Impact Test
forceful strike to UUT determining strength and durability or detection of loose particles.
See Also: Drop Testers, Pendulum Impact, Impact Hammers, Crush, Hardness Testers, Rupture
-
product
Soldering Test
The soldering tests are conducted to determine if materials can withstand soldering effects, such as resistance to soldering heat, as well as the solderability of components during the manufacturing process.
-
product
Pressure Testing
All metal, plastic, and composite parts intended to contain liquids or gases under pressure are required to undergo stringent pressure testing procedures to meet qualification standards.
-
product
Test Labs
ART-MAN
ART-MAN uses 285 100% vector sensors per SAM phantom and 390 sensors in the flat body phantom to take accurate measurements based on state-of-the-art near-field theory.
-
product
Test Equipment
ST9020
Shenzhen Star Instrument Co., Ltd.
The ST9020 single-phase energy meter test equipment is full-featured and stable. Optional accuracy classes are 0.1 and 0.05. As divided by structure there are combined type, integrated type and auto wiring type. The meter test equipment is controlled via PC-based software. Choices of meter position are 6, 12, 24, 30, 48 and 60.
-
product
Quality Tests
Phoenix Contact has been developing innovative products for electrical connection and automation technology for over 90 years. To ensure the quality of these products, they are tested on the basis of various directives and standards throughout the entire process of creation. As a result, the products can be integrated in a variety of industries under a wide range of environmental conditions.
-
product
Flame Testing
Helping you ensure acceptable flammability and flame resistance for electronic products and components.
-
product
In-Circuit Testing
If you are looking for in-circuit test applications, equipment or advice, our experienced engineers can help you. Whatever your fixturing requirements or special software features, our long history of work in this field means that we have probably seen and done it before.
-
product
FPGA Testing
Silicon Turnkey Solution, Inc.
The secret to our success in the FPGA testing field is the STS hammer file, a proprietary test methodology based on our experience testing thousands of unique FPGA designs. The hammer file is designed to program the FPGA to its maximum combination and block configuration and then tests the completely programmed FPGA for full dynamic, DC and at-speed AC performance. Power and transient tests are also conducted under worst-case populated configurations. Application-specific usage configurations are also used to assist in generating the worst-case electrical specification limits at worst-case environmental use.
-
product
Test Handler
HA1200
The new HA1200 handler can be linked with a tester to utilize our unique active thermal control technology for testing singulated and/or partially assembled dies. This technology enables testing of powerful high-end SoCs with 100% test coverage. This helps reduce yield loss at final test, thus reducing losses of final multi-die assembled products.
-
product
In-Circuit Testing and Test Engineering
5184 Test NodesHPUX or Windows60 Mhz ASRU Frequency Counter, Timer10 Mhz Clock, 6 Mhz data ratesVector Test for VLSI, PLCC & ASICSTestjet and VTEP Vectorless TestingAdvanced Boundary ScanSilicon Nails AvailableSeries V upgradeable
-
product
IPTV Testing
EXFO offers IPTV test solutions to assess the network copper physical layer, validate the xDSL service and test the performance of the IPTV component at any stage of the deployment. Our Ethernet IPTV testing, IPTV analysis capabilities and advanced IPTV monitoring solutions offer complete end-to-end quality of experience (QoE) assessment for IP video. EXFO enables providers to successfully introduce video services faster and manage them more cost-effectively, by continually ensuring the highest service quality.
-
product
Test Software
American Probe & Technologies, Inc.
This new series of software allows you to analyze materials or semiconductor leakage with all of the capabilities of your HP 4140B to resolutions of 1 fA @ 100VDC. Completely rewritten in Visual Basic for Windows XP operating system, it offers Virtual Front Panel Operation of 4140B for I-V & CV Analysis and allows operator to virtually control the 4140B for any instrument operation. I-V Plots with options of displaying current over time. CV Plots with high resolution plotting capability.
-
product
Magnet Testing
RMP Rotor Measuring Station
The RMP Rotor Measuring Station is a universal measuring system for the precise measurement and quality control of multi-pole permanent magnet rotors.
-
product
Environmental Testing
Among AMERICAN TESTING LABORATORY's environmental chambers is a walk-in stainless steel chamber, which is 40 feet long, 20 feet wide and 8 feet high. One of the largest environmental chambers owned by an independent testing organization in the nation, it allows for simulated environmental testing under conditions ranging from subzero to 200° F with a relative humidity of 5% to 100%, with a ±2% tolerance.
-
product
Microwave Testing
170
The PICOPROBE® MODEL 170, a high performance microwave probe which incorporates a WR-6 waveguide with our patented coaxial design techniques, has inherent low loss and low dispersion characteristics.
-
product
Electromagnetic Testing
Xiamen IDEA Electronic Technology Co., Ltd.
Is the process of inducing electric currents or magnetic fields or both inside a test object and observing the electromagnetic response.
-
product
Test Extender
PMC
The PMC test extender provides an active interface between a PMC carrier slot (PCI bus) and a PCI Mezzanine Card (PMC).
-
product
Manhole Impact Tester
Manhole Impact Tester is used to test the impact performance of manhole base and manhole wall.
-
product
Sync Test
Paragon neo-S
Capture and decode PTP packets for analysis and Time Error testing. PTP clock emulation, plus the Paragon neo-S’ conformance test applications, removes uncertainty and maximizes test repeatability – essential for validating new, high-accuracy 5G network devices.
-
product
Noise Figure Analysis Using NI PXI RF Test Instruments
NI-RFmx Noise Figure
Measure noise figure, gain, Y-factor, effective temperatures, hot and cold power, and moreOptimized calibration and measurement routines for multi-DUT test using Y-factor and cold sourceSupports the PXIe-5668R 26.5 GHz VSA, the PXIe-5698 26.5 GHz preamplifier, and VSTsDesigned for use with industry-standard noise sources such as the Noisecom NC346 Series
-
-
product
Leakage Test
Leakage current and discharge current depend on the insulation of the device. The measurement simulates various fault situations that could occur during operation. The test determines whether the measured current is within the permissible limits and poses no danger to the user in case of a fault.
-
product
Test Sockets
Smiths Interconnect offers a wide range of spring contacts and design standards for high quality test sockets providing flexibility and fast delivery for optimal cost/performance ratio.
-
product
Function Test and In-Circuit Test
CT350
ICT test points: max 2736 CAD Data import Automatic program generator Powerful debugging tools Test coverage analysis Paperless repair station Logging- and statistic functions Full graphical functions Panel and multisite tests Fast adapter exchange High Pin Count-Interface On table optional usable shelf part.
-
product
OTP-Based Test System
Power electronics assemblies often cannot be tested using conventional technology for their electrical performance. Due to the adaptability of the instrumentation, the OTP concept offers an ideal platform even beyond the space requirements of several control cabinets. In order to achieve high test flexibility with different assemblies, the system was equipped with three-phase AC sources and AC loads as well as a precise three-phase power meter. DC sources and loads with different current and voltage ranges cover the test of frequent DUT operating parameters. Time-dependent voltage or current signals can be stimulated by an arbitrary generator with power amplifier. General measurements such as current, voltage, frequency, resistance can be carried out flexibly at various test points using the matrix concept. An oscilloscope with RF multiplexer is available for high-frequency measurements such as residual ripple, switching processes, etc.
-
product
Low-Temperature Impact Device
DWC-1
This low-temperature impact device is compliance with standard requirement of IEC60245, IEC60227, IEC60540, GB5013-2008, GB5023-2008 and GBT2951-2008. It’s used to test all kinds of PVC sheathed cable, wire, soft wire and no sheath of parallel soft PVC insulated impact resistance at low temperature. Specification: • Working temperature: -15℃±1℃ • Impact height: 10~200mm adjustable • Length of specimen: 5D~150D • Material: 304 stainless steel • Completion time once: 3~5s • Completion number of units for once: ≥2pcs • Weight: 100/200/300/400/500/600/750/1000/1250/1500g • Low temperature box to match additionally
-
product
Sample Test
For performance evaluation and model selection at the time of your purchase, we have welding laboratories at our Shin-Yokohama facility where you can perform welding tests using actual equipment.
-
product
Automated Testing
IRWindows™5
IRWindows™5 from Santa Barbara Infrared is an advanced software tool that automates the setup, execution, data collection and results analysis for industry standard performance testing of infrared, visible and laser systems. IRWindows™5 is the most advanced commercially available IR/EO sensor test software package in the industry today. It operates under Windows™ OS and is delivered installed on a high-end PC computer platform with frame grabber(s) selected to support UUT video formats. It is also available as a software only package. IRWindows™5 combined with SBIR target projectors provides test engineers and technicians a turnkey, automated hardware/software solution for full-spectrum sensor testing.
-
product
Radio Testing
Testing of radio systems. PHOENIX TESTLAB as an accredited radio testing laboratory, Notified Body for R&TTE Directive 99/5/EC and Conformity Assessment Body offers you a complete service up to your products' worldwide introduction to the market.
-
product
Test Automation System for Brake Testing
STARS Brake
STARS Brake is an integrated automation, data acquisition and control system platform that provides a comprehensive application functionality in a single, powerful environment. STARS Brake is designed to address the needs of a wide range of brake testing applications from component development to final component and system validation. It offers users a level of flexibility and openness that enables thorough investigations of brake systems.
