Signal Conditioning
The processing of signals to reduce noise level, amplify, attenuate, or otherwise condition.
See Also: Signal, Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Generators, Signal Meters, Signal Conditioners
-
Product
Multichannel Signal Generator for DOCSIS 3.1 Downstream & Upstream
CLGD DOCSIS
-
The R&S®CLGD is a multichannel signal generator for simulating a cable TV network with full channel loading. It generates broadband data signals for DOCSIS 3.1 as well as digital and analog TV channels. Signals can be freely combined in the downstream or upstream, allowing users to simulate any conceivable channel loading scenario in the lab.
-
Product
Signal Amplifier
9400
-
Model 9400 was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It has four channels built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
Product
Signal Integration Systems
Avenue
-
The Avenue system includes modules for video up/down conversion, audio embedding, synchronization, conversion, routing, noise reduction, protection switches, test signal generators and more. Avenue signal processing modules are used worldwide in broadcast, mobile, satellite, cable, worship and post production facilities. Avenue is a tray-based signal integration system housed in a 1RU or 3RU frame. Any combination of 1.5 Gb/s HD, 3 Gb/s HD, SD, MPEG, analog video and audio processing modules can be used together in the same frame.
-
Product
Electronics For Signal Processing
-
PCB Piezotronics manufactures a wide variety of electronics to power ICP®, PE (Charge Mode), MEMS, strain gage and other types of sensors. All of these products provide conditioning of sensor signals for transmission to data acquisition systems.
-
Product
Digital Signal Processor Card for PCI bus
SI-C33DSP
-
The SI-C33DSP-PCI from Sheldon Instruments is a powerful Digital Signal Processor (DSP) card for your PC equipped with a PCI bus. It is based on Texas Instruments’ new 150Mhz TMS320VC33, 32 bit floating point DSP, and can transform your PC into an ultra high performance development system and DSP accelerator.
-
Product
Signal Generator
ZET 7192
-
*Analogue two-channels generator*Random profile signal formation*CAN 2.0 data interface
-
Product
Signal Integrity Test Products
RoBAT SCARA-TDR-M
-
*Fully automatic TDR tester for bare and assembled PCBs*2 – 24 Port Ultra-compact TDR units*Full range of TDR tests and measurements available*100% test in a production environment*Custom modules with automatic tool changer
-
Product
RF Signal Strength Meter
006
-
Hand Held RF Signal Strength Meter. Detects RF Activity around centre frequency. Available for 315MHz, 433MHz, 868MHz, 869.85MHz, 914.5MHz.
-
-
Product
Signal Relays
-
Panasonic Industrial Devices Sales Company of America
Mechanical Relay ideal for signal control, etc., with less than 2A nominal switching capacity. Low Level current switching below 2A. Features include gold contacts, stable contact resistance, fully sealed construction, Form C contact arrangement, available latching and low operating power, and compact size for optimal board space usage. Applications include: AC Control, Communications, Security, Measurement Equipment, Audio Visual Devices, and Automotive.
-
Product
High-Frequency Signal Amplifier
VCH-605
-
High-frequency signal amplifier VCH-605 is designed to amplify and multiply sinusoidal signals with a frequency of 1-100 MHz.
-
Product
Digital TV signal analyzer
1750QAM
-
DIGITAL TV SIGNAL ANALYZER 1750QAM? The very excellent signal analyzers of choice for field testing of QAM digital signals on your CABLE-TV SYSTEM.They demodulate and accurately measure the QAM signals carried through the cable system.They provide the measurement power the field technicians need for the latest 64-256QAM digital technologies and are very simple to use, measuring SNR(MER), EVM, Pre-BER, Post-BER, Constellation Diagram.
-
Product
PC Oscilloscopes & Mixed Signal Oscilloscopes
PicoScope® 3000 Series
-
PicoScope 3000 Series USB-powered PC oscilloscopes are small, light, and portable and can easily slip into a laptop bag while offering a range of high-performance specifications.
-
Product
Video Signal Generator
MSHG-800Plus
-
MSHG-800Plus construct HDMI 2.0(HDCP 2.2) 4Port, HDMI 1.4 & MHL 2.0 1Port - HDMI 2.0 (HDCP 2.2) supports 4Ports - HDMI 1.4 (HDCP 1.4) & MHL 2.0 supports 1Port - 4 Ports ARC functions supports - RS-232C Control supports - Each outputs status with front LED button - Button locking function - Easy upgrade / update to USB memory stick
-
Product
Radio Monitoring and Signal Analysis
-
Shoghi has a full portfolio of products which fulfill the customer requirements for radio monitoring and signal analysis. Shoghi has a very robust SDR based wideband radio monitoring solution which can be implemented both in static or mobile versions for HF and VHF/UHF frequency bands. The Shoghi Radio Monitoring and DF system is the full-fledged product which provides the facilities for wideband signal reception and advanced signal analysis capabilities in addition to both wideband and narrowband D capabilities. The signal analysis capabilities include the ability to demodulate and decode both narrowband and wideband signals and advanced signal protocol analysis for detection of specific data protocols used in the intercepted RF signals.
-
Product
Signal Converters & Load Cell Signal Converter
-
Mantracourt provide a range of signal converter modules which take load cell or strain bridge inputs and provide a data output in a variety of bus and protocol formats. Hardware formats include RS232, RS422 RS485, CAN and USB. Signal converter protocols include Industry Standards such as MODBUS, or Mantracourt’s own proprietary protocols which have been optimised for either ease of use (MantraASCII2) or higher speed communications (MantraBus2).
-
Product
Digital And Mixed Signal Oscilloscope
MSO/DPO70000 Series
-
The MSO/DPO70000 is one of the most advanced oscilloscopes in its class: enabling today’s engineer to see signals better with minimal noise, debug signal anomalies faster, reduce debug time, and utilize measurement and analysis tools for automated compliance testing and other verifications. In addition, the MSO/DPO70000 is perfect for analog/digital design and debug, data communications and high-speed serial communications. See how you can use the MSO/DPO70000 for your next project to find and analyze a wide range of mixed-signal anomalies.
-
Product
Signal Processor Board
MS 1532
-
- Frequency coverage from 5 kHz to 30 MHz in 1-Hz steps- High dynamic range: +30 dBm 3rd-order intercept typical- Digital filtering provides 58 IFBWs from 56 Hz to 8.0 kHz with exceptional shape factors- AM, Synchronous AM, FM, CW, USB, LSB & ISB detection modes standard- Tunable notch filter- Fast, flexible scanning with 100 memory channels- Large readable LED displays & user-friendly controls- Noise blanking & pass band tuning- Internal switchable preamplifier & attenuator- Operator-selectable RS-232, RS-485, or- RS-422 remote control- Viretx 5 FPGA based design (Two virtex for image processing)- LPC2468 ARM 7 Processor based design- MIL1553B and RS485 Interface- Two High speed 14 bit ADC (125MSPS) for I & Q Sampling- Direct sampling 2-30MHz- Audio CODEC- Conduction Cooled Board
-
Product
Wireless Camera Detector / RF Signal Detector
SH-055SV / 10127
-
"This RF Signal Detector / Wireless Camera Detector / Cellular Phone Detector / Bug Detector" can detect the popular wireless CCTV camera, wireless phone, wireless tap and Cellular phone from 50 MHz ~ 6.0 GHz
-
Product
Handheld Signal Generator
MK4
-
9 signal type and power presets, 3 per Band (B1, B2, B3) 3 power output presets, Single signal preset, 2 or 3 signal preset cycling, CW or Preset List Sweep.
-
-
Product
SD-SDI Test Signal Generator
7750TG
-
The 7750TG Test Signal Generator provides a cost effective method of generating SDTV 270Mb/s test signals. The 7750TG is ideal for checking signal path integrity, monitor alignment or to determine system performance over varying cable lengths. The 7750TG generates test signals in 525 line and 625 line SMPTE 259M-C video formats and offers four 270Mb/s outputs.
-
Product
Signal Conditioners
-
Metrix* proximity signal conditioners are used with existing drivers. They power the driver and scale the 4-20 mA output.
-
Product
Optical signal transmission
Digital
-
The fibre optic cable are used to transmit digital signals from the device under test under EFT/burst interference.
-
Product
Head Mount Signal Conditioners
-
Head mount signal conditioners are designed to mount in industrial protection heads for use with thermowells. The sensors are small sized and offered in a variety of input and transmission options.
-
Product
Condition Based Monitoring
-
Test Products International, Inc.
Vibration analysis at the touch of a button. Overall machine and bearing conditions: vibration values are displayed with color coded alarm levels for ISO values and Bearing Damage (BDU).
-
Product
Signal Spectrum Converters
-
Advanced Science and Novel Technology, Co., Inc.
DC to 5.6GHz finite impulse response filter.Two differential CML-type input ports and one differential CML-type output port.Nine analog tap-weight control inputs.Differential gain of approximately 0dB.Single +3.3V or -3.3V power supply.Power consumption: 422mW.Fabricated in SiGe for high performance, yield, and reliability.Custom CQFP 44-pin package.
-
Product
Car-to-X Signal Strength Emulator
-
Qosmotec Software Solutions GmbH
QPER-C2X is a special adaptation of the signal strength emulator QPER, designed for mobile and Vehicular Ad-hoc Networks (MANet and VANet). Every radio devices in such an infrastructure-less network acts as a sender, receiver, and forwarder (router). Therefore, the ports of the QPER-C2X hardware are fully connected with each other by dynamically controllable attenuators. The system is fully designed for frequencies up to 6 GHz, since wireless communication for Intelligent Transport Systems (ITS) is based on the WLAN standard IEE 802.11p from 5.850 MHz to 5.925 MHz. The connected ITS stations can be either on-board units, as they are built into cars, or road side units that are used by road infrastructure (traffic lights, road work area delimiters, velocity signs). For tests in the lab, radio modules of such ITS stations are each kept in a shielding box that prevents any unwanted radiation over the air.
-
Product
RF Signal Generators
-
The RF signal source mainly acts as a stable local oscillator signal in the test, or generates various types of modulated signals, and the two-tone signal is used for signal excitation, receiving sensitivity testing and other applications. When choosing the RF signal source, the frequency range of the signal output, power requirement size, modulation type, frequency stability, amplitude accuracy and many other factors needs to be considered.
-
Product
Signal Routing Software
Switch Path Manager
-
Our signal routing software, Switch Path Manager, simplifies signal routing through switching systems and speeds up the development of switching system software. Switch Path Manager supports Pickering''s switching modules and the interconnection between these products. Third-party products can be supported upon request. Once a switching system model has been created, simply defining the endpoints that are required to be connected together can perform signal routing. The ability to automate signal routing results in effective and easy switching system managementsafely and quickly.
