-
product
Digital Circuit Breaker Analyzer
CT-7000 S3
The CT-7000 S3 is Vanguard’s fourth generation EHV circuit breaker analyzer. The CT-7000 S3 is available with 3 (part number 9021-UC) or 6 contact timing channels (part number 9100-UC). The CT-7000 S3 can fully analyze a circuit breaker’s performance by measuring the main contact and resistor contact time, stroke, velocity, over-travel, bounce back and contact wipes. Both contact and motion analysis can be performed on all circuit breaker operations (OPEN, CLOSE, OPEN-CLOSE, CLOSE-OPEN, and OPEN CLOSE-OPEN). The CT-7000 S3’s timing window is selectable between 1 second, 10 seconds, and 20 seconds.
-
product
Defibrillator Analyzer
DA-2006
The DA-2006 is a microprocessor-based analyzerthat is used in the testing of defibrillators. It measuresthe energy output and provided information about thepulse. It is used on manual, semi-automatic and automatic defibrillators with monophasic or biphasic outputs.
-
product
Fuel/Other Analyzers
Our products are used to test fuel in a couple of ways. Fuel blending is the process of ensuring a fuel has the desired composition in terms of relative concentration of components. Testing fuel for contamination ensures that the equipment that burns the fuel will not suffer damage from impurities in the fuel.
-
product
TOC Combustion Analyzer
Torch
The Torch is considered the premium TOC combustion analyzer due to its many useful features and automated analysis processes. For example, it makes serial dilutions of stock standards to form a calibration curve and auto-dilute samples with concentrations above the calibration curve. The Torch software has built-in diagnostic and troubleshooting capabilities. For a luxury but affordable TOC combustion analyzer that you can just load and walk away, look no further than the Torch. You won't regret it!
-
product
Spectrum Analyzer
SA-S
RF Frequency Range: 1 Hz to 4.2 GHz. Low noise amplifier available above 500 KHz. Wide dynamic range: -151 dBm to +10 dBm. Resolution bandwidths (RBW) of 0.1 Hz to 250 KHz and 5 MHz. Includes a High Dynamic Range Measuring Receiver. 0.25 dB relative accuracy. 0 dBm to -125 dBm, 150 KHz to 1 GHz. 0 dBm to -115 dBm, 1 GHz to 4.4 GHz. Adjustable digital audio filters. Accurate AM and FM measurements
-
product
Network Analyzers
MPR1 Series
CurrentNeutral currentVoltage (Phase to Phase, Phase neutral)Active, Reactive and Apparent powerFrequencyActive PowerReactive PowerApparent PowerCos φPower FactorTotal Active PowerTotal Reactive PowerTotal Apparent PowerTotal Cos φTotal Power FactorTotal Harmonic Distortion of the CurrentTotal harmonic distortion in current from phase to phaseTotal harmonic distortion in neutral current from phase to phase
-
product
Optical power meter with Optical laser Source
Shanghai Baudcom Communication Device Co.,Ltd.
The Multimeter combines a power meter with a 2-wavelength laser source,for optical fiber network installation and maintenance. With the large capacity of data storage,it's very convenient for field testing and transfering the test results to PC through USB interface.
-
-
product
GC Analyzers
Agilent’s GC Analyzer portfolio can combine multiple methods into a single system, with proven results, and significantly reduce time required from system arrival to final calibration and validation. With our preconfigured gas chromatograph hardware and method-specific separation tools, you can spend more time focusing on sample processing than on method and system development. Our specific GC Analyzer solutions provide the components and specifications to quickly install new methods for a fast return on investment in various application areas, such as environmental, gas impurities, forensics, pharmaceuticals, dissolved gas, energy, and chemical applications.
-
product
Network Analyzer, Tester, LED
72-9450
This cable tester allows for quick and easy troubleshooting of RJ45 and USB cables. Checks for continuity, faulty wiring, open, shorts, straight through or cross pinning of cables.
-
product
Widely Tunable Ultrafast Laser System For Multiphoton Imaging
InSight X3
Spectra-Physics’ new InSight® X3™ is the third generation of Spectra-Physics’ industry leading InSight platform, specifically designed for advanced multiphoton microscopy applications. Based on patented technology1, InSight X3 features a broad 680 nm to 1300 nm continuous, gap free tuning from a single source, nearly double the tuning range of legacy Ti:Sapphire ultrafast lasers. InSight X3 delivers high average and peak power levels across the tuning range, including critical near infrared wavelengths above 900 nm for deepest penetration in-vivo. With Spectra-Physics’ integrated patented DeepSee™, the industry standard dispersion pre-compensator, the short pulses are optimally delivered through a microscope to the sample for maximum fluorescence and penetration depth. InSight X3 also has exceptional beam pointing stability, beam quality and output power stability, as well as fast wavelength tuning, making it ideal for microscopy.
-
-
product
Process NIR Analyzers
Process near-infrared (NIR) analyzers continuously measure moisture, oil, coat weight and other parameters directly in manufacturing processes for responsive process control. Common industries include wood products, tobacco, snack foods, converting, and bulk materials. A variety of sample interfaces, environmentally rated enclosures, and interface options are available for easy implementation and integration.
-
product
Wireless Signal Analyzer
WSA 300
Sage’s new series of wireless signal analyzers provide unparalleled performance for the price in an extremely portable package.
-
product
Multichannel Analyzers
Multichannel Analyzers (MCAs) are workhorse instruments in many scientific measurements. An MCA analyzes a stream of voltage pulses and sorts them into a histogram, or “spectrum” of number of events, versus pulse-height, which may often relate to energy or time of arrival. The stored spectrum may then be displayed and analyzed.
-
product
Power Quality Analyzer
PQM-711
PQM-711 power quality analyzer is an advanced product for wide type of measurements, analysis and recording of network parameters 50/60 Hz and the power quality diagnostic according to European standard EN 50160. PQM-711 is an innovative model with a wireless communication Wi-Fi , which allows for automatic pairing with the included tablet, with a large 10" touch screen. Tablet allows full operating of the analyzer, live data preview and the reading and analysis of data stored in the internal memory. With this solution, the PQM-711 is an unique device that combines the advantages of the analyzer with built-in display and typical portable analyzers (known as Black Boxes).With the tablet you can very fast checked the device under test. On the other hand, you can leave the analyzer module for multi-measurements as a typical logger without display. You can very fast diagnose the machine under test using the tablet. On the other hand, you can leave the analyzer module itself for many days measurement as a typical logger without display. PQM-711 has a transient registration with a maximum sampling rate of 10 MHz (rapid changes in voltage) and control signals. The minimum duration of the registered transient is 650 ns.
-
product
PCIe 5.0 Protocol Exerciser
P5551A
Keysight PCIe 5.0 Protocol Exerciser gives the flexibility in emulating either as a root complex or as an endpoint device when validating PCIe designs.
-
product
zeta potential analyzer
ZetaProbe Analyzer™
The ZetaProbe is the easiest to use, most accurate zeta potential analyzer available. Samples can be measured without dilution or sample preparation at concentrations up to 60% volume. Even the direct measurements of pastes, gels, cements, and other difficult materials are possible with the ZetaProbe.
-
product
Power Analyzers - Meters - Loggers
Full line of power and power quality analyzers, loggers and meters including for extending measurement ranges. The wide range of applications include electrical monitoring, harmonic detection & analysis, utility testing, energy management, power factor analysis and correction, power demand and consumption, kW measurement, industrial power systems, and commercial maintenance.
-
product
Beam Bender BK7, Fixed Horizontal-Bend Mount
E1834M
The E1834M is a beam bender that bends the incoming beam at a 90-degree angle and is designed for beam diameters of 9 mm or less. This referenced optics uses high performance horizontal mount to deliver laser beam throughout a measurement system. The 8 flexure feet are designed for stable beam pointing.
-
product
Laser Source
TW3109
Techwin(China) Industry Co., Ltd
can provide 1 to 4 output wavelengths to meet specific requirements, including the 650nm red source and the 1310/1550nm wavelengths for single mode fiber or the 850/1300nm wavelengths for multimode fiber, as well as other wavelengths according to customer needs. Together with the TW3208 optical power meter, it is a perfect solution for the fiber optic network characterization.
-
product
FieldFox Handheld Microwave Analyzer
N9913A
4 GHz max frequency Carry the world's most integrated handheld RF analyzer: standard model includes cable and antenna analyzer Expand capabilities with optional VNA, spectrum analyzer, built-in power meter, vector voltmeter, and more Save time by measuring DTF and TDR in the same sweep Simultaneously measure all four S-parameters Make accurate spectrum analyzer measurements ( 0.5 dB) without warm-up Calibrate simply with QuickCal Lightest all-in-one analyzer at only6.6 lb. (3.0 kg) Industry-leading 3 year warranty Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
Particle Analyzers
Teilch Particle Analyzers have proven significant advantages when compared to competitors’ solutions. Innovations in light source, flow control, analog and digital signal processing, components integration and software allow Teilch to provide a state of the art system for precision particle analysis.
-
product
Optical Noise Analyzer
A0040A
Optical Noise Analyzer is the industry first solution for evaluation of optical frequency noise of lasers as power spectrum density.
-
product
Laser Markers / 2D Code Readers
Panasonic Industrial Devices Sales Company of America
Panasonic Laser Markers are ideal for the high speed, non-contact, permanent labeling of metals, plastics, resins, glass and natural materials such as paper, wood or leather. Panasonic's Laser Markers make no contact with the target object and have no moving parts or consumables - a strong advantage over methods like stamping or engraving.
-
product
Paramagnetic Oxygen Purity Analyzer
Model 3010MA
Teledyne Analytical Instruments
Teledyne's Model 3010MA Paramagnetic Percent Oxygen Analyzer is a versatile, microprocessor-based instrument specifically designed for oxygen purity analysis. Drawing on the solid performance of Teledyne's 3000 Series control platform, the 3010MA provides the user with a wide variety of features while maintaining cost effectiveness.
-
product
Static Code Analyzer
HelixQAC
For over 30 years, Helix QAC has been the trusted static code analyzer for C and C++ programming languages. With its depth and accuracy of analysis, Helix QAC has been the preferred static code analyzer in tightly regulated and safety-critical industries that need to meet rigorous compliance requirements. Often, this involves verifying compliance with coding standards — such as MISRA and AUTOSAR — and functional safety standards, such as ISO 26262.
-
product
Beam Lead Capacitors
Beam lead capacitors have high insulation resistance, low dissipation factor, and low temperature coefficient, which allow for use in military and aerospace designs. Their robust performance and small form factor provide repeatable performance.
-
product
Universal PD & EMI analyzer
Spark P3
Doble Spark P3 is a universal partial discharge (PD) and electromagnetic interference (EMI) analyzer that uses a software defined radio signal detector to identify characteristics of insulation system deterioration that could lead to the failure of high voltage equipment. It detects signals from suitable sensors in a frequency range between 9 kHz to 2 GHz for PD and EMI, and DC to 500k Hz for acoustic and reference voltage measurements.
-
product
Chemiluminescence NH3 Analyzer
Model T201
Teledyne Advanced Pollution Instrumentation
The Model T201 combines a specially configured chemiluminescence analyzer with an external thermal converter (see "Features" tab for external converter photo) to give stable and repeatable NH3 measurements at very low levels. In addition, the T201 provides simultaneous values for NO, NO2, and NOx concentrations. The T201 is ideal for trace ammonia monitoring applications in ambient air as well as in clean rooms and make-up air units. Optional zero and span valves allow automatic, unattended calibration checks.
