Battery Simulation
reproduce battery performance under test conditions.
See Also: Battery Simulators
-
Product
Circuit Breaker Simulation Device
PSS01
-
PSS01 is the circuit breaker simulator，which can conduct circuit breaker simulation to test the whole secondary relay scheme together with relay test set. It is very good accessory for protection relay test kit to avoid complicated software programming to finalize the same test.
-
Product
Digital 12V Battery Tester
BT175
-
Schumacher Electric Corporation
DIGITAL TESTER FOR 12V BATTERIES/STARTER SYSTEMS/CHARGING SYSTEMSHand-held tester checks the battery, starting and charging systems with digital accuracyDigital display guides you through the testing process and shows voltage and CCALEDs indicate OK, OK & Recharge, Recharge & Retest, Weak, Bad Battery and Error For 12V SLI and VRLA/AGM/GEL batteriesAccepts rating types CCA, CA, EN, IEC, DIN and SAEOperating range: 100-1200 CCA (SAE)Testing voltage: 7-15VContents: (1) Schumacher BT175 Digital Battery Tester (1) owner's manual
-
Product
Power Supply Voltage Fluctuation Simulator
SG Series
-
Simulator to reproduce DC supply voltage variations phenomena in the vehicle environment for evaluating immunity of automotive electronics. This simulator can perform various tests against voltage variations required by ISO 16750 and other international standards. Please contact us for voltage variations testers to perform testing to manufacturers' private standards.
-
Product
Solar Simulation Systems
-
PET Solar Simulators consist of a Light Source with a built-in Lamp Power Supply. The Solar Simulator has an ellipsoidal reflector that surrounds the lamp and collects most of the lamp output. The radiation from the lamp is focused onto an optical integrator that helps produce a uniform diverging beam. The beam is diverted 90° by a mirror onto a collimating lens. Special filters are placed between the mirror and the collimating lens to shape the radiation spectra to match various air masses. The output is a uniform beam that closely matches the sun's radiation spectra for a given air mass. Various models offer different areas of illumination. Each model can be manufactured to simulate the sun's radiation for different air masses.
-
Product
Battery Voltage Supervisor
BVS
-
DV Power battery voltage supervisor – BVS, is an accurate battery voltage monitoring system that monitors the state of health of battery systems. It records important battery parameters such as battery voltage, inter-cell connection voltage, and ambient temperature. Because of that, it can be a support tool for capacity testing.The BVS voltage supervisor is an integrated system consisting of:BVS Control Unit (BVS-CU)Cell Voltage Modules (CVM)String Voltage Module (SVM) (optional)String Current Module (SCM) (optional)It is an ideal testing tool for maintenance, troubleshooting and performance tests on individual stationary batteries and battery packs in critical backup energy solutions.BVS-CU provides ambient temperature measurements on multiple locations (4 temperature channels). Overall string voltage and string current monitoring can be achieved by using an optional string voltage module (SVM) and string current module (SCM).There are two types of DV Power battery voltage supervisors:BVS – One cell voltage module measures 1 cellBVS-4 – One cell voltage module measures 4 cellsCVM modules detect cells that fail a discharge test based on monitored voltage values. As a result of that, these cells can be safely removed from the battery string.Data acquisition and analysis of data collected from the modules are available in the DV-B Win application software suite. They provide data viewing, tracking, and generation of comprehensive reports.
-
Product
8 Port BRI-U ISDN Simulator
BRI-8U
-
The unit has 8 U ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
-
Product
Tenney SafeTest™ Battery Test Chamber
-
Whether your company serves the automotive, computer, telecommunications, defense, or alternative-energy industries, you need a safe, reliable way to test batteries. The Tenney SafeTest™ system offers a comprehensive line of standard and optional test-chamber safety features that can be customized to fit your company’s battery-testing needs.
-
Product
Radar・Sensor Simulation Framework
COSMOsim
-
Millimeter Wave Radar simulator and LIDAR (Laser Imaging Detection And Ranging) simulator for Automotive sensor simulations, and also can provide 3DCG MAP for specific radar which has millimeter accuracy. Now we can only provide AMMWR and ALR to the following COSMOsim Framework. This simulator enables automotive manufacturers to simulate a driving situation by sensor-based modelling, check the recognition and control of autonomous driving, and verify the sensor-mounting positions on vehicles efficiently, which eliminates the need for test driving with real vehicles.
-
Product
Battery Cell Testing Equipment
-
Xiamen WinAck Battery Technology Co., Ltd.
The battery cycle life tester is a high-precisionsystem designed specifically for the battery cell charge and discharge testing.It is suitable for the battery cell cycle test, battery cell charge anddischarge aging test, battery cell performance test, battery cell capacitydetection test, battery cell IR test, deep-discharging test, function test ofhigh-power lithium-ion battery cells, such as EV battery module, ES batterymodule, super capacitor…
-
Product
Multifunctional Simulators
CCS600
-
Suzhou 3ctest Electronic Co.,Ltd.
CCS600 designed as a modular system is the most intelligent solution offering exactly what people need for full-compliant immunity tests against transient, surge and voltage dips. The max voltage is up to 6kV.
-
Product
Battery Module Test Equipments
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's battery test equipments series mainly for testing the battery module of Electric-bike, Electric Motorcycles, etc. These series meet the standard compliance of IEC62619, UL2580 and GB31485-2015. Including short circuit, thermal test, drop test and crush test, etc.
-
Product
Industrial Standby Battery Monitoring Systems
-
Batteries are the power storage medium for all Power Rectifier and UPS Systems. Modern Rectifiers and UPS control systems generally supply the user with only a summary of the condition of the associated power systems, however Battery Monitoring systems specifically measure, record and analyse the individual cell and battery module parameters in detail.
-
Product
Standby Battery Testers
-
Franklin Electric - Grid Solutions
A user-customizable, flexible, efficient and economical battery management tool for service providers, operations, and maintenance teams.
-
Product
Avionics Test & Simulation Software
-
Ballard CoPilot® is an intuitive, graphical software program that allows you to easily monitor, record, replay, analyze, and simulate avionics bus data. With CoPilot you can interact directly with data on multiple buses using Ballard avionics interface hardware or work with previously recorded data. This advanced program features powerful tools for development, testing, troubleshooting and maintenance of avionics equipment and systems.
-
Product
FIber Based Solar Simulator
-
Provides up to 12 suns class B non-uniformity over a 12.5 mm diameter with the A4 Light Line and class C uniformity can be achieved over 18mm diameter both with a working distance of 25 cm. Provides up to 4 suns class B non-uniformity over a 12.5 mm diameter with the A1 Light Line with a working distance of 25 cm.
-
Product
Avionics Network Simulation Systems
-
Avionics Interface Technologies
Support for up to 30 Network Interfaces (Fibre Channel & Ethernet)Time Synchronization with IRIG-B & IEEE 1588 Master ClocksFull Data Capture with time stampingData simulation with precise timing & synchronizationNetwork data replay from previously captured trafficPerform Network analysis using AIT's intuitive, easy to use, Ethernet & Fibre Channel simulation tools
-
Product
Test Device for Bicycle Batteries
ATGF 1500/PBG
-
The ATGF 1500 is a multifunctional testing instrument for bicycle batteries and accompanying battery chargers. The easy to use ATGF 1500 is suitable for battery systems of Derby Cycle, Gazelle, Simplon and ZEG. est programs: Quick Test, Capacity Test, Recalibration.
-
Product
MCDU Simulator
-
Square Peg Communications Inc.
The Multi-Function Control and Display Unit (MCDU) is an input device for the flight management system and other computer systems of modern aircraft. It consists of a screen and an alphanumeric keyboard and can be found within reach of the pilot in the cockpit of the aircraft. The operation of the MCDU is described in the ARINC 739 specification.
-
Product
CTEK Multi US 7002 Battery Charger
56-353
-
The MULTI US 7002 is the ideal battery charger for your caravan, car and boat. The battery charger is well suited for all-year use. Thanks to its SUPPLY mode the battery charger provides power even without a battery. The SUPPLY mode is indispensable when changing the battery as you avoid losing complicated program settings.Perfect for vintage car, boats with one battery, boats with start & service battery, boats with start & service bank, scooter, motorcycle, Quad/ATV, lawnmower, caravan, and tractor.Includes two interchangeable connection leads, one with clamps, and one with eyelet terminals.
-
Product
Educational Patient Simulator
EasySim®
-
The new and improved EasySim® arrhythmia simulator fits in the palm of your hand! The ultra-portable (6.6″ x 2.4″ x .5″), ultra-lightweight (10 oz.) remote control will place you on the leading edge of medical education technology. The highly intuitive design features 48 direct-access keys in a remarkably easy to use format. No codes to memorize! No fuss to set up!
-
Product
Voltage Dip, Interruption& Variation Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
PFS single phase power fail simulator simulates voltage dip, interruption and variation which are caused by power grid and transformer devices due to malfunction or sudden large change of load. It is required to test this kind of phenomena to check whether electronic and electrical device can sustain safety operating condition.
-
Product
Battery Extra Load Units
BXL Series
-
BXL is an extra load unit designed to be used with DV Power’s BLU series battery testers. However, this unit is a universal add-on device. Because of that, it is compatible, as an additional load, with any other discharge/capacity tester in the market.In case when discharge current exceeds the capacity of a single BLU device, BXL can increase the discharge capacity. There are no limitations on the number of extra load units that can be connected in parallel to the main battery tester.A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way. Also, all instruments are in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.These units can be used on any type of battery string, such as lead-acid, Li-Ion, Ni-Cd, etc. They test battery strings with voltages in the range of 5,25 – 500 V DC. On the other hand, current up to 250 A can be discharged through the BXL internal structure.The instrument simulates a constant resistance load during the discharge test. Several resistances can be set for different battery nominal voltage levels. This makes BXL extremely flexible in selecting its load capabilities.
-
Product
Test & Simulation Interface for PCI-X
PCI-X-C1760
-
Avionics Interface Technologies
HS1760/MIL-STD-1760E Test & Simulation Interface for PCI-X
-
Product
Battery Charger-Analyzer for small battery systems
Minicharger
-
The Minicharger is an instrument designed to charge, trickle charge and analyze (discharge) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries
-
Product
Flash Solar Simulators
-
Sciencetech manufactures a range of flash solar simulatorsSee the Flash Solar Simulator Overview to compare products across different product lines.
-
Product
Battery Charger Meters
-
A range of ammeters and voltmeters with tough moving magnet or polarised moving iron movements designed for low cost indication of d.c. or rectified a.c.
-
Product
AIT PXI Express Test & Simulation Instruments
-
Avionics Interface Technologies
AIT’s Test & Simulation Instruments for MIL-STD-1553, ARINC 429, ARINC 664/Avionics Ethernet, and Fibre Channel are available in PXI and PXI Express form factors and are supported by software drivers for Windows, Linux, and LabVIEW Real Time. All instruments are also supported by Software Development Kits which provide API’s for C/C++, C#, and LabVIEW.
-
Product
Mouth Simulator
BO1032
-
As consumers demand smaller devices that produce better sound and need better microphones, you need to test your microphones using more than a simple 1kHz tone. Sweep tests require a good mouth simulator that can produce a sweep with a known steady SPL.
-
Product
Battery Capacity Tester
BLU-A Series
-
The battery capacity test is performed to determine the health of a battery. DV Power’s battery load unit BLU-A is a portable, powerful, and lightweight solution for battery capacity measurement. It is applicable to any battery string such as lead-acid, Li-Ion, Ni-Cd, etc., with up to 500 V battery voltage. As a special feature, BLU100L model enables the capacity testing of a single Li-Ion cell.The capacity test is performed in an accurate and user-friendly way. Also, it is in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.Battery load unit BLU-A enables setting discharge currents up to 240 A, with a resolution 0,1 A. Furthermore, if higher currents are required, BLU-A units can be connected in parallel, or additional BXL load units can be used.The instrument offers the best power-to-weight ratio in the market. BLU-A models start from 12,8 kg / 28.2 lbs and deliver up to 28,4 kW of power.The user can select three discharge modes:Constant current,Constant power,Constant resistance.Additionally, different battery duty cycles can be simulated using user-selectable discharge profiles.The instrument monitors discharge parameters in real-time during the capacity test. A 4,3-inch touch screen display shows battery voltage, current, elapsed time, and capacity during the entire test. Also, BLU battery load unit can be used with DV-B Win software. As a result of that, a user can see a detailed numerical and graphical presentation of key parameters and can create reports in various formats.Testing with BLU-A doesn’t require a disconnection of the battery from the testing equipment.
-
Product
Open-source CAD tool to simulate 2D and 3D-ICs.
IntSim v2.0
-
Simulate and optimize 2D and 3D-ICs. Pre-silicon estimates for die size, number of metal levels, size of each metal level and chip power.
