Tube Testers
See Also: Neon
-
Product
Neon Tube Tester
-
- Convenient testing tool for trouble shooting.- "Torch" shape design with body-fitting leather mini-case, perfect for carrying.- Safe on button design with accidental turn-on protection;- Use only 4AA battery.
-
Product
9VT Neon Tube Tester
-
West Coast Custom Designs, LLC
When the antenna and/or the Disc are touched to the tubing wall or electrode wires, the tester will cause the viable tubing to illuminate.
-
Product
AA Neon Tube Tester
-
West Coast Custom Designs, LLC
When the antenna is touched to the tubing wall or electrode wires, the tester will cause the viable tubing to illuminate in a pulsating manor. This pulsing feature is fantastic for testing neon in bright sunlight as it is easier to see the light when flashing.
-
Product
Bit Error Rate Tester - MATRIQ
Tester
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
Product
Hoist Tester
Tester
The system has the capability of operating hyraulic powered hoists, DC powered hoists and 400Hz AC powered hoists. When a unit is connected to the system it is automatically detected and the system will load the unit's control software, acceptance procedures and operational safety limits. By doing all of this the operator does not need to worry about anything other than installing the unit and clicking Run to execute a full test procedure.
-
Product
Bit Error Rate Tester - PXI
BERT 1001/1005 Series
Tester
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
Product
Gearbox Tester
Tester
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
Product
Wire Crimp Pull Tester (Motorized)
WT3-201M
-
The WT3-201M motorized wire crimp pull tester is designed to measure pull-off forces of up to 200 lbF [1 kN] for wire and tube terminations. The tester conforms to numerous UL, ISO, ASTM, SAE, MIL, and other requirements for destructive testing. Non-destructive testing is also possible, such as pulling to a load or maintaining a load for a specified period of time, as per the requirements of UL 486A/B. Programmable pass/fail limits with red and green indicators and audio alerts help identify non-conforming samples.
-
Product
MTM-Bus Tester
PXIe-1149.5
BUS Tester
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
Product
PAM4 Bit Error Rate Tester.
BERT-1102
Tester
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
Product
Automated Coherent Receiver Tester
CoRx Tester.
Receiver Tester
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
Product
Portable Slimline Tube Tester
741200
-
Battery powered high-frequency generator for testing pumped neon tubes and fluorescent lamps, operates on 4 AA batteries. Tube being tested will illuminate in a pulsating manner if “good”. Includes leather case. 6-7/8” long x 1-1/2” wide x 3/4” deep. Batteries not included.
-
Product
KVS Rugged Igniter Tester With Current Monitor
4314
Tester
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
Product
AXIe M8000 Series of BER Testers
Bit Error Rate Tester (BERT)
Simplified time-efficient testing is essential when you are developing next-generation computer, consumer, or communication devices. The Keysight M8000 Series is the highly integrated BER test solution for physical layer characterization, validation, and compliance testing. With support for a wide range of data rates and standards, the M8000 Series provides accurate, reliable results that accelerate your insight into the performance margins of high-speed digital devices.
-
Product
120 GBd High-performance BERT
M8050A
Bit Error Rate Tester (BERT)
The Keysight M8050A high-performance bit error ratio tester (BERT) enables accurate characterization of receivers used in next-generation data center networks and server interfaces. With uncompromised signal integrity, support for NRZ, PAM4, PAM6, and PAM8 signals, and data rates up to 120 GBd, the flexible architecture of the M8050A supports 1.6T pathfinding as well as other leading-edge technologies.
-
Product
Universal A/V Tester
Tester
This tester was built for our client with the specific requirement that specific UUTs can be added to the system by our client. We handled developing test software for the first 2 UUTs utilizing an open programming structure that allowed programming modules to be strung together to create test programs for any additional UUT that our client wants to add in the future.
-
Product
Error Detector Remote Head 32 and 17 Gb/s
N4952A
Bit Error Rate Tester (BERT)
The N4952A is an affordable and compact error detector remote head available in 4 to 17 Gb/s and 5 to 32 Gb/s configurations. Compatible with the N4960A Serial BERT controller, it is the perfect solution to test up to 32 Gb/s per channel for 100 Gigabit Ethernet applications and other high-data rate devices. The N4952A error detector supports PRBS or user patterns and operates up to 32 Gb/s in a single band with no gaps or missing data rates. The remote head allows the test equipment to be located very close to the device under test, eliminating the need for long cables that degrade signal quality.
-
Product
Medical Needle Tubing Toughness Tester RX-01
-
The Medical Needle Tubing Toughness Tester is suitable for measuring the toughness of stainless-steel needle tubing, such as injection needles, prefilled syringe needles, and IV (infusion) needles.Product Features Supports testing of various needle wall specifications: normal wall, thin wall, and ultra-thin wall. 7-inch color touchscreen with graphical user interface (GUI) Users can freely select the bending angle and number of test cycles. This instrument features automatic data storage and retains memory even after power-off. This instrument is equipped with multiple safety features to prevent accidents caused by improper operation during testing, including an emergency stop button and overload protection. Equipped with a micro-printer and automatically prints test results upon completion Standard USB interface for convenient data transfer This instrument features multi-level user permissions, compliant with GMP standards. ISP online control and upgrade capabilities enable remote modification of test functions as needed.Test PrincipleSecure one end of the needle stainless-steel tubing and apply a force over a specified span. First, bend it in one direction, then bend it to a specified angle in the opposite direction, and repeat this bending cycle a specified number of times.Test StandardsThis test instrument conforms to many national and international standards:ISO 9626:2016 - Stainless steel needle tubing for the manufacture of medical devicesGB 15811-2025 - Sterile hypodermic needles for single useGB/T 18457-2024 - Stainless steel needle tubing for the manufacture of medical devices
-
Product
MXE EMI Test Receiver, 3 Hz to 44 GHz
N9038B
Receiver Tester
The Keysight N9038B is a standards-compliant MXE EMI test receiver and diagnostic signal analyzer built on an upgradeable platform. You choose the frequency coverage you need to fully test devices with outstanding accuracy and sensitivity across required ranges.
-
Product
Medical Needle Tubing Stiffness Tester GX-01
-
The Medical Needle Tubing Stiffness Tester is designed to measure the stiffness and rigidity of stainless-steel needle tubing, such as injection needles, prefilled syringe needles, and IV (infusion) needles.Test PrincipleThe instrument applies a prescribed bending force to the stainless-steel needle sample, and the high‑precision sensor of the rigidity tester measures and records the rigidity of the needle tube at the point of application. Product Features Supports testing of various needle wall specifications: regular wall, thin wall, extra-thin wall, and ultra-thin wall. 7-inch color touchscreen with graphical user interface (GUI) This instrument features automatic data storage and retains memory even after power-off. This instrument is equipped with multiple safety features to prevent accidents caused by improper operation during testing, including an emergency stop button and overload protection. Equipped with a micro-printer and automatically prints test results upon completion Standard USB interface for convenient data transfer This instrument features multi-level user permissions, compliant with GMP standards. ISP online control and upgrade capabilities enable remote modification of test functions as needed.
-
Product
Protection Heads And Tubes
-
Choose from a wide variety of industrial protection heads and tubes to protect your temperature sensor probe from your rugged process application or surrounding environmental conditions.
-
Product
Probes for Tube Inspection
-
Probes for tube inspection are lightweight but solidly constructed eddy current, remote field, magnetic flux leakage, and IRIS ultrasound. These probes are used for ferromagnetic or non-ferromagnetic tube inspection applications.
-
Product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
BUS Tester
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
Product
Power Tube Burn-in Station
Maxi-Burn
-
The MaxiBurn Tube Preheater is a 2U rack mountable or bench top unit for heating 30 Octal Base Tubes. Designed for continuous use heating standard power pentodes to normalize their characteristics before testing or matching the MaxiBurn powers the tube filaments and drives a nominal plate current through each tube. Normal function of each tube is indicated by a glowing LED associated with the tube.
-
Product
Flow Tube
913
-
The Meech Model 913 Flow Tube is designed to neutralise static charges on materials in handling and conveying systems. It incorporates in-line ionisation, which eliminates material clinging and clogging in ducting systems due to static charges.
-
Product
Photomultiplier Tube (PMT) Bases
-
Scintillation detectors produce light as they absorb energy, and these light flashes result in the release of a proportionate number of photoelectrons at the cathode of a photomultiplier tube (PMT). Each of the ORTEC Photomultiplier Tube Bases is designed to accommodate a particular type of PMT to distribute the operating voltages to all its elements, and to derive signals from it.
-
Product
Averaging Pilot Tubes
-
Meriam manufactures the widest range of Averaging Pitot Tubes for gases, liquids and steam with bi-directional flow capability. Under the Accutube brand name, there are four standard models; Inline, Insertion, Flanged and Wet Tap which can provide a flow solution for your toughest applications. To provide the complete flow solution that meets your specific needs, we can provide DP or Multivariable transmitters from the brand of your choice, or we will recommend the best fit for your application. These transmitters can be installed on the Accutube and configured to your specific flow requirements here at Meriam by qualified technicians, reducing your expense and time .
-
Product
Pitot Tubes
-
The dpm-i Pitot Tube is a new design concept in Pitot Static Tube technology. It is a multi-functional sensor. It can replace thermally heated instruments, where power requirements are high. Gives easy access to duct measurement compared to a standard Pitot Tube. For example, in ceilings voids and confined areas, where there is a thick lagging or metal cladding.
-
Product
Metal Tube Float Flow meter
F56
-
Beijing Airport Beiguang Instruments Co., Ltd
F56 Metal Tube Float Flow meter Series are used for measure instantaneous and accumulated flow rate of liquid, gas and steam in closed pipelines. It is suitable for metering flow value on site or electronic remote. The measuring principle is based on the hydrodynamic effects,This makes float moving from bottom to top in vertical Pipe. As the displacement of float is in related to flow rate, which can be read from the indicator by means of the magnetic drive system in non-contact form . Also, flowmeters output electrical signal (4-20)mA / hart communication protocol with high / low limit Warning switches/integrating flow PCB broad can be configured.
-
Product
Phantom Vent Tube Metal Detector
-
The Phantom Vent Tube metal detector is primarily designed to detect and track a fallen vent tube nozzle inside a bottle that is conveyed through bottle-processing equipment. The convenient retrofit design allows for easy installation into existing bottling lines. Built from stainless steel (304) material and totally enclosed for washdown purposes, the detector phases out the conveyor belt and maintains a steady sensitivity.
