Position Sensors
-
product
Inductive Motor Control
The inductive motor control position sensor family detects the electrical position within one pole-pair of a rotating shaft and can be used for the motor commutation of a brush-less DC (BLDC) motor. Based on the inductive sensor technology, this family measures the coupling between an excitation coil (TX) and two receiver coils (RX) via a rotating target. The coils are executed as printed circuit coils and the rotating target is a simple punched metal part. With the correct layout of the coils and the target, both synchronized to the number of pole-pair count of the motor, the IC output is proportional to the electrical angular position within one pole-pair segment with increased resolution and high performance of only 0.3° electrical INL!
-
product
Absolute Optical Encoder Kit Version
A2K
The A2K absolute encoder is a non-contacting optical rotary position sensor which reports the shaft angle within a 360 deg. range. As opposed to incremental encoders, the A2K reports the absolute position rather than the change in position. When powered up, it does not require a home cycle, even if the shaft was rotated while the power was off. In multi-turn mode, it tracks the position in a 32-bit counter as long as the power supply is maintained. Internally, an infrared LED flashes through a circular bar code onto a linear array sensor. The microcontroller decodes the image into a unique position. All user programmable parameters such as resolution, origin, direction and mode are permanently stored in an internal EEPROM
-
product
Potentiometer for OEMs
FlexiPot
The best user interface, whether in consumer electronics or industrial controls, contains sensors that cause minimal interference, meaning the user may not even know they are there. FlexiPot, by Tekscan, is a flexible membrane potentiometer with an ultra-thin (0.008"), lightweight profile. Low power requirements combined with a linear output make it the ideal position sensor, from both a manufacturing perspective as well as a user perspective.
-
product
Absolute Optical Encoder
A2
Product DescriptionRestriction of Hazardous SubstancesThe A2 absolute encoder is a non-contacting optical rotary position sensor which reports the shaft angle within a 360 deg. range. As opposed to incremental encoders, the A2 reports the absolute position rather than the change in position. When powered up, it does not require a home cycle, even if the shaft was rotated while the power was off. In multi-turn mode, it tracks the position in a 32-bit counter as long as the power supply is maintained. Internally, an infrared LED flashes through a circular bar code onto a linear array sensor. The microcontroller decodes the image into a unique position. All user programmable parameters such as resolution, origin, direction and mode are permanently stored in an internal EEPROM
-
product
Rotary Position Sensors
We offer a full range of Rotary Position Sensors, in a variety of housings, utilising wirewound, cermet and conductive plastic technology.
-
product
Linear Motion Potentiometers
A spin-off of the Trimpot trimming potentiometer product line, the linear motion potentiometer was developed to meet the needs of designers wishing to detect movement of position. Applications for these compact components include: Solenoid positioning sensors for automated controllers, volume control on audio equipment, joystick controllers, satellite dish positioning, and robotics.
-
product
10 MHz To 67 GHz LAN Thermal Vacuum Compliance Power Sensor
L2067XT
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
product
Thermocouple Power Sensors
N8482H
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
product
E-Series Peak and Average Power Sensor, 50 MHz to 18 GHz
E9326A
The E9326A power sensor has a 1.5 MHz video bandwidth and is ideal for time-gated peak, average and peak-to-average ratio power measurements on TDMA and CDMA wireless formats such as Bluetooth.
-
product
Power Sensor
8483A
The 8483A diode power sensor measures average power over the frequency range 100 kHz to 2 GHz and power range -30 to +20 dBm (50 dB dynamic range).
-
product
Thermocouple Power Sensors
N8482B
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
product
Thermocouple Power Sensors
N8488A
N8488A power sensor has the widest frequency range among N8480 power sensors offering from Keysight.
-
product
10 MHz to 33 GHz LAN Wide Dynamic Range Average and Peak Power Sensor
L2063XA
The Keysight L2063XA is a fast, accurate and wide dynamic range 10 MHz – 33 GHz LAN peak power sensor.
-
product
10 MHz – 6 GHz USB Power Sensor
U2001B
U2001B USB power sensor measures average power over the frequency range 10 MHz to 6 GHz and power range -30 dBm to +44 dBm.
-
product
Thermal Power Sensors
NRPxxT/TN/TWG
The R&S®NRP power meter sensors have long been recognized for delivering supreme precision and speed. The R&S®NRPxxT, R&S®NRPxxTN and R&S®NRPxxTWG thermal power sensors are especially used for complex measurement tasks where highest accuracy counts
-
product
Diode Power Sensor
8487D
Excellent SWR for reducing mismatch uncertainty Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter Accurate average power measurements over -70 to -20 dBm Frequency range 50 MHz to 50 GHzDiode power sensing element
-
product
10 MHz To 67 GHz LAN Wide Dynamic Range Peak And Average Power Sensor
L2067XA
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
product
Differential Sensor, Wide Dynamic Range, 100 MHz
CX1105A
The CX1105A ultra-low noise differential sensor is a dedicated accessory for the CX3300 series and enables dynamic current measurements from 1 μA to 100 A under up to 100 MHz bandwidth with existing shunt resistors on your test board.
-
product
DC/10 MHz 67 GHz USB Thermocouple Power Sensor
U8488A
The U8480 series is Keysight's first power sensor with the capability to measure down to DC (only applicable for U8481A/85A). Now, with an expanded frequency range up to 50 and 67 GHz, the U8480 series allows you to make fast and accurate high frequency power measurements in applications ranging from PNA/MXG calibration to high volume manufacturing.
-
product
18-Channel LED Analyzer
AL568
The format of the AL568 optical fiber for LED test is the most convenient and effective system on the market. It sits in the space of a 90 Series VPC module and only requires connection to a USB port to get data from up to 18 LEDs.
-
product
Peak And Average Power Sensor, 50 MHz - 6 GHz, 5MHz Bandwidth
E9323A
The E9323A power sensor has a 5 MHz video bandwidth and is ideal for time-gated peak, average and peak-to-average ratio power measurements on W-CDMA wireless formats such as cdma2000.
-
product
10 MHz to 33 GHz USB Wide Dynamic Range Average Power Sensor
U2053XA
Your product description goes here.The Keysight U2053XA is a fast, accurate and wide dynamic range 10 MHz – 33 GHz USB average power sensor.
-
product
10 MHz To 50/53 GHz LAN Wide Dynamic Range Average Power Sensor
L2055XA
The Keysight L2055XA is a fast, accurate and wide dynamic range 10 MHz – 50/53 GHz LAN average power sensor.
-
product
USB Power Sensor Module For Measuring Receiver
U5532C
The U5532C USB power sensor module is specially design for the N5531X measuring receiver. Based on the Keysight USB power sensor and a power splitter, the U5532C provides the N5531X measuring receiver user with a single RF input device covering up to 50 GHz. Using of the U5532C USB power sensor module eliminates the requirement of an external power meter, simplifying the setup process and saving lab space. The measurement integrity and accuracy are guaranteed by the fully defined specification sets. The traceability of measurement uncertainties is also ensured.
-
product
Thermocouple Power Sensors
N8481A
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
product
10 MHz to 18 GHz USB Wide Dynamic Range Average & Peak Power Sensor
U2062XA
The Keysight U2062XA is a fast, accurate and wide dynamic range 10 MHz – 18 GHz USB peak power sensor.
-
product
10 MHz To 54 GHz LAN Thermal Vacuum Compliance Power Sensor
L2066XT
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
product
Power Sensor and SNS Noise Source Cables (3 m/10 feet)
11730B
The Keysight 11730 series power sensor cables are used with the 8480 and E-series power sensors (except the E9320 family of peak and average sensors). These cables are designed to reduce RFI effects on low power readings with an improved shielding design in the cable itself. Cables may be ordered individually or in pairs in any combination desired for single and dual-channel measurements.
-
product
10 MHz - 18 GHz USB Power Sensor
U2000A
U2000-series USB Average Power Sensor enable fast, simple setup by providing plug-and-play USB connectivity and by eliminating the need for a separate power meter.
-
product
E-Series Average Power Sensor
E9304A
Refer to the E9301A for standard power sensor features Low frequency coverage (9 kHz to 6 GHz) for EMC/EMI test applications such as the radiated immunity test (IEC61000-4-3)High sensitivity (-60 to +20 dBm) and fast measurement speed to reduce the time taken to calibrate radiated field uniformity and EMC/EMI test receivers Measure transmitter power and receiver sensitivity at Very Low Frequency (VLF) to microwave frequencies Special option available to 18 GHz Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters
