Tube Testers
See Also: Neon
-
product
Wire Crimp Pull Tester (Motorized)
WT3-201M
The WT3-201M motorized wire crimp pull tester is designed to measure pull-off forces of up to 200 lbF [1 kN] for wire and tube terminations. The tester conforms to numerous UL, ISO, ASTM, SAE, MIL, and other requirements for destructive testing. Non-destructive testing is also possible, such as pulling to a load or maintaining a load for a specified period of time, as per the requirements of UL 486A/B. Programmable pass/fail limits with red and green indicators and audio alerts help identify non-conforming samples.
-
product
9VT Neon Tube Tester
West Coast Custom Designs, LLC
When the antenna and/or the Disc are touched to the tubing wall or electrode wires, the tester will cause the viable tubing to illuminate.
-
product
AA Neon Tube Tester
West Coast Custom Designs, LLC
When the antenna is touched to the tubing wall or electrode wires, the tester will cause the viable tubing to illuminate in a pulsating manor. This pulsing feature is fantastic for testing neon in bright sunlight as it is easier to see the light when flashing.
-
product
Portable Slimline Tube Tester
741200
Battery powered high-frequency generator for testing pumped neon tubes and fluorescent lamps, operates on 4 AA batteries. Tube being tested will illuminate in a pulsating manner if “good”. Includes leather case. 6-7/8” long x 1-1/2” wide x 3/4” deep. Batteries not included.
-
product
Tube Tester / Tube Checker
RM 1
The RM 1 is a Vacuum Tube Tester easy to handle, in its construction almost unique, which enables a fast, simple and precise plate current measurement (emission test) of the most common double triodes (6SL7-GT, 12AT7=ECC81, 12AU7=ECC82, 12AX7=ECC83)¹ and power pentodes (6CA7=EL34, KT66, KT88, 6550, 6L6-GC, 5881, 6V6-GT, 6BQ5=EL84)¹. The device has a distinct classic design, primarily consisting of a solid beech wood cabinet and a front panel of anodized aluminium. Because of its small dimensions it is easily transported and it doesn't need a lot of space for accommodation.
-
product
Gearbox Tester
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
product
Bit Error Rate Tester - MATRIQ
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
Automated Coherent Receiver Tester
CoRx Tester.
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
product
Open/Short Tester for Reverse Engineering Applications
Panther 2K-CT
Qmax Test Technologies Pvt. Ltd.
Panther 2K-CT is a versatile open\Short tester designed especially for reverse engineering application of tracing circuits of undocumented PCBA’s.Its innovative measurement technology helps tracing PCB tracks between components in a given circuit board. It can accommodate various types of clips\grabbers and connectors to access the device pins to trace the connectivity. Its user friendly software guides the user to place and move cluster of IC clips and probes to learn the connectivity and to generate netlist.
-
product
Bit Error Rate Tester - PXI
BERT 1001/1005 Series
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
Neon Tube Tester
- Convenient testing tool for trouble shooting.- "Torch" shape design with body-fitting leather mini-case, perfect for carrying.- Safe on button design with accidental turn-on protection;- Use only 4AA battery.
-
product
PAM4 Bit Error Rate Tester.
BERT-1102
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
product
Hoist Tester
The system has the capability of operating hyraulic powered hoists, DC powered hoists and 400Hz AC powered hoists. When a unit is connected to the system it is automatically detected and the system will load the unit's control software, acceptance procedures and operational safety limits. By doing all of this the operator does not need to worry about anything other than installing the unit and clicking Run to execute a full test procedure.
-
product
KVS Rugged Igniter Tester With Current Monitor
4314
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
product
MXE EMI Test Receiver, 3 Hz to 44 GHz
N9038B
The Keysight N9038B is a standards-compliant MXE EMI test receiver and diagnostic signal analyzer built on an upgradeable platform. You choose the frequency coverage you need to fully test devices with outstanding accuracy and sensitivity across required ranges.
-
-
product
Boiler Tube Oxide Scale Nondestructive Tester
DX-201'
This instrument is suitable for measuring non-magnetic stainless steel pipe inner layer accumulation rust. It can use a rechargeable battery, without power supply when test, which is suitable for outdoor environment operation. It can be used 4 hours once charge saturation. This product has been used by Hunan Xiangtan Power Generation Company Limited, Wuhan University, Nanyang Henan Yahekou Power Generation Co., Ltd., Anhui Huainan Pingwei power plants and Changsha thermal power plant, received good evaluations.
-
product
120 GBd High-performance BERT
M8050A
The Keysight M8050A high-performance bit error ratio tester (BERT) enables accurate characterization of receivers used in next-generation data center networks and server interfaces. With uncompromised signal integrity, support for NRZ, PAM4, PAM6, and PAM8 signals, and data rates up to 120 GBd, the flexible architecture of the M8050A supports 1.6T pathfinding as well as other leading-edge technologies.
-
product
64 Gbaud High-performance BERT
M8040A
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
product
Microwave Tubes
TRAVELING WAVE TUBES (TWTS), MAGNETRONS AND KLYSTRONS
Communications & Power Industries
CPI TMD has been immersed in the research, design and manufacture of electron devices since its inception, delivering solutions into some of the most demanding applications to support its customers’ requirements. CPI TMD's tube engineering "DNA" extends back to EMI Electronics' high-power klystron developments during World War II. Since then, CPI TMD has been instrumental in many of the industry's major TWT, magnetron and klystron developments.
-
product
Heated Tube
Shandong Drick Instruments Co., Ltd.
Specifications Length 100mm, capacity is less than 3ml, suitable for SGW-2, SGW-3, SGW-5 automatic polarimeter.
-
product
Traveling Wave Tube Amplifier
Skylink a leading provider in design and manufacture a wide range of traveling wave tube amplifiers(TWTAs) and microwave power modules(MPMs).Skylink's new generation of MPMs are based on a modular design, and use new technology, material and computer simulation system to improve weight, size and efficiency.Our main MPM series frequency covers range from 2 to 40GHz and providing more than 100W. They combine a helix TWT, a solid state amplifier and an integrated power conditioner in a compact package.
-
product
Tube MP
Applied Research and Technolgy
The world's most popular external microphone preamp - since 1995.
-
product
TWTs - Traveling Wave Tubes
Travelling wave tubes remains a valuable type of amplifier for high output power in the microwave range. Its main advantages are of high output power, big bandwidth-duration and reliability. Insight Product Co. offers TWT packaged tubes providing output power from tens to several hundred watt in a continuous mode and to 1.5-2.0 kw in a pulse mode, and frequency bandwidth of 1.5 octaves. TWT applications include satelite communications (transponders) both on land and on satelite installations, radio relay communication lines, electromagnetic compatability (EMC) testing industry for immunity testing of electronic devices, and radars (maritime, weather, airplanes, land).
-
product
Probes for Tube Inspection
Probes for tube inspection are lightweight but solidly constructed eddy current, remote field, magnetic flux leakage, and IRIS ultrasound. These probes are used for ferromagnetic or non-ferromagnetic tube inspection applications.
-
product
Thermowells, Protection Tubes And Heads
Choose from a variety of thermowells, protection tubes & industrial heads to protect your temperature probe from your process fluids or surrounding environment while also keeping your system sealed.
-
product
Commercial Grade Image Intensifier Tubes
ECHO Series
The commercial grade image intensifier tubes are used to amplify low light level images in a wide light spectrum for civil applications.Discover ECHO the high performance commercial image intensifier by Photonis. The ECHO technology is the commercial grade image intensififier tube by Photonis, offering two high performance grades to the commercial market for civilian users.ECHO image intensifier tubes serve many night vision applications for users that require good range and details at night andmaking them perfect for sport shooters, hunters, airsoft practioners and night vision enthusiasts.
-
product
Tube Mount Transmitter / DIN Rail Receiver
The 28670XX-DRX Series are unidirectional wireless systems that comprise a transmitter and a receiver.This Drexelbrook transmitter accommodates two digital signals in the range from 5 to 30 V AC/DC or 100 to 240 V AC and one analog current signal (4-20 mA). These signals are available for further processing at the receiver in the form of two relay contacts and one 4-20 mA current output. In addition, a third relay in the receiver diagnoses the status of the wireless connection (RF link).
-
product
Tube-To-Tube Gravity Handler
Rasco SO1000
The SO1000 test handler’s mature design and high reliability it provides excellent cost of test. Highly flexible as a result of a broad range of device kits can be combined with various Sensor and MEMS applications.Featuring a fast plunger with up to four plunger heads for high speed and high throughput with index time down to 500 ms. Available in single, dual, and quad configurations.
