-
-
Product
Vibrating Level Switch
TF 100 Series
-
TF-100 Series is a vibrating level switch with TF-L relay output and TF-P transistor output or with TF-T current output.This level switch is designed for reliable indication of clean liquids and light slurries. It is available with Relay, Current, and PNP outputs that can be set to indicate alarm on either high level for spill prevention, or low level for run-dry protection.
-
Product
Systems
-
Datum Electronics Systems - Silo Hawk silo weighing system, Datum Hawk engine condition monitoring system, Cargo Hawk SOLAS compliant container weight verification system, and more
-
Product
RF/Microwave ATE Systems
-
Over two decades ago, In-Phase Technologies founded our company for the purpose of designing and producing reliable high quality RF and microwave Automated Test Equipment (ATE). We continue that tradition today, providing the best, world-class automated test equipment. Our system designs bring together the right combination of Commercial Off the Shelf (COTS) test equipment, custom designed and built Interface Test Adapters (ITAs), lightning fast and accurate measurement software, and the optimum user interface to make all of this technology easy to use.
-
Product
High Voltage Cable/Harness Test System
CKT1175-50
-
The CKT1175-50 is a high-voltage wiring analysis system that features a switching matrix that can be distributed around the workshop or in and around the assembly to be tested. This system is expandable in 100 or 150 test point increments to 96,000 test points, and is available with a variety of adapter cable interface connectors, with the standard being the CKT MAC interface system
-
Product
Sputtering Systems
-
Known for precision and cleanliness, Veeco Ion Beam Sputtering (IBS) systems are ideal when engineers need tight control over film thickness, composition, and optical performance. Using a focused ion beam, IBS dislodges atoms from a target, depositing them onto a surface in smooth, ultra-uniform layers.
-
Product
Compression, Paper And Pulp Test Systems
-
From basic tension and compression testing to advanced materials testing
-
Product
Satellite Signal Level Meter
Super Buddy
-
Complete more installs faster and better using the Super Buddy satellite finder meter. Be "sure of your bird" with the positive ID feature or use the automatic scan to identify the unknown satellite. The Super Buddy's geo-sensitive "Field Guide" shows you just the birds visible to your install -- ALL of them, with their individual transponders. The Super Buddy even gives the elevation and azimuth for whichever satellite you select.
-
Product
Test System
MxDSRC™
-
The MxDSRC Test System simulates systems in the vehicle that interact with the DSRC radio module to create tests closely replicating real-world scenarios. Its integrated approach allows the DSRC components, such as RF quality and protocol conformance, to be exercised with multiple system components. MxDSRC provides a powerful and easy-to-use framework for testing your DSRC system.
-
Product
System Amplifiers
-
The perfect combination of high performance, wide bandwidth and low noise
-
Product
Test Tables / Test Consoles
-
Adaptronic test tables and test consoles are a decisive component of the adaptronic kit for the assembly of comfortable and high-quality test systems for the wiring test of manufactured cable harnesses of all types.
-
Product
Dynamic Component Test Systems
-
RedViking brings advanced engineering and proven implementation expertise to your next dynamic component test stand. We’ve designed entire fleets of multi-model and single-model test systems for new component development and production as well as military and commercial MROs. We have decades of experience building and implementing turnkey dynamic component test systems, and we’ll work with your teams virtually anywhere in the world.
-
Product
Metrology System
Atlas V
-
The new Atlas V metrology system is designed to measure several key steps that include buried features, not visible by CD-SEM and other techniques. Through remarkable improvements in the optical systems, mechanical sub-systems and software algorithms, the Atlas V system can precisely measure the very subtle variations for device parameters and reveal weak process corners for engineers to improve their process robustness in the fab.
-
Product
Dilution-Extractive System
ML675
-
The Teledyne ML®675 dilution-extractive system can be used in 40CFR75, 40CFR60, 40CFR63, and process control applications. In this system, sample is prepared for analysis by diluting stack gas with clean, dry instrument air at the probe location. Since no moisture is removed with dilution, measurements for SO2, NOx, CO, THC and CO2 are made on a wet basis.
-
Product
Level Monitoring
-
Magnetic level switches are used for the monitoring and control of liquid level in tanks. These level switches are specifically manufactured to customer specifications. The float switches are manufactured with a hermetically sealed contact which is located within the guide tube. The float sliding on the tube contains a ring magnet which activates the sealed contact in a non-contacting fashion. The sealed contacts are available as SPST (N/O or N/C) or SPDT (N/O + N/C). The float sliding up and down on the guide tube is the only moving part on the M-series magnetic float switches.
-
Product
Various Types of Automatic Hardness Testing System
-
Various Types of Automatic Hardness Testing System
-
Product
Sampling System
ASS-370
-
The sampling unit is responsible for suction air from ambient and to distribute this air without any changing to the gas-monitors. The HORIBA sampling unit is designed according ÖNORM-M5852 Type A. So an air flow monitor will give alarm information when the flow is to low.
-
Product
Transmission Performance/Endurance Test System
-
This system is suitable for vehicle drive test with only the transmission unit in combination with the real-time model calculation by the measurement/control panel and low inertial motor. Simulation test of an actual vehicle running condition can be executed by modeling engines, tires or vehicles other than transmission. The engines, tires and vehicles are modeled by MATLAB® / Simulink®, so they can be evaluated under various conditions by changing parameters or replacing models.
-
Product
MEMS Testing System
BK3010V2
-
The BaKo BK3010V2 is our updated MEMS Tester, based on our C-Mic tester, the best selling BK3010. It's small enough to carry under your arm and with a test time of under 0.5 seconds, it tests as fast as you can connect a microphone. Setting up the specifications is very easy and can be done in a few minutes. In addition, the new BK3010V2 can be connected to a computer so you can keep and view compiled data and track trends in variations in your C-Mics.
-
Product
MB-OFDM Protocol Test System
WiMedia Explorer 300
-
The WiMedia Explorer 300 is the world's first over-the-air MB-OFDM protocol test system for WiMedia Alliance's Ultrawideband common radio platform, Wireless USB protocol and Bluetooth.
-
Product
Coil Test System
CTS
-
International Electro-Magnetics, Inc.
The system is controlled by a PC using software written in Visual Basic. It offers visually oriented menus that allow easy coil configuration and test set up procedures.
-
Product
Integrated Systems
-
Innerspec’s Integrated Systems are designed to provide automated and semi-automated NDT inspections in factory environments. These systems can incorporate unique sensors, instrumentation, software, as well as customized mechanical devices to integrate the inspection system with other equipment and processes.
-
Product
Thermal Imaging System for Electronics Testing
ETS320
-
Whether the goal is product testing or scientific research, heat can be an important indicator of how a system is functioning. The FLIR ETS320 is a non-contact thermal measurement system that pairs a high-sensitivity infrared camera with an integrated stand, for hands-free measurement of printed circuit boards and other small electronics.
-
-
Product
Benchtop Test System
300 Series Benchtop ATE
-
The Circuit Check 300 Series benchtop ATE Test Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 300 Series Benchtop ATE, test procedures can become automatic, with test steps and go/ no-go limits easily programmable in common tabular form. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
Product
Radar Level Transmitter
DR7400
-
Drexelbrook DR7400 is a loop powered FMCW 26 GHz radar that offers State-of-the-Art components. The DR7400 operates over a larger bandwidth: This ensures excellent resolution and high accuracy in agitated and corrosive liquids.
-
Product
800MM 31.5In Digital Level Bevel Gauge w/ LCD Backlight Screen, Level Bubbles IP54 Standards
DL411
-
Advance Plus Trading Co., Ltd.
Model Number: DL411 Key Specifications/Special Features: 800MM 31.5INCH Digital Level with level bubbles, 2 hand shanks, LCD bright backlight display, IP54 standards 1. 800mm 31.5inch level with 2 bubbles, 800*28*64mm（L*W*H）, net weight: 700g;2. Resolution: 0.05°;3. Horizontal level measuring range: 0 to 360°;4. Accuracy: ±0.3°;5. Measures angle in degrees, IN/FT, mm/m, % slope or pitch;6. Audible tone at level, plump and setting angle;7. Automatic shut-off after 3 minutes;8. Backlight LCD;9. Self checking accuracy;10. Self calibration;11. Hold-function to freeze the measurement;12. Memory recall (9 measurements);13. 2pcs Handshanks design, easy to take and use;14. 2pcs high accuracy horizontal & vertical bubbles, clearly to check;15. Operated by DC 3V (2*LR03 AAA 1.5V batteries, not included); 16. IP54 waterproof & dusyproof industrial standard.
-
Product
Air Data Test Set System
B511
-
The BRAT Option B511 is an option to the BRAT Test System utilizing Commercial-Off-The-Shelf (COTS) equipment. The system is used to augment the existing BRAT capabilities to test rate of change of altitude or pressure.
-
Product
Automated Systems
-
The Rice Lake line of automated systems gives your system the efficiency it needs to keep up with growing business.
-
Product
Medical System
Sentinel I
-
Chroma Systems Solutions, Inc.
The Sentinel I System provides fully automated Electrical Safety Testing to IEC/EN/UL/CSA 60601-1. This system is ideal for testing medical products with one or no patient connections or low volume production where operators can manually change leads between different patient connections. This is a 5 in one Hipot test system that can test Hipot, Ground Bond, Insulation Resistance, Patient Leakage, Earth Line Leakage, Enclosure Leakage and Patient Auxiliary Leakage.
