Electrical Testers
-
product
Brushless Electric Torque Screwdrivers
VB-Series
The HIOS VB-Series brushless electric screwdriver is designed to plug directly into a power outlet and does not require a separate power supply unit. Features a high performance brushless motor design provides durability and reduces the standard maintenance costs for electric screwdrivers. Operates on a duty cycle of 0.5 seconds on and 3.5 seconds off.
-
product
Portable Electrical Management Systems
EMS-LCHW30
Progressive Industries Portable Electrical Management Systems (EMS) provide full RV protection against all adverse power conditions. You will feel secure with multi-mode surge, voltage, polarity and lost/open neutral protection. Each unit includes a digital display, scrolling continuously through the power source information: Voltage(s), current, frequency, error code, and previous error code (if applicable). Replacement parts are simply plug-and-play, making repairs quick and easy. As with our portable models, the computer is driven by state of the art microprocessors. Should the software ever change, EMS owners can receive a free upgrade at no cost.
-
product
Surface Roughness Tester Profilometer
TIME®3231
Beijing TIME High Technology Ltd.
TIME® 323X series is advanced high-end surface roughness measuring instruments with wide testing range (±400µm) and high accuracy (tolerance±5%, repeatability 3%). Meanwhile, TIME® 323X surface roughness tester features with skidless/skid measurement, which means it can reach smaller and harder to reach parts than other conventional tools. Up to 55 paramenters for roughness, waviness and primary profile are supported. Apart from those features mentioned above, TIME®3231 is loaded with 90° measurement function.
-
product
Network Tester
PeakTech Prüf- und Messtechnik GmbH
Compact 3½-digit multimeter, developed according to the CAT III 600 V standard with integrated LAN network tester. In addition to the extensive measurement functions for voltage, current and resistance, this model has a fast-reacting continuity test with an acoustic signal and the possibility of performing diode tests. This combination measuring device is a very practical test device that easily shows the correct pin assignment of network cables by comparing a transmitter with the corresponding cable receiver using an LED. Trouble-free checking of cable passage, open, short and cross connect is possible.
-
product
LAN Packet Tester
LE-590TX
The LE-590TX is a LAN analyzer that connects to a PC's USB2.0 port. In TAP mode, you can capture full duplex data on 10/ 100Base-TX and transmit to the PC at 480Mbps via the USB2.0 interface. In PG mode, you can generate test packets at up to 100Mbps line rate.
-
product
Hardness Tester
JINAN PRCISION TESTING EQUIPMENT CO., LTD
Hardness testing is measuring a material's resistance to permanent deformation at its surface
-
product
Air Data Tester
PS131b
Aircraft Development Industries cc
The Model PS131b is identical to the PS131bII except that it is housed in a 19 inch U2 rack mount enclosure. This is suitable for equipment racks in a workshop environment. Like the PS131bII it is an advanced Air Data - Pitot Static Tester, which is a completely digital, microprocessor-controlled device using all solid state transducers and components.
-
product
ICI Pilling Box Tester
UI-TX05
ICI Pilling Box Tester is used to assess fabric surface pilling and fuzzing by tumbling randomly. This pilling test machine is also called as ICI pilling and snagging tester/ICI pilling box. ICI pilling box test method includes ISO 12945.1, BS 5811, GB/T 4802.3, JIS L1076, etc.
-
product
Socket Tester c/w Buzzer
DL1090
Clear visual and audible indication of wiring status LED indication of a wide range of wiring conditions Designed to EN 61010 and IP30
-
product
De-Energized Tester
MOTOR GENIE
The MOTOR GENIE® can see more than a megohmmeter, resistance tester, or RCL tester, making it the perfect tool for troubleshooting, startup, and quality control of low voltage AC induction motors.
-
product
Portable Hardness Tester
Beijing TIME High Technology Ltd.
A compact, handheld device used for on-site measurement of a material's hardness.
-
product
Rope Testers
The LMA Signal measures loss of metallic cross-sectional area (LMA) caused by corrosion, abrasion, etc. The LMA Signal is quantitative and can be calibrated. (Typically, a rope must be retired when the LMA exceeds 10%).The WRR Signal measures wire rope roughness (WRR). WRR is defined as the aggregate surface roughness of all wires in a rope. WRR is typically caused by and indicates internal and external corrosion pitting, broken wires and clusters of broken wires. The WRR signal is quantitative, and it is calibrated together with the LMA Signal.The LF Signal can indicate localized flaws (LF), for example, broken wires, corrosion pitting, etc. Because it is only qualitative - and cannot be calibrated - it is of limited value for assessing rope deterioration and for making rope retirement decisions.
-
product
Leakage Current Clamp Tester
M-1141
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Auto 5-range : AC 30mA / 300mA / 3A / 30A / 300A・CT inside diameter : φ40mm・Minimum resolution : 0.01mA・Maximum value hold / Data hold function available・Band path filter with center frequency(fo = 55Hz)・Compliant with EN 61010, CAT-III 1000V / CAT-IV 600V・With backlight
-
product
Dead Weight Pressure Tester
Unitech Scales And Measurements Pvt. Ltd
Dead Weight Pressure Gauge Tester is ideal for testing and calibration of pressure gauges,pressure transducers,recorders,digital calibrators etc. The system used in the dead weight is vertically mounted precision lapped piston and cylinder assembly with accurately calibrated mass for loading the piston. Pressure is built easily by single cylinder pump at very high rate. The whole system is housed inside a stainless steel case with elegant look. Pressure ports are provided to fix the gauges to be tested. Acrylic see-through oil tank is designed to use it as oil reservoir.
-
product
Super-Safeway Three Wire Circuit Tester
1301270009
Super-Safeway Three Wire Circuit Tester, 3 Indicating Lights & Receptacle Tension Tester in Carrying Case
-
product
Connection Testers
The level of sophistication of the cable harness tester required will depend on the product type, failure modes and integrity required by the eventual customer. There are 3 main types of test that can be applied and this will determine which of our cable harness testers will be most suitable for your product.
-
product
GFCI & Receptacle Tester
GFCI & Receptacle Tester - GFCI & Receptacle Tester for electrical work.
-
product
Crimp Tester
M004
To calculate the crimp in yarn affected by knitting or weaving, to determine actual yarn usage.
-
product
Ground Resistivity and EarthService Tester
AD-510
Large, readable LCD display (2000 counts), Instant battery life indicator, Test frequency: 128 Hz (quartz generator), Test Voltage: max 30 V peak-to-peak, Range: 0,01 W ? 2 k W. Accuracy resistance measurement: 1 % 2 digits,
-
product
Go No Go Testers
Go No Go Testers are developed in portable formats. Typically these are utilized at 'I' Level and 'O' Level test requirements and clear the aircraft LRU for flight.
-
product
Phase Sequence Testers
UEi Test & Measurement Instruments
Is used for detecting the sequence of the supply in three-phase electric circuits.
-
product
Auto Wire Integrated Tester Series
LX-1024A+
Shenzhen Lian Xin Technology Co., Ltd.
The system provides Chinese/English free switch operation interface,.·Up to 1500Vdc/1000Vac Test Voltage ,.·1024 Max. Test Points ,(Max of all series).·500 Max Files Memory,support USB or PC unlimited expansion,.·Using Embedded Linux operating system,.·Adopted high resolution colour 640*480 TFT LCD ,.·Large 320×240 LCD display ,.·Instant test time :0-60s , optional adjustment..·Providing Single-End ,Multi-segment ,Standard ,and Spot test of wire..·Auto Scan and Auto Pin Search ,.·The system provides advanced instant open-circuit, short-circuit, continuity test,.·Intermittent Conductance Test,.·Intermittent Open/Short Test ,
-
product
Digital Earth Resistance Tester, ERT-1502
Our Earth Tester is a very successful replacement of the conventional generator type hand tester. This device is most extensively used to test the earthing installation in numerous power based industries, electrical traction systems and telecommunication networks.
-
product
80 AMP FUSE BUDDY TESTER
FB315
*Tests circuit current from 0 to 80A*Includes 20A maxi fuse for use with mini and ATC circuit testing*Resolution: .1A (100 mA)
-
product
Multifunction Safety Testers
The new multifunction safety testers of the 1805 and 1886 series combine all the functions of their predecessors and expand them with many features that make your work considerably easier. This includes, for example, the new touch display. With this, all functions can be operated and at the same time the results can be read directly. Thanks to the interfaces available ex works, the 1805 and 1886 series can be easily integrated into your production line or operated "standalone".
-
product
Paessler WMI Tester
WMI allows a process to read out data for many Windows' configuration parameters as well as current system status values. Access can take place locally or remotely via a network connection. WMI is based on COM and DCOM and is integrated in Windows 2000, XP, 2003, Vista and later. Add-ons are available for Windows 9x and NT4.
-
product
Falling Dart Impact Tester
Falling dart impact tester can be used for the determination of impact resistance of packaging materials such as plastic films, laminates by a free falling dart from a certain height. This instrument is designed according to ASTM D1709 with method A & B.
-
product
Electrical Calibration
All calibrations include as Found/as Left data, Measurement Uncertainity, Calibration Sticker, Calibration Certificate and online access to calibration data at NO additional charge.





























