Static Electric Field
is a stationary charge that is time invariant.
-
Product
Field Strength Meter
FIM-71 VHF
-
The Model FIM-71 is a portable, laboratory quality Field Strength Meter designed for rigorous field applications. Combining a calibrated half-wave dipole antenna and a highly accurate tuned voltmeter with a range of 140 dB, the FIM-71 is suitable for practically all types of RF emission measurements in the 45 MHz to 225 MHz spectrum. The operator can switch select wide or narrow bandwidth, peak or average value of TV or pulse modulated signals, AM or FM demodulation, and a meter dynamic range of either 20 dB or 60 dB. A dc analog output voltage, proportional to the meter indication, is provided for driving a chart recorder. A leveled output from the calibrating oscillator is available for measuring cable insertion loss, filter response, amplifier gain, and other signal ratio measurements. The 4-1/2 inch, taut band, mirrored scale meter is calibrated in volts and dB for precise measurements in field or laboratory environments.
-
Product
Single Axis AC Magnetic Field Sensor
MGCH-2
-
Macintyre Electronic Design Associa
The MGCH-2 is the lowest noise, highest sensitivity single axis AC magnetic field sensor available for the measurement of sub radio frequency fields. Because of its innovative design, the MGCH-2 amplitude response is insensitive to the frequency of the field over its 10 Hz to 100 kHz frequency band. Accuracy at 10 kHz is 0.1 dB, and the amplitude response stays within 2 dB peak-to-peak over the bandwidth.
-
Product
Static Honest Meter
-
Sataton Instruments Technology CO., Ltd
Static honest meter is professional designed to determine the attenuation of static electricity, corona discharge time, static voltage attenuation half-life, static decay curve and other electric property of fiber, yarn, fabric, textile or plate materials. It is suitable for measuring the diffusibility of static in the testing samples.
-
Product
33/60 GHz Dual Electrical Channel Module
N1040A
-
The N1040A is a dual electrical channel plug-in module for the N1000A DCA-X mainframe and provides two electrical channels with maximum bandwidth of 33 or 60 GHz, based on the option selected.
-
Product
Phase Angle and Power Factor Transducer of Single-phase AC Electric Power
NMTFi
-
The NMTFi device is a phase angle and power factor transducer operated in single-phase power network and featuring two independent analogous outputs. The A output measures the phase angle between voltage and current, the B output measures the power factor. In such a was one single NMFTi transducer is able to replace two customary transducers thus making it possible to achieve significant savings in installation space.
-
Product
Field Meter
AP01 FULL HD
-
The AP01 FULL-HD is a field meter with full coverage of the terrestrial TV bands, cable TV (CATV), 1st IF satellite and, if the relative option is inserted, the return channel 5-65 MHz.
-
Product
Electric Vehicle Battery Tester
-
The Electric Vehicle Battery Tester (EVT) is designed for testing traction batteries in electric vehicles or HEV batteries in hybrid electric vehicles. The EVT realizes the functions charge and discharge with freely programmable set values for current, voltage, power or resistance in test programs, as well as the registration of the corresponding measured data.
-
Product
3.2Gbps Optical & Electrical Bit-Error-Rate Tester
OPB3200
-
The OPTELLENT OptoBERT™ OPB3200 is a cost-effective easy-to-use bit-error-ratio (BER) measurement system for testing components and systems in R&D and manufacturing environments as well as field installations.
-
Product
IEC60335 Standard Electrical Temperature Tester
CX-w15
-
Shenzhen Chuangxin Instruments Co., Ltd.
Standard Test corner/room conform to IEC60335-1:2004. and GB4706.1-2005. can be used to the temperaturetest of all kinds of electronic products supply, in conformity with the standards requirement of the environmental conditions.
-
Product
Electricity Metering Device- Residential
Mk31E
-
Mk31E is another addition to the Papillon series which enhanced the Mk31 with a disconnect relay, additional communication capabilities, advance tampering features and a larger memory storage capacity.
-
Product
Tester Electrical Interfaces
-
The primary element of the tester electrical interface is the Probe Pin Ring (PPR). Sometimes referred to as a ‘tower,’ this array of spring-loaded probes can be arranged to provide a controlled impedance path, a low leakage connection, a low inductance arrangement for high currents, or just about any connection characteristic you require. inTEST EMS provides electrical interfaces in various OEM-supported designs, inTEST standards, and custom configurations.
-
Product
11 Gbps Optical & Electrical Bit-Error-Rate Tester
OptoBERT™ OPB-X110
-
The OPTELLENT OptoBERT™ OPBX110 is a cost-effective easy-to-use 10G optical and electrical bit-error-ratio tester (BERT) for testing components and systems in R&D and manufacturing environments as well as field installations.
-
Product
Magnetic Field Cancelling System
MK-1
-
Single axis magnetic field cancelling system for MRI scanners and biomagnetic applications. This system is used when the magnetic field sensor cannot be placed within the shielded volume. For example, in MRI applications the sensor is usually installed outside of the shielding room because of the MRI scanner's high fringe field.
-
Product
Vehicle Electromagnetic Field Exposure Test System
SEM-400
-
Beijing KeHuan Century EMC Technology Co,.LTD
Vehicles are our daily public transportation. Electromagnetic pollution in vehicles has attracted more and more public attention. The newly revised compulsory standard GB27630-201X "Passenger Car Air Quality Evaluation Standard" intends to require the electromagnetic field in the car as one of the indicators, according to GB/T37130-2018 "Measurement method of vehicle electromagnetic field relative to human exposure" The measurement method is to measure the intensity of the magnetic field in the car. In the frequency range of 10Hz-400kHz, the electromagnetic field measurement result should meet the public limit requirements of GB8702-2014 for electromagnetic exposure.
-
Product
Electric Servo Motor Type 1 Axis Vibration Tester
-
In Addition, The System Configuration Requires At Least 3 Main Units, A Control Panel, And A Controller, And Does Not Require Hydraulic Units Or Blowers. The Exciter Can Perform Standard Tests And Performance Tests Required For Automobile Seats Based On An Electric Servomotor Type Multi-Axis Vibration Tester.
-
-
Product
Field Probe Positioner
-
The Field Probe Positioner FSM2315 is designed for the automation of the 16 point measurement, according to IEC/EN 61000-4-3. The system provides X and Y axis positions for continuous and step by step movement for the filed probe, 0.8m above the floor and with a 1.5m x 1.5m area, for the 16 sensor positions. A dismountable solution is available.
-
Product
Field Comm Analyzer
S5800H
-
S5800H Series Field Comm Analyzer is an 8.4 inch large touch screen instrument which is designed specifically for wireless communications field engineers and technicians. S5800H series provide all necessary measurement functions and performance to accurately characterize the signal environment in addition to clearing, detecting, identifying and locating signal interferenc.
-
Product
Electricity Meter Test Equipment
ELMA
-
The Electricity Meter Test Equipment ELMA due to modular concept enables to tailor specifications to specific laboratory demand. The available power and the maximum current of 240 A of extremely pure synthesized 4-quadrant test signal covers the needs of both precision and high capacity testing laboratories.
-
Product
Electric Testing
-
Our Capabilities*Dielectric Withstand*Hi-Potential Testing*Voltage Drop*Contact Resistance*Gate Leakage*Insulation Integrity*Dielectric Integrity
-
Product
Single Phase Multi-rate Static kWh Meter
SY 1035
-
Hong Kong Songyang Industrial Ltd.
Adopt ADE7755 measurement chip. High accuracy class. Large overload times. Can sum up the absolute value of positive and negative energy. Record power energy of this month, last month, and the month before last.
-
Product
Electric Vehicle Charging Station EVSE Test Adapter
FEV100
-
Test the safety and performance of a type 1, level 1 or level 2 electric vehicle ac charging stations (EVSEs) with the Fluke FEV100. This test adapter simulates the presence of an electrical vehicle, allowing you to conduct tests in combination with appropriate test instruments such as a digital multimeter or oscilloscope.
-
Product
Electrical Tester
C.A 755
-
Lightweight and comfortable to handle, the C.A 755 is equipped with an IP 54 casing protected against dust and capable of withstanding falls from 2 metres. With its large 3,000-count backlit display, the C.A 755 tester is ergonomic and functional.
-
Product
Electrical Calibration
-
Multifunction and special calibrators for electrical laboratories. All Meatest calibrators support computer assisted automated calibration to save your time.
-
Product
Electrical Tester
T+Pro
-
Safer than solenoid testers and fully compliant with NFPA 70E, (when used properly per Article 110.4 Use of Equipment (A) Test Instruments and Equipment), the T+Pro helps electricians and technicians work safer by indicating the presence of voltage, even when the batteries are dead.
-
Product
Electrical Safety Analyzers
-
Fluke Biomedical electrical safety analyzers provide accurate and reliable results, helping you meet your medical device testing and quality requirements while ensuring patient safety.
-
Product
Magnetic Field Visualization
mageye
-
Our mobile "magnetic field sensor" allows you to visualize and evaluate magnetic stray fields. Our mageye, matesy’s miniaturized magneto-optical USB microscope, provides information about the magnetic fields on the surface of a wide variety of samples with resolutions in the micrometer range.
-
-
Product
Electrical Test & Measurement Products
-
Electrical Test & Measuring Products, Including Clamp Meters, Voltage Testers, Multimeters & Test Kits
-
Product
Portable Electricity Meter Testers
EE-120A-1S
-
The EE-120A-1S unit consists of a single-phase energy standard class 0.1 and current load up to 120A. The unit performs testing of all types single-phase electricity meters using the voltage of the site. The meter error can be measured for active, reactive or apparent energy, in Manual Mode or with predefined Test Plans using the keyboard and the LCD display on the panel. Register Test, Starting Current Test and No Load Test can be performed too. The energy standard of the system can be used without the phantom load to test meters with customer load and perform analysis of the site – with direct measurement or with optional current clamps.
