Mechanical Test
material and physical properties.
-
Product
MECHANICAL TEST FIXTURE KITS
TX-MT-SERIES
-
Test-X MT Series mechanical kits are an affordable solution to printed circuit board testing. With multiple configurations and available options, this product is sure to meet your testing needs. The MT Series features a hinged 3/8" FR4 probe plate, tooling holes for accurate drilling, and side handles for easy transportation.
-
Product
Rock Mechanics Testing Equipment
-
Rock mechanics is the part of geotechnical engineering that studies the behaviour of rocks under variable physical and environmental conditions. Testing is undertaken to enable the prevention of geotechnical failure such as shearing, by measuring the behaviour of rocks for compliance with regulations, design specifications and quality control standards.
-
Product
System for Analyzing Door Handles
-
In the production process of a vehicle door handle, the electrical functions of the component are to be tested. The mechanical testing of the operation of the door handle is performed by a PLC-controlled test system. In addition to the mechanical test, the electrical parameters: “serial data stream” and “impedance of the antenna” are to be analysed.
-
Product
Environmental Testing
-
Environmental testing capabilities include: High and Low Temperature Testing including Thermal Shock. Humidity Testing to 100% Relative Humidity at High and Low Temperatures. Altitude Testing to 100,000 Feet. Combined Vibration, Temperature and Altitude Testing. Mass Spectrometer for Leak Testing. Vibration Testing to 50 G's and 3000 Hz including Resonance Scan, Cycling, and Endurance. Free Fall Half Sine Wave Mechanical Shock Testing to 100 G's
-
Product
Analytical Techniques
-
Anderson Materials Evaluation, Inc.
Our numerous analytical techniques, we tackle a wide range of materials challenges and commonly combines several analytical techniques to fully address complex and multi-dimensional materials issues. Our materials analysis laboratory provides XPS surface analysis, thermal analysis (TGA, DSC, TMA), FTIR infrared spectroscopy, UV-Vis spectrophotometry and reflectivity measurements, gas chromatography – mass spectroscopy (GC-MS), SEM/EDX, optical microscopy, mechanical testing, electrochemistry and corrosion analyses, residual gas mass spectroscopy, contact angle measurements, surface contamination measurements, adhesive bonding failure analysis, facility testing for silicone contamination, mechanical testing, metallography and fractography, density and porosity measurements, volatile organic component testing, friction, and other analytical capabilities. We continue to upgrade and expand our arsenal of analytical techniques and custom analytical methods to support our customers’ needs.
-
Product
Tumbling Barrel Test Apparatus
-
SCR Elektroniks make Tumbling Barrel Apparatus is specially designed and manufactured for use in laboratories involved in testing Appliances, Electrical Accessories, Luminaries and other related Electro technical products. It is used to perform the test specified in many standards to determine compliance with safety requirements, particularly mechanical strength of test samples. SCR Elektroniks Makes Counter to count ON/OFF of Limit switch.
-
Product
Counterfeit Analysis / Screening Services
-
DPACI perform counterfeit part analysis on all types of electrical, electronic, and electromechanical (EEE) components. Our suspect counterfeit analysis task groups include source identification, manufacturer validation, external visual inspection, mechanical inspection, electrical test, X-Ray, in-depth internal visual and materials analysis. With one of the largest databases of test reports for EEE components, we can offer similar historical data for correlation with images, test data, certifications and reports.
-
Product
ElectroForce Mechanical Test Instruments
-
We start with your specific testing needs and combine unique ElectroForce motor technologies with our test applications engineering expertise to create a tailored test solution that meets your testing objectives. After you buy a TA Electroforce product, you become a valued, lifelong customer. Providing exceptional, ongoing support is our commitment to you.
-
Product
Optomechatronics Testers
-
T100 is a flying actuator tester designed to calibrate and test any kind of device, module or product with electronic, optical and mechanical functions, using the latest opto, MEMS, sensor, microelectronics, micromechanics technologies.T100 can be equipped with tools and actuators to perform calibration, electrical test, mechanical test, optical test.All on a single machine without any need for additional equipment.It is the ideal tester for production lines with a wide variety of products and frequent entry of new ones.
-
Product
3-Axis Non-Robotic Automated Testing System
AT3
-
The Instron AT3 is a space-efficient, highly adaptable 3-axis mechanical testing platform designed for automated execution of tensile, compression, flexural, and lap shear tests. Built to comply with a broad spectrum of ASTM and ISO standards, it’s well-suited for evaluating materials such as plastics, elastomers, thin films, foils, and metals. The system streamlines the entire testing workflow from specimen measurement and handling to strain measurement and specimen disposal—enabling users to load up to 160 samples and let the AT3 take care of the rest. Boost productivity, reduce manual intervention, and achieve consistent, dependable results with every test cycle.
-
Product
Electrical Button Life Span Tester
IEC60884
-
Shenzhen Autostrong Instrument Co., Ltd.
Plugs and the sockets life tester is designed according to the corresponding provisions of the GB2099-96,GB16915-97 and IEC60884-1,used to detect the mechanical life test of the household and similar purposes of the plugs and the sockets products.
-
Product
Insulation Meters
-
Here you will find an insulation tester for a variety of ranges between 50 mega ohms and 2000 mega ohms. The portable manual insulation tester is used for determining insulation resistance, continuous current, alternating current and testing. With an insulation tester, measurements can be taken for different voltages, beginning with 100V up to 10,000V. Measurements meet the DIN VDE 0413 part 1 standard. The insulation tester comes with a test mechanism, clips, batteries and a carrying case. The insulation meter can be equipped for test laboratories if an optional DIN EN ISO is acquired.Measurement of insulation in cables and motor coils is vitally important for the prevention of accidents and damage to installations and is obligatory according to most codes of conduct.
-
Product
Tumbling Barrel Apparatus
ME-999
-
Is specially designed and manufactured for use in laboratories involved in testing Appliances, Electrical Accessories, Luminaires and other related Electrotechnical products. It is used to perform the test specified in many standards to determine compliance with safety equirements, particularly mechanical strength of test samples.
-
Product
Mechanical Fixtures Available w/ESD Plates & ESD Pressure Pins
-
H+W Test Products has developed a series of inexpensive mechanical test fixtures. These fixtures are designed for testing low volume runs of printed circuit boards or prototype applications requiring approximately 150 test points.
-
Product
IEC60950 Ball Drop Impact Test Apparatus
-
Shenzhen Chuangxin Instruments Co., Ltd.
It is mainly used for mechanical strength testing equipment enclosure, test equipment enclosure should be able to ensure that the structure can be expected to withstand the operation does not produce within the provisions of the standard risk for damage to the outer surface of the enclosure will touch dangerous parts of the apparatus.
-
Product
Universal Testing Systems (Up To 300 KN)
6800 Series
-
Instron’s 6800 Series universal testing systems deliver high-performance mechanical testing up to 300 kN. Designed for precision and durability, these systems offer exceptional measurement accuracy (±0.5% down to 1/1000th of load cell capacity) and fast data acquisition rates up to 5 kHz. Ideal for tensile, compression, flexure, torsion, peel, lap shear, and many other test types, the 6800 Series provides the flexibility and control needed to handle everything from delicate specimens to high-strength materials, making it a trusted solution for demanding testing environments.
-
Product
Universal Test System
LS6601A
-
LS6601A Universal Test System is based on LXI bus, primarily used for functional electronic product or system verification, test parameters. Because the system design is based on LXI bus structure, so its addition to general characteristics of versatility, scalability, but the architecture of the system more flexible, the test system is not limited to one or more cabinets, but may be needed test network and multiple LS6601A and can be easily grouped into one or more of the ground test system, depending on the test mechanism, form a powerful set of test, control, simulation, simulation, data management as one; distributed in different places .
-
Product
WinTest® Software
-
WinTest® is a high-performance software package that is used to operate all TA ElectroForce mechanical test instruments. With both a flexible interface and a powerful instrument controller, WinTest allows users to choose what data they monitor in real-time while accurately recording all the necessary data for their tests.A single user interface to define acquisition settings, adjust control parameters even while a test is running, and monitor a test in real-time provides a powerful solution to your testing needs.
-
Product
Digital Indicators
-
The precise measuring of dimensions is important for so many enterprises: engineering, surveying, construction, machine tooling and auto manufacturing, just to name a few. And electronic digital indicators provide people in these fields with the means to accurately measure the dimensions of objects both very small and very large by translating small linear distances into rotational movement. Precision measuring tools like electronic digital indicators can also be used to measure distance and range. If your job requires mechanical testing or machining, you may want to shop our selection of dial indicators.
-
Product
Mechanical Test Head Housing
-
a result of more than 10 years' experienceavailable with integrated manipulatorfully integrated docking and board lockingtest housing mechanics design as per customer specificationssuitable for individual and high-volume productionstandard and customized dimensionsno limitation in size and electrical power capacitiesquick and easy locking and unlocking process for board changelarge application space load boardoptional number of channel boards as per customer specificationsfamily/DUT board connection achieved by high-end double-ended spring probes - 50 Ohmhigh-end cooling fansfacilitated adaptation with all available manipulator solutionsdocking design in compliance with customer internal docking standards/dimensionsdocking force as per customer specificationscenter of gravity fully compensated
-
Product
Axle Damping Test Bench
C_MSD C 13.0 W220 | VP 215050
-
Maschinenbau Haldenwang GmbH & Co. KG.
The axle damping test bench C_MSD is characterised by a fast and precise mechanical testing of the axle damping. Through the frequency-controlled plate activation via electric motors, the maximum vibration amplitude is calculated and then the axle damping is evaluated according to the Lehr damping principle. The fully automatic test sequence, including the calculation of axle and vehicle weight, saves time and allows a reliable assessment of the axle damping.
-
Product
Dynamic and Satatic Electro-Hydraulic Servo Testing Machine
PLS Series
-
Jinan Testing Equipment IE Corporation
PLS series dynamic and static testing machine is produced according to the dynamic servo test technology. Our design of the electro--hydraulic servo testing system is unitized, standardized and modularized, which enhance the stability and reliability of the system. The electro-hydraulic servo testing system is mainly used to test the dynamic and static mechanical performance of material parts. Equipped with corresponding accessories, the servo-hydraulic testing system can do tensile, compression, low and high cycles, crack growth tests and other mechanical tests for various kinds of materials. The Dynamic and Static Testing Machine is widely used in the fields of aviation and aerospace, ship-building and military industries.
-
Product
Mechanical Load Tester
-
Solar modules and collectors, whether on roofs, in façades, or freestanding, are often exposed to high mechanical stress or load: A deep layer of snow or strong winds can greatly affect the materials and connections. Mechanical load test stands accurately test the durability of PV modules and thermal solar collectors.
-
Product
MECHANICAL TEST FIXTURE KITS
TX-MT-100 SERES
-
Test-X MT-100 Series mechanical kits are an inexpensive solution for testing smaller printed circuit boards and other devices.The MT-100 Series features a 1/2" thick FR4 probe plate and a 3/8" thick Lexan top plate. Precision alignment is assured through tooling holes in both the probe and top plates. Units are available with a 2-1/2" pan or an upper head assembly
-
Product
High-Precision Material Testing Machine Vexus
MT5 Series
-
Sinowon Innovation Metrology Manufacture Ltd.
Vexus MT5 series of material testing machine is designed in single column with maximum testing force 5KN, it is able to make the material testing about tensile, compression, bending, shearing, bonding strength, peeling, tearing, etc, it is applied to test the material such as rubber, plastic, leather, metal, nylon line, fabric, paper, aviation, packaging, construction, petrifaction, electrician, vehicle and other materials. It is a stable and affordable material testing instruments for the incoming quality control, physical test, mechanics research, material research, etc.
-
Product
CAM/TRAC Test Kits
Series 431
-
Series 431 GR2270 ‘Z’ Axis Camtrac Dual Well Mechanical Test Kits.
-
Product
High Speed Test Bench
AT444
-
AC motor with mechanical multiplying gearbox test benches allow precise programming of all drive parameters required for accurate rotating devices test.The use of special high-speed bearings, mechanical components and parts wear resistant leads to a large life. The supply includes the electronic drive and control as well as the entire oil cooling unit.
-
Product
Instron Materials Testing Software
-
Instron offers a comprehensive suite of materials testing software solutions designed to support a wide range of mechanical testing applications, from static tensile and compression to fatigue, impact, and melt flow. Built for precision and efficiency, these software packages provide powerful tools for test control, data analysis, and reporting, with support for industry standards such as ASTM, ISO, and EN. Whether for basic quality control or advanced research, Instron’s software solutions deliver flexible, user-friendly interfaces and robust data integrity features to meet the diverse needs of modern testing laboratories.
-
Product
Nanomechanical Test System
Hysitron TI Premier
-
Bruker’s Hysitron TI Premier nanoindenter was specifically designed to deliver industry-leading, quantitative nanomechanical characterization within a compact platform. Built upon proven Hysitron technology, the TI Premier provides a broad suite of nanoscale mechanical and tribological testing techniques.
-
Product
Mechanical Testing
-
The Mechanical Testing Department at IMR is well equipped to perform most standard mechanical testing, as well as specialized tests designed to the customer's requirements. A complete in-house machine shop supports the department with precise specimen preparation and fixture fabrication.
