiplexer with MU (mini SC) connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Variable Optical Attenuators
-
Nanning Xionghua Photonics Technology
Variable Optical Attenuator by Xionghua Photonics
-
Product
Pluggable Optical Line System
POLS
-
Use our compact pluggable modules to provide up to 8 DWDM channels to enable high-capacity optical inter-datacenter links for internet service and cloud hosting providers.
-
Product
SM & MM Quad Optical Loss Test Set
KI2724-INGAAS
-
A SM & MM Quad Optical Loss Test Set used to test power, insertion loss, continuity and faults on multimode and single mode fiber optic systems at 850 / 1300 nm & 1310 / 1550 nm. In a small package, it is a powerful fiber optic multimeter / OLTS with improved test flexibility and productivity.
-
Product
PXI Single 8 Channel Optic Mux FC/APC
40-852-018
Fiber Optic Switch
The 40-852-018 8-channel multiplexer is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
3D Optical Profilers
-
ZYGO's 3D Optical Profiler instruments enable precise, quantitative, ISO-compliant, non-contact surface measurement and characterization of micro- and nano-scale surface features, capturing up to two million data points in just seconds. Applications range from topography and waviness to roughness and microstructure characterization on samples as that vary from ultra-smooth sub-angstrom optical surfaces, to extremely rough and diffuse 3D printed surfaces.
-
Product
Multi-wavelength Measurement Optical Time Domain Reflectometer
MT-7300 Plus
-
Guangzhou Wanglu Communications Co., Ltd.
● 32/30dB high dynamic range● ≤2m extra-short event dead zone● 0.05m high distance resolution,128k sampling points● Fast auto measurement, one-button operating● Test up to four wavelengths with a single unit ● Communication light check automatically● Remote function via Ethernet● USB interfaces, supporting USB stick and printer and direct cable download to PC via ActiveSync● Supporting Bellcore GR196 file format in writing or reading● Built-in lithium battery with high capacity for over 8 hours of operating life● Integrated Visible fault locating (VFL)
-
Product
X-ray Optics
-
Do you want to shape your X-rays to a tiny point? Then our X-ray optics can help you. Benefit from 30 years of know-how in the development and manufacture of customized optical components for demanding applications. Our high-precision optics offer unsurpassed performance and enable the best results in a wide range of applications.
-
Product
Optical Distance Sensors
-
Leuze electronic GmbH + Co. KG
Optical distance sensors perform different measurement tasks in various applications with varying requirements with regard to accuracy, resolution and size. To meet these diverse needs, the operating principles of triangulation, propagation time measurement and phase measurement in different sensor sizes and specifications are covered by a wide range of optical distance sensors.
-
Product
Switchable Optical Interleaver
-
In a switchable interleaver, there are two operation modes: *Mode A: All pass *Mode B: InterleaverIn Mode A, the system operates at any channel spacing, in which all channels pass through the device and output from one of the two output ports as if there is no extra device inserted. When the system is switched to Mode B, the device operates as a normal optical interleaver, such 50-100GHz interleaver. The working principle is schematically shown below. In Mode B, the device could be a standard symmetric interleaver, or an asymmetric interleaver. Channel spacings are not limitted to 50-100GHz. They can be any frequency pair: between N-GHz and 2N-GHz.
-
Product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass
40-860A-522-M
Multiplexer Module
The 40/42-860A-522-M is a PXI/PXIe dual insert/bypass switch with ST connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
Chromapoint Large Slope Angle Optical Heads
EVEREST
-
Sciences et Techniques Industrielles de la Lumière
Born from the last STIL innovation, EVEREST chromatic confocal sensor head contains the best of research and development in terms of sensors.EVEREST series offers an extended measurement range with the highest performances.
-
Product
Measuring Microscopes, Image Processing
COMEF
-
Optik Elektronik Gerätetechnik GmbH
Image processing system.
-
Product
Differential Scanning Calorimeters
MicroCal DSC Range
-
The "Gold Standard" for structural stability analysis of biotherapeutics, biological macromolecules and polymers in solution. Are microcalorimeters are powerful tools which enable characterization of the thermal stability of proteins and other biomolecules, primarily for biopharmaceutical development and manufacture. They are used for general stability studies, for biosimilarity and batch-to-batch comparability assessment, and for the optimization of purification and manufacturing conditions. MicroCal PEAQ-DSC systems are simple to use, requiring little assay development, and no labelling or immobilization.
-
Product
Optical Sensors
-
Leuze electronic GmbH + Co. KG
Optical sensors use light in various forms to perform their detection tasks. An extensive product line is available with reliable and efficient sensor solutions for all applications that can be solved optically. Object detection for different surfaces, object sizes and colors requires various function principles, such as a throughbeam photoelectric sensor, a retro-reflective photoelectric sensor or a diffuse reflection sensor. All different operating principles are usually available in a given series (size). Universal series are also available with extended models and additional useful functions.
-
Product
Sample Pretreatment For Optical Emission Spectrometry
-
Samples are taken from molten metal, thin sheet, semi-complete or complete products. When sampling molten metal with a ladle, small quantities of molten metal are poured into a casting mold. Unnecessary parts of the sample are removed using a grinder or a cutter. As particles from a grinder may contaminate the surface of the sample, a lathe or milling machine is used (not a grinder) to cut soft samples such as white metal. If trace elements are not being investigated, a grinder or belt sander can be used. However, to minimize contamination, the grinding wheel or belt should be changed for each sample. Samples excised from semi-complete or complete products must be at least 12 mm in diameter. Small rod-shaped samples can be analyzed using special equipment.
-
Product
Precision Optics and Assemblies
-
For more than 35 years, Keysight has been designing and fabricating leading-edge optics for use in our laser interferometer systems. You can take advantage of this engineering, component fabrication, and assembly expertise and our state-of-the-art optics manufacturing facility in Santa Clara, California to deliver cutting-edge optical solutions to your customers:
