Exposure
-
-
Product
Vehicle Electromagnetic Field Exposure Test System
SEM-400
-
Beijing KeHuan Century EMC Technology Co,.LTD
Vehicles are our daily public transportation. Electromagnetic pollution in vehicles has attracted more and more public attention. The newly revised compulsory standard GB27630-201X "Passenger Car Air Quality Evaluation Standard" intends to require the electromagnetic field in the car as one of the indicators, according to GB/T37130-2018 "Measurement method of vehicle electromagnetic field relative to human exposure" The measurement method is to measure the intensity of the magnetic field in the car. In the frequency range of 10Hz-400kHz, the electromagnetic field measurement result should meet the public limit requirements of GB8702-2014 for electromagnetic exposure.
-
Product
Outdoor Exposure Tester
OET
-
A comprehensive analysis of PV modules includes many different parameters. Determining the normal module operating temperature (NMOT), incidence angle effects and comparing soiling effects on different modules up to the initial degradation of PV modules are all parameters that can be analyzed with our outdoor exposure tester. The tester comes with up to twelve electronic loads installed in a 19" rack. The loads have two main functions: maximum power point tracking (MPPT) and IV curve tracing. For the advanced analysis, it is possible to change between these two modes within one test. In the normal operation mode, the electronic load keeps the module under MPP and each predefined interval an IV curve is traced. The entire tester comes with all necessary sensors such as temperature sensor, which can be attached to the module to determine the NMOT temperature like defined in IEC 61215 (MQT 05) and IEC 61853-2. The irradiation sensor is also included. In combination with our tracking system P2, it is also possible to determine incident angle effects of the PV module. It is also possible to connect other irradiation sensors for diffuse and direct irradiation, which helps to understand the behavior of the module in different irradiation conditions. An optional albedo meter is a powerful tool for the analysis of bifacial modules. The entire graphical user interface is web based and offers the possibility to access the system from the all computers in the network.
-
-
Product
Human Exposure Measurements to Luminaries
-
Through different ways of coupling between luminaries and humans, a level of exposure of a person to electromagnetic fields can be derived. One part of the exposure is based on capacitive coupling between lighting equipment and person. This creates induced internal electric field that must be evaluated using an EMI receiver and a Van Der Hoofden test head.
-
Product
*High Power Measurement From Short Exposure
-
Ophir has a number of ways to measure high laser powers up to 12kW without heavy water cooled equipment. Most of today’s lasers can be set to emit for a short, precisely controlled period of time. If a short exposure to the laser of 0.3 – 10s is sufficient to measure the power then there are compact, uncooled sensors available for this purpose.
-
Product
LITHOSCALE® Maskless Exposure Lithography Systems
-
Maskless exposure lithography systems represent an entirely new product platform of EVG lithography equipment.
-
Product
Stability Test Chamber
-
Wewon Environmental Chambers Co, Ltd.
Test Instrument to simulate effects of weathering conditions, e.g. UV light exposure and water exposure, on samples to conveniently predict the relative durability of a sample, e.g. paint, surface coatings, plastic and related materials.
-
Product
Vibration Meters
-
Companies must comply with the Control of Vibration at Work Regulations 2005 – this requires them to minimise and monitor exposure to hand-arm vibration and make sure that it does not exceed set levels and cause Hand Arm Vibration Syndrome. The best way to do this is by using a hand-arm vibration meter.
-
Product
5MP MIPI Camera Module
E-CAM55_CUMI0521_MOD
-
e-CAM55_CUMI0521_MOD is a small form factor, 5 MP fixed focus camera module based on AR0521 CMOS image sensor from ON Semiconductor® has a dedicated, high-performance Image Signal Processor chip (ISP) on-board that performs all the Auto functions (Auto White Balance, Auto Exposure control) in addition to complete image signal processing pipeline that provides best-in-class images and video. This low light camera module can stream uncompressed VGA (640 x 480) at 75 fps, HD (1280 x 720) at 100 fps, 1280 x 960 at 75 fps, FHD (1920 x 1080) at 65 fps, 2560 x 1440 at 38fps, 2592 x 1944 at 28 fps.
-
Product
UV Exposure Sources
-
Standard maintenance, lamp, or filter replacement, does not require any tools. Locking indicator dials on all the system controls, located together for ease of alignment, provide for a reproducible setup. A beam imaging accessory makes alignment even faster.
-
Product
Noise Dosimeters
Spark Family
-
Spark® series dosimeters are compact, affordable and tamper-proof personal Noise Dosimeter that measures the following to applicable IEC and ANSI standards:*Noise Exposure: Multiple Dose; Projected Dose; Time Weighted Average; (all with 4 user selectable combinations of Exchange Rate, Threshold, Criterion Level and Criterion Time); Sound Exposure Level*Sound Levels:; Leq; Lmax; Lmin; Lpeak/Luwpk, SEL and more*Time and number of events above Ceiling Level (115 dB) and Peak Level (140dB)
-
Product
Conductive Emission Measurement
-
Holland Shielding Systems B.V.
On site testing for exposure limits in working conditions to any international standard. This involve pacemakers and HSE Heath and safety executive, invitarisations worldwide.
-
Product
Beam Directional Power Supply Battery 40 to 160 kV
CP160B
-
Next to the CP120B, the CP160B is the slightly more powerful version of our ultra-light, compact and battery operated constant potential portable X-Ray generators. Allowing penetration reaching up to 30 mm for steel, the CP160B is the perfect tool for specific NDT applications that require repetitive short exposures, as well as security applications.
-
Product
Radiometers
-
UV Intensity Meters & Visible Intensity Meter for Light Curing Systems. Dymax UV and visible radiometers are simple to operate and allow operators to monitor and document a UV/Visible light curing process. A low UV/Visible intensity measurement signals an operator to replace the bulb, reflector, or lightguide. Radiometers can also be used to confirm that operators are properly shielded from UV/Visible exposure. Degradation of curing bulbs, lightguides, and reflectors can decrease intensity, resulting in incomplete cures.
-
Product
Lithography
-
EVG’s key competencies in lithographic technology lie in the high-throughput contact and proximity exposure capabilities of its mask aligners and its newly developed, revolutionary and highly versatile maskless exposure lithography systems. These capabilities are complemented by its resist coating and resist development systems with advanced in-house process competences and hands-on development skills.
-
Product
Rugged
-
Advantech industrial monitors are built to withstand operation in industrial environments, extreme temperatures, and exposure to corrosive substances
-
Product
Rain Test Chamber
-
Xi'an LIB Environmental Simulation Industry
Simulates real-world rain exposure to test the waterproofing and weather resistance of products.
-
Product
Area Monitors
-
Provides real-time remote radiological monitoring. Local readout of hand-held meter allows for use as a portable survey instrument. More importantly, since the probe’s sensitive electronics are located far from the high field (25 to 350 feet away), they are not subject to destructive gamma exposure. The probe head may be placed directly into a filter compartment or against a resin tank or waste liner.
-
Product
Sound Level Meter
SoundTrack LxT
-
The SoundTrack LxT® Sound Level Meter was developed to meet the unique needs of those involved in workplace noise exposure assessment and plant noise surveys.
-
Product
IP67 Testing
-
IP67 is an electronics and sealed device attribute requirement with a physical no-water ingress testing process used to determine whether components meet the requirements needed to receive an IP (ingress protection) rating. Devices with this internationally recognized rating resist exposure to dust and withstand up to 30 minutes of submersion in water up to 40 inches (1 meter) in depth. Products assigned an IP67 rating are typically used in outdoor applications or other environments requiring resistance to dust, moisture, and water submersion.
-
Product
Xenon Lamp Weathering Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood , a 23 years of Bench-top Xenon Lamp Test Chamber, Bench-top Xenon lamp aging test chamber, Bench-top xenon lamp weathering test chamber ,Xenon Lamp Test Chamber, Xenon Test Chamber manufacturers Small, simple and economic xenon test chamber. It uses a low power air-cooling xenon lamp to produce enough big irradiance energy in a small space. Moreover, through a special catoptrical system to ensure every exposure sample get the homogeneous irradiance distribution.
-
Product
Xenotest Beta+
-
Atlas Material Testing Solutions
The Xenotest Beta+ is a premium stand-alone rotating rack xenon instrument with 4000cm2 exposure area. It comes with a complete set of parameter controls.
-
Product
2MP Sony STARVIS IMX290 Ultra-low Light Jetson TX2 Camera
E-CAM21_CUTX2
-
e-CAM21_CUTX2 is a 2MP Ultra-Lowlight 4-lane MIPI CSI-2 camera board for NVIDIA® Jetson TX2 developer kit. This camera is based on 1/2.8" SONY IMX290 CMOS Sensor, one of the most popular Sony's STARVIS® sensor. Its effective pixel back-illuminated technology with improved sensitivity in the visible-light and near infrared light enables customers to capture images even in absolute darkness. This Starlight Camera uses NVIDIA® on-board Jetson TX2 Image Signal Processor (ISP) to perform all the Auto functions (Auto White Balance, Auto Exposure control) and significantly, improved image quality. It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement.
-
Product
RF Safety Monitoring
MVG EME Guard Plus
-
The EME Guard Plus is designed to record EMF exposure near antennas while continuously monitoring potential over-exposure. Lighter than the previous model, the EME Gaurd Plus makes it easier for workers to wear on the job. The longer battery life and extended memory capacity enable more measurements to be recorded.
-
Product
Real-time 1/1, 1/3 Octave Analysis Software
DS-0323
-
This software analyzes the 1/1 and 1/3 octave bands for 2 - 32 channels (2 - 64 channels when two units are connected ) in real-time from 0.5 to 20 kHz. The filter is compatible with the IEC, JIS, and ANSI standards. The equivalent continuous A-weighted sound pressure level (Laeq) and the single-shot sound exposure level (Lae) are calculated simultaneously by setting measurement time. Variations in level (time series) for each band can be saved for up to 2,000 points.
-
Product
Relative Humidity Logger Sensor
NUL-207
-
This sensor measures relative humidity. It can find use in recording variations with weather conditions and the relative humidity effect on organisms such as seedlings and insects. It is located in a plastic box with exposure of the sensor being through a hole in the side.
-
Product
Control Unit for SITEx & SITExs
SITEX SCU286
-
The SCU286 has a system for direct measurement of the high voltage delivered by the X-Ray generator to guarantee the accuracy of the radiological parameters. Based on this data the control system maintains the stability of mA and kilovolts to within ± 0.5% in any selection range.SITEX & XS units offer a totally constant quality of exposures, as they are virtually exempt from fluctuations in the power supply.
-
Product
X-ray Non-Destructive Testing (NDT) System
DynamIx HR / Series 5
-
High precision 12-bit 50µm reading allows inspection of minute image details. Wide dynamic range resulting in wide allowance of X-ray exposure value.
-
Product
Linear Array
-
Linear array sensors consist of a linear array of integrating photosensing pixels which measure incident light over a user-defined exposure time and generate a voltage or digital output which represents the light exposure at each pixel. The sensors are available in a variety of lengths and pixel resolutions. The analog output may be directly interfaced to an ADC for digital processing or for comparing black/white thresholds. Applications include contact image sensing, optical character recognition, edge detection, and object measurement in products such as copiers, document scanners and spectroscopy.
