Transceivers
both send and receive a signal.
See Also: Optical Transceivers, Vector Signal Transceivers, SFP, SFP Test
-
Product
Zynq Ultrascale+ MPSoC (ZU19/17/11EG) 3U-VPX Plug-in Module
iW-RainboW-G35V®
FPGA Module
AMD Xilinx’s ZU19/17/11EG Zynq Ultrascale+ MPSoC64bit, 8GB PS DDR4 RAM with ECC (Upgradable)Dual 64 bit, 8GB PL DDR4 RAM (Upgradable)8GB eMMC Flash (Upgradable)3U VPX Connectors based on ANSI/VITA 46.30 (P0+P1A & P1B+P2A)8 Optical transceivers through MT Ferrule Connector (P2B) based on VITA66.4
-
Product
2-channel RF Transceiver Module
FMC30RF
-
Sundance Multiprocessor Technology Ltd.
The FMC30RF is an FMC Daughter Card which is fully compliant with the VITA 57.1-2010 standard. The FMC30RF offers in a small footprint a low power and fully featured Rx / Tx signal path for the development and deployment of advanced RF solutions. With a frequency range coverage from 400MHz to 3.0GHz* and up to 60MHz* bandwidth the FMC30RF provides flexibility and reconfigurability to a host of applications.
-
Product
Digital I/O Cards
104-DIO-48E
-
The circuits use an 82C55A PPI with mode 0 supported. Ports A, B and C are buffered with 74ABT245 transceivers and pulled up to 5V. The optional 82C54 has three-sixteen bit down-counters within one chip. These counters are useful for making frequency outputs, measuring frequency of square waves, pulse width outputs, pulse width measurements etc. Software drivers are provided on CD.
-
Product
PCI Module
PCI-1553-DDC-1,2
-
The PCI-1553-DDC uses Data Device Corporation’s ACE, DDC enhanced mini BU61865G4-290 communication device as its 1553 bus controller, or remote terminal, or monitor terminal. A single controller has two redundant channels. This controller has 64Kx17 word of internal memory and internal transceivers for both channel A and B. The 3U PCI board has on-board transformers. This board has a PCI compliant interface
-
Product
Digital Video/Audio/Data optical transceiver
OD3000B
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai OD3000B digital series optical transceiver, adopts digital video coding technique and WDM technique to satisfied user's multipath digital video, audio, data, ethernet's long distant high quality optical fiber transmission because of its full-found. This model of optical transceiver including single fiber one way digital video, single fiber 64 routes video, 128 routes audio and data uni-direction and bi-direction complication. OD3000B optical transceiver can transmit the camera audio/video signal, camera and tripod head control data as well as other control function to central control room from remote end by optical fiber. It can be widely used in the remote monitoring, video conference, video medical, remote education and other systems of public road, traffic, industrial and mining, community ect.
-
Product
Attenuation Control Unit, DC to 18 GHz, 0 to 121 dB, 1-dB Steps
J7201B
Attenuator
Designed for WLAN and WiMAX™ device manufacturing test and mobile handset base transceiver station (BTS) handover test.
-
Product
Transceivers
-
Macom Technology Solutions Holdings Inc.
At MACOM we offer monolithic and stereo Doppler transceivers for directional motion detection. Our transceivers are used in a variety of applications such as automatic door openers, ground speed recorders and police radars. MACOM’s transceivers are well suited for high volume applications where small size and reliability are required.
-
Product
Transceivers
-
ST offers monolithic ICs containing standard ISO 9141 compatible interface functions and bidirectional transceivers for signal conditioning that operate with a CAN controller and meet ISO/DIS 11898 up to 1 Mbaud.
-
Product
Interface RS-232
-
The RS-232 specification allows for reliable data transmission from one transmitter to one receiver at data rates of up to 20 kbps over relatively short distances (up to 50 feet). On more recent RS-232 transceiver chips, data rates of up to 1 Mbps are achievable over shorter distances (up to 5 feet). The most common applications for RS-232 transceivers are computers and peripherals, mobile phone data cables, and diagnostic data ports.
-
Product
PXI Vehicle Multiprotocol Interface Module
Interface
PXI Vehicle Multiprotocol Interface Modules use hardware-selectable NI-XNET Transceiver Cables (TRC) to communicate High-Speed/Flexible Data‑rate CAN, Low-Speed/Fault Tolerant CAN, and/or LIN. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN and/or LIN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. PXI Vehicle Multiprotocol Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
Serial Interface Device
Serial Interface
The Serial Interface Device offers a number of options for connecting to serial hardware. You can choose from Ethernet, USB, PCI, PCIe, or ExpressCard interfaces to add up to 16 serial ports to your system. You can choose from common serial protocols, such as RS232, RS422, and RS485. The Serial Interface Device also offers various isolation, hyperthreading, and multiprocessor compatibility options. Some models also support 4- and 2-wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PXIe Arbitrary Signal Generator and Transceiver
-
The Tabor Proteus Series P948xM, P9082M, P258xM and P128xM models are arbitrary signal transceivers based on the PXIe platform. The modules combine transmit, receive and digital signal processing capabilities in a single device. The modular, compact and cost-effective systems offer unique performance, various configuration options, innovative task-oriented programming and a user-programmable FPGA.
-
Product
PXIe-7915, KU060 FPGA, 4 GB DRAM, x8 Gen 3 PXI Coprocessor Module
785174-01
Digital I/O Module
The PXIe-7915 provides a Xilinx Kintex UltraScale FPGA that you can program with LabVIEW or Xilinx Vivado to add signal-processing capabilities to PXI Express systems. Using the x8 Gen 3 PCI Express architecture and peer-to-peer streaming, PXI FlexRIO Coprocessor Modules can stream data to and from other modules in a PXI chassis at up to 7 GB/s without a host controller. You can pair these modules with another PXI instrument, such as a PXI Vector Signal Transceiver, to add functionality, such as running complex algorithms in real-time. The PXIe-7915 KU060 FPGA is ideal for RF applications that require a substantial amount of signal processing.
-
Product
Fiber Optic Test Solution
Eye-BERT Micro 10G
-
The Eye-BERT Micro 10G is a low cost, easy to use, all-in-one XFP based fiber optic test solution offering high performance bit error rate testing at a fraction of the cost while providing a rich set of features not found in other bit error rate testers. Features include: variable bit rate, user programmable patterns, diagnostic monitoring, and wavelength tuning (per XFP capability). Additionally, with a click of a button, the Eye-BERT Micro 10G will automatically test an XFP module based on the information it reads from the transceiver and generate a detailed test report complete with manufacturer, part number, serial number, date code, fiber type, link length, speed, and test results. The Unit is supplied with anti-skid bumpers and is small enough to be integrated into larger systems for dedicated link verification.
-
Product
USB
-
Universal serial bus, or USB, is an industry standard that defines the cables, connectors and communication protocols used to connect computers and peripherals. ST's portfolio covers a wide range of products designed for USB data (transceivers) and/or power applications (battery chargers and charger detection systems).
-
Product
Non-Isolated Controller Area Network (CAN)
-
ADI nonisolated controller area network (CAN) transceivers provide the differential physical layer interface between the data layer link, hardware protocol (for example, embedded in some of ADI's Blackfin® processors), and the physical wiring of the CAN bus. ADI's portfolio includes transceivers with integrated iCoupler® and isoPower® isolation, providing, fully isolated off-the-shelf CAN PHY's.
-
Product
DUAL RF Multiple-Input/Output
FMC-SDR400
-
Sundance Multiprocessor Technology Ltd.
FMC-SDR400 is a Dual RF multiple input/output module (MIMO) based on AD9361, 70MHz – 6GHz RF transceiver and AD9656 ADC for baseband sampling of less than 70MHz (input only in this range). A software selectable gain and tunable RF bandpass front-end section provides high RF sensitivity by allowing rejection of out-of-band-of-interest interfering signals.
-
Product
PCIe Mini CAN Controller
PCie-Mini-CAN-FD
Controller
The PCIe-Mini-CAN-FD is a PCI express controller with an integrated CAN FD transceiver supporting data rates up to 8Mbps. The CAN FD controller meets the specifications of the ISO11898-1:2015 high speed Controller Area Network (CAN) data link layer and meets the physical layer requirements of the ISO11898-2:2016 high speed CAN specification.
-
Product
PXIe-5644, 6 GHz, 80 MHz Bandwidth, RF PXI Vector Signal Transceiver
782376-01
Vector Signal Transceiver
6 GHz, 80 MHz Bandwidth, RF PXI Vector Signal Transceiver—The PXIe‑5644 combines a vector signal generator and vector signal analyzer with FPGA-based real-time signal processing and control into a single device, also known as a VST. Because of this software-designed approach, the PXIe‑5644 features the flexibility of a software defined radio architecture with RF instrument class performance.
-
Product
Wireless Connectivity
-
A product portfolio for advanced WiFi solutions that support 802.11ax/ac/n/a/g/b standard and wireless RF transceivers that operate in the sub-GHz and 2.4 GHz bands.
-
Product
*C Series CAN Interface Module
CAN Interface
C Series CAN Interface Modules communicate using onboard transceivers for High-Speed/Flexible Data‑Rate or Low-Speed/Fault Tolerant CAN. C Series CAN Interface Modules are either compatible with NI-XNET or the NI-985x driver, depending on model.Using NI-XNET, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series CAN Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
Hydrographic Grade Deepwater Singebeam Echosounder
DESO 5DS
-
The DESO 5DS is a hydrographic grade deepwater singlebeam echosounder designed for reliable high performance in deep ocean surveys. It utilizes very high power transceiver electronics to survey the oceans down to 10km depth.The raw data record is stored in proprietary format by Teledyne’s own software and can be acquired, replayed, and analyzed similar to thermal paper records. Depth data is continuously generated on serial and network interfaces and can be recorded by hydrographic software.The DESO 5DS is based on our latest singlebeam sonar technology, designed as a precise and reliable survey tool for the survey from shallow waters to full ocean depth.The DESO 5DS utilizes the most robust automatic control and bottom detection algorithms available — providing you with precise depth information and brilliant water column profile even under the most challenging conditions.
-
Product
TRC-8542, CAN HS/FD Transceiver Cable
783699-02
Transceiver Cable
CAN HS/FD Transceiver Cable—The TRC-8542 is designed to provide flexibility in connecting a CAN bus to the NI-9860, PXIe-8510, and/or the native NI-XNET port on a cDAQ-9134 or cDAQ-9135 controller. You can connect the TRC-8542 to the port to support a CAN HS/FD. The TRC-8542 is an isolated cable that includes the necessary transceiver for the bus type. It also features termination resistors that you can enable or disable in software.
-
Product
Bit Error Rate Tester - MATRIQ
Tester
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
Product
Vector Signal Transceiver-based Radio Solution (VRS)
ATS-3100 VRS
Vector Signal Transceiver
The ATS-3100 VRS, the newest member of the ATS-3100 PXI Integration Platform product family and fifth-generation radio test solution, is a single, consolidated platform for testing legacy, modern, and next-gen, software-defined radios for military, civil, and commercial users. Integrating the PXI Vector Signal Transceiver (VST) from National Instruments (NI), the platform enables faster test time with wider bandwidth (up to 1GHz) than any other radio test solution available today.
-
Product
XMC - Module VITA61/42
XMC-1553-2-IO
Communications Module
The XMC-1553-2-IO-2 uses a DDC® Total-ACE® communication device as its 1553 bus controller, or as a remote terminal with concurrent bus monitor terminal. Dual controller has a dual redundant channel with built in transceivers and transformer. The controller has the capability to emulate up to 31 RT addresses simultaneously.
-
Product
Direct Attach Cables
-
Shanghai Tarluz Telecom Tech Co., LTD
Are copper cable assemblies made from twinax cable, terminated with transceiver housings on each end.
-
Product
HF Communication Equipment
MS 2000
-
The Meltronics HF/SSB system provides a reliable voice communication over 2 to 29.99MHz frequency range and is designed to meet the most diverse requirements. The HF system is used to establish communication between Air to Ground station, Air to Air and Air to Ship. This System is suitable for Aircraft, Helicopter and Ships communication applications. The HF transceiver has beyond line of sight communications providing both voice and data services. Systems is a digital, Microprocessor controlled, synthesized unit that utilizes DSP technology to increase performance and versatility.
-
Product
PCI Extender Card for cPCI Systems
DP-cPCI-7497
-
The DP-cPCI-7497 is highly flexible PCI Extender card, which can be used to extend PCI / PCI-X bus from one system to another system over an optical fiber medium upto 500m distance. A PCI-X to PCI-e Bridge is used to convert the PCI / PCI-X protocol to x4 PCI Express protocol operating at 2.5Gbps.The PCI-X to PCI-e Bridge is connected to four optical transceivers (x4 PCI- e link) which can transmit optical signals upto 2.5Gbps speed.A x4 copper medium connection option in lieu of optical transceivers is also available.
-
Product
Test Solution
Eye-BERT MicroX
-
The Eye-BERT MicroX is a compact, easy to use test solution offering high performance bit error rate testing at a fraction of the cost of competing solutions. The unit is offered in two speed grades including the X10 which operates up to 14.5Gbps, and the X30 which extends the data rate to 29Gbps. Its broad data rate capabilities and long test patterns make this unit suitable for testing nearly all optical SFP, SFP+, and SFP28 transceivers in production with just one unit. The real-time eye opening monitor and eye scanning capability can aid in troubleshooting by providing the operator with additional link quality information. Other features include Autonomous pattern detection, SFP diagnostic tools, and wavelength tuning (per transceiver capability). With a click of a button the Eye-BERT MicroX will automatically test an SFP module based on its advertised capabilities and generate a detailed test report complete with manufacturer, part number, serial number, date code, fiber type, link length, speed, and test results. The Unit is supplied with anti-skid bumpers and is small enough to be integrated into larger systems for dedicated link verification.
