-
product
PoE Tester
PE-100
The PoE Tester/Power Monitor is designed for testing standard PoE and measuring power of PoE systems, by performing both PSE (Power Source Equipment) detecting and PSE/PD (Powered device) inline testing. Compliant with IEEE802.3 af, 802.3at standard and 802.3bt ultra 4-pair up to 60W-100W. PSE detecting display PoE type (af or at), power source (Endspan or Midspan) and perform a load test for voltage drop with REV LED indicates a reversed power. Inline PSE/PD testing-measure and display in rotat...show more -
product
Audio Multimeter
AMM-1
The purpose of this tool is to enable the user to: Measure True Amplifier Power output into any load reactive or resistive Measure Common DC voltages Measure DC voltage drops during quick transients on cable runs or battery / charging systems Measure Impedance of speakers at any power or frequency from 20Hz - 1kHz (box rise) Measure Phase Difference between Voltage and Current into reactive loads (Power Factor) Find Tuning Frequency of subwoofer enclosures Tune subwoofer enclosures for maximum power transfer Measure AC Volts (amplifier output) Measure AC Amps (amplifier output)
-
product
Mezzanine System
5658
ECM P/N 5658 provides eight channels of 16 bit current measurement in the 0 to 25 milli-amp range. Each channel allows independent common mode voltages from -100 volts to +100 volts. Current detection is accomplished with a precision 100 ohm current sense resistor, creating a voltage drop of 2V in the current loop at 20 milli-amps.
-
product
Digital Multimeters
ST-3201
Standard Electric Works Co., Ltd
● Display : 3½ digit liquid crystal display (LCD) with max. reading of 1999.● Polarity : Automatic, (-) negative polarity indication.● Zero Adjustment : Automatic.● Over Range Indication : Highest digit of (1) or (-1) is displayed. ● Low Battery Indication : The (BAT) is displayed when the battery voltage drops below the operating voltage.● Measurement Rate : 3 measurements per second, nominal.● Operating Temperature : 0ºC ~ 50ºC, 70% R. H.● Storage Temperature : -20ºC ~ 60ºC, 80% R. H.● Accuracy : Accuracy specifications at 23 ± 5ºC, less than 75% R. H.● Power : Single, 006P 9 volt battery● Dimensions : 128(L) × 72(W) × 33(D) mm.● Weight : Approx. 183g
-
product
Battery Monitor
BAF-M2
Schumacher Electric Corporation
BATTERY MONITOR• Plugs into a 12 volt automotive cigarette lighter receptacle• Allows instant monitoring of battery & charging system voltage• Constant automotive battery and charging system check with a digital readout• LED warning lights alert you when your battery or charging system is not functioning properly• Detects charging input voltage within 0.1 volts variance• Detects problems with the alternator, diode and any variance of more than 0.8 volts• Alerts you once battery drops to 12.0...show more -
product
Load Cell Power Supply
MODEL PSMR
The PSM-R is a self contained AC power bridge excitation supply. This device consists of a low interwinding capacitance AC transformer and a high stability adjustable linear regulator designed specifically for driving transducer bridges. DC excitation is adjustable from 4 to 15 volts output and is capable of supplying 0 to 150 mA in output current. It features remote sensing to eliminate line drop errors and very low noise. It can also be used as a high quality voltage source or reference in many applications. AC input requirements are 105 to 125 VAC at 60 Hz.
-
product
Milli Volt Drop Test Set
Widely used for testing transformer and switchgear, this equipment is available to clients in different capacities.
-
product
4 Digit Field Indicator
CFIA-40 4
Chuan Sheng Electronics Co., Ltd.
1. Using LED to display, and able to be used in dark environment2. No external power needed3. Able to display measured value like pressure , temperature and depth etc4. Display solution 1/99995. Isolated alarm open drain output6. Voltage drop will below 4 volt
-
product
Digital Multimeters
ST-3501
Standard Electric Works Co., Ltd
● Display: 3½ digit liquid crystal display (LCD) with max. reading of 1999.● Polarity: Automatic, (-) negative polarity indication.● Zero Adjustment: Automatic.● Over Range Indication: Highest digit of (1) or (-1) is displayed.● Low Battery Indication: The (BAT) is displayed when the battery voltage drops below the operating voltage.● Measurement Rate: 3 measurements per second, nominal.● Operating Temperature: 0°C to ±50°C, 0-70% RH.● Storage Temperature: -20°C to +60°C, 0-80% RH, with battery removed.● Accuracy: Accuracy specifications at 23±5°C, less than 75% RH.● Power: Single, 006P 9 volt battery● Dimensions: 128(L)×72(W)×33(D)mm.● Weight: Approx .200g
-
product
Drop Tester
AccuDrop 160A
Model AD-160A is 1 of 3 models in the ACCUDROPTM Series. It helps determine the ruggedness of packagesand the effectiveness of their interior cushioning when exposed to impact during material handling. Theeffects of dropping are easily duplicated in your laboratory using the controlled and precise flat, corner, andedge drop tests.
-
product
Drop Tester
KD-2768
King Design Industrial Co., Ltd.
Drop tester is applied to test the anti-vibration, covering-protection capability of packaging material, or product’s impact-resisting capability to determine the improvement parts of related packing design, material and structure. It contribute to promote the packing material and product’ strength. According to the result of packing drop test, you can judge whether the product has reach the required strength encountered in future. Through doing the drop testing of product independently, you’ll know its affordability to withstand external impact and assess the damage.
-
product
Service Drop Locator
VM-560
The VM-560 is a general-purpose locator used to detect buried pipe and cable services in a variety of situations. With a 50/60Hz passive power locating frequency and three active frequencies, the VM-560 locator will meet the requirements of those wishing to detect the presence of active power cables and to trace short ranges. The VM-560 transmitter also has the additional frequency of 8kHz Fault-find so it can be used to detect the presence of ground to sheath faults on cable when used with the VM-510 Stand Alone A-Frame fault locator.
-
product
Microvolt DC Volt Meter
QA350
The QA350 relies on a built-in reference to calibrate the ratio between the hi and low ranges. If you have a preferred lab reference, you may use that it to improve the QA350 accuracy beyond the indicated +/- 400 PPM. For example, various vendors on eBay can provide calibrated +/-30 PPM 5 or 10V voltage references that can be used to set the ultimate accuracy of the QA350 to under 50 PPM at room temperature.
-
product
Drop Testers
This process is vital for ensuring that products travel to customers safely and securely, eventually arriving damage free. In turn, drop test systems help companies save money and maintain positive brand-owner reputations by helping to design packaged products that will deliver products with their intended inherent quality intact. Lansmont Drop Test Systems are the gold standard for accurate and repeatable drop testing. Every drop tester we manufacture is factory-tested to ensure it meets flatness-of-drop requirements and exceeds industry specifications.
-
product
Drop Weight Tear Tester
DWTT
Since the introduction of the Drop Weight Tear Tester - DWTT, materials have moved on. In particular, demands for high operating pressures of line-pipes and larger diameters have driven the development of higher strength steels. Forty years ago the work that led to the drop weight tear test was done on X52 steel (360MPa yield strength). Improvements in thermo-mechanical processing has yielded improvements of approximately 10,000psi per decade, to the point where the state of the art is now X100 steels, and the use of X120 steels is being considered.
-
product
Geotextile Cone Drop Tester
TG015
TESTEX Testing Equipment Systems Ltd.
Geotextile Cone Drop Tester, to determing the resistence of cone drop from certain height.
-
product
6/12 Volt Digital Volt Meter
12-1011
• 6/12 Volt Digital Volt Meter• Light weight accurate 6/12 Volt Digital Volt Meter• Check charging system and battery voltages• Reverse hook-up protection• Four digit display• OCV state of charge percentage for both batteries AGM and Flooded
-
product
Volt Probe & Socket Testers
Non-Contact & Socket
Use Amprobe non-contact volt probes to safely check circuit breakers, wall sockets and fuses for voltage presence with portable, economical tools. For sockets, choose an Amprobe socket tester, which can confirm whether GFCI breakers are properly wired.
-
product
Drop & MDU Products
Next-generation solutions for fortifying and futureproofing your outside plant environment, including MDU (multiple dwelling units), drop and customer premise products.
-
product
Loading Adjustable Drop Tester Machine
CX-DL15A
Shenzhen Chuangxin Instruments Co., Ltd.
Package Impact Drop Testing Machine is used to measure the dropping impact incidence when the package in using, transportation and decorating. Labtone "1G+" project strictly ensure the accuracy. Besides precision plane drop testing, it also can undertake edge and angle test to ensure the complete performance evaluation for the package. During the products handling or transport process, there may be drop/ fall, which results in damage within the products. And this Drop Tester simulates the drop/ fall of a finished product to evaluate the damage. All the rhombohedrons, angles and faces of the products can be tested.
-
product
Small Objective Drop Tester
KD-208
King Design Industrial Co., Ltd.
Testing of Mobile phones, batteries, PDA, digital camera and other hand-held communications and IT product.
-
product
Drop Testing Machines
Infinity Machine International Inc.
Drop Testing Machines by Infinity Machine International Inc. - for applications such as: tumble tester, drop weight impact testing machine, mobile phone roll drop tester, micro drop testing machine for mobile phone, and more.
-
product
Millivolt Drop Tester
The SCR ELEKTRONIKS Millivolt Drop Tester is an industry acclaimed product. MVDT has a specially built constant current source (current generator) up to 400A (depending on model) and a dedicated PLC to store test parameters (in automatic models), perform test procedure, make the millivolt drop & junction resistance measurements and store test results, that can be retrieved later or downloaded to PC. PC based TestWare can display the test results & export those to Office, HTML, Printer or PDF. The manual models consist of the constant current source, digital ammeter and a digital millivolt meter with 3 ranges.
-
product
Spinning Drop Tensiometer
SDT
Our Spinning Drop Tensiometer – SDT measures interfacial tension with a high degree of accuracy and a particularly wide measuring range. The SDT is the ideal solution for the quality control and development of emulsions and surfactants thanks to its enormous bandwidth, small sample volumes and simple handling during preparation.
-
product
Zero-distance Drop Test System
KRD40 series
KRD40 series drop tester, mainly simulates the resistance to drop and impact of large and heavy packaging products. Its strong power system and unique sample holder facilitate easy loading and unloading of oversized and overweight items and automatically rise to the setting. After the height, the drop test is completed. It can realize the drop test of the edge, surface and angle of the sample. This equipment is mainly used to evaluate the ability of product or packaging to withstand drops during transportation and loading and unloading, so as to improve product and packaging design.
-
product
Small Drop Test System
KRD41 series
KRD41 series small drop tester is suitable for free-fall test of small consumer electronics and components such as mobile phones, walkie-talkies, electronic dictionaries, CD / MD / MP3 and so on, applicable standards JISC 0044 and IEC 60068-2-32. Through standard tests on electronic products (surface drop, corner drop, edge drop, etc.) and collecting data, it simulates the vertical drop impact of electronic products during transportation and handling. It provides a basis for the design of the product's buffer and vibration damping and the selection of structural materials.
-
product
RF Volt Meters
The latest addition to Boonton’s popular 9200 series of RF voltmeters. It combines accuracy, smart probes, and operator features that have never before been available in its price range.
-
product
Transducers with 0-10 Volts Output
Overview of transducers with 0-10V output for temperature, humidity, CO2 and pressure.
-
product
Air-arm-type Drop
KD-128A
King Design Industrial Co., Ltd.
All new developing products must undergo several strict testing processes while in designing, manufacturing and packing/ shipping even. Our drop tester will provide data digitizing and analyzing of your drop and striking while the products in transportation. The testing data will help you improve the packing and buffer materials.Packaged drop test is applied to test the anti-vibration & covering capability of packaging material and the sufficiency of product’s impact-resisting capability reg...show more -
product
High-Voltage Amplifiers - to 1000 Volts peak-to-peak
These amplifiers provide high amplitudes and bandwidths, and are well suited for use as booster amplifiers for lower-voltage arbitrary waveform generators.
