- Pickering Interfaces Inc.
product
PXI Amplifier And Attenuator Modules
Pickering's PXI Amplifier and Attenuator Modules include our accurate DC to 3GHz programmable attenuator has a 1dB step resolution, allowing it to adjust signal amplitudes for optimum measurement by other devices. The other programmable attenuator available has a bandwidth between 10MHz and 6GHz available in triple or hex formats.
-
product
YDFA Amplifier
a high-gain three staged polarization maintaining optical amplifier unit designed for applications requiring high efficiency optical amplification in the 1060 nm regime in both CW and pulse mode operations.
-
product
Non-Linear Pulse Amplifiers
These amplifiers have fixed output amplitudes, and are DC-coupled. All models can drive 50 Ohms or higher.
-
product
Non-Programmable Signal Conditioning
7525
The Dynamics 7525 Differential Amplifier was designed for use in high-speed data systems. It is completely compatible with all tape recorders for direct recording and is also useful for isolating digital or high-speed impulse signals when you cannot afford to reconstruct the signal or change pulse characteristics.
-
product
Phase Noise Measurement Solution, 50 kHz to 110 GHz
E5505A
The Keysight Technologies E5500 Series of phase noise measurement solutions offers the most flexible set of measurements on one-port VCOs, DROs, crystal oscillators and synthesizers. Two-port devices, including amplifiers and converters, plus CW, pulsed and spurious signals can also be measured. The E5500 measurements include absolute and residual phase noises, AM noise, and low-level spurious signals. The stand-alone instrument architecture easily configures for various measurement techniques, including the PLL/reference source technique, residual and FM discriminator methods.
-
product
*Pulse Characterization Sensors
Pulse Characterization Sensors provide the ability to see and measure the temporal characteristics of pulsed and CW laser beams. Ophir Fast Photodiode Detectors are designed to convert optical signals into electrical signals which are then measured with third-party instrumentation such as oscilloscopes and spectrum analyzers. Accessories are available to connect to IS6 integrating spheres or fiber optic cables. Attenuating filter accessories are also available to increase their dynamic range. Di...show more -
product
VME PWM Servo Motor Driver / Amplifier Board
64PW2
NAI’s 64PW2 is a 6U VME Servo Motor Driver/Amplifier Board featuring a dual, four-quadrant, bi-directional, PWM servo amplifier. Specifically targeted for DC servo motor applications, this board has an amplified power stage that uses a Pulse Width Modulation (PWM) control signal to provide motor control for both brush and brushless motors. Each motor drive accepts a 65 VDC power input and provides a 5 Amp maximum continuous current output (8.5 Amp peak).
-
product
Tunable, Ultrafast TI: Sapphire Laser
SPRITE XT
Sprite XT is a flexible ultrafast, femtosecond laser source. It delivers stability, reliability and productivity and is equally at home in the lab or as part of an OEM application. Choose your output power (up to multi-Watts), pulse width (femtosecond or picosecond models), wavelength range (fixed wavelength or tunable), and pulse repetition rate (<80 MHz to multi-GHz). All Sprite models are designed for alignment-free and maintenance-free operation and can be controlled from a web browser. It’s ideal for multi-photon excitation (MPE) and FLIM, quantum optics, time resolved spectroscopy, nonlinear optics, pump-probe experiments, microscopy, amplifier seeding, and electro-optic sampling.
-
product
Broadband Power Amplifier
Panda Microwave design, manufacture, and support a wide variety of Power Amplifier. RF amplifiers product line from Panda Microwave consists of low noise amplifiers, Power Amplifier Module and Solid State High Power Amplifier. Our Power amplifiers cover frequency range from 100MHz to 50GHz and used Thin-film Technology. Our low noise amplifiers have superior noise figure numbers and a variety of models. Gain block low noise amplifiers provide all around gain where noise is not critical. High power amplifiers system equipment is available with either manual or digital control interfaces, power capacities up to 100W pulse power.
-
product
RF Amplifiers up to 1000 MHz
Narrow and Broad band high power RF modules and rack mount amplifier systems using solid state devices including LDMOS and GaAs in Class A and Class A/B topologies for Pulse, AM, FM, continuous wave and digital modulation applications that include EW, Radar, Jamming, EMI and EMC radiated immunity, and wireless communications testing.
-
product
Power Sensors
RTP5518
Providing the highest video bandwidth and fastest rise times, the 50 MHz to 18 GHz Power Sensor by Boonton is the ideal instrument for fast, accurate and reliable RF power measurements. This module is ideal for many different applications including Crest Factor and Peak to Average Power Ratio (PAPR) measurements for Power Amplifiers and RF components; Telecommunication & Satellite signals: W-CDMA, QAM, OFDM, LTE-FDD and LTE-TDD; WiFi signals: 802.11ac and legacy 802.11 a/g/n/b; RF and Microw...show more -
product
SSPAs / LNAs / Broadband
SSPAs based on the latest Galium Nitride (GaN) technology offer the best combination of high peak powers, high reliability, high efficiency, and soft degradation. High efficiency and high power are hallmarks of GaN technology, enabling SSPAs to challenge traditional tube-based amplifiers across the design spectrum. In addition the long lifetime from these devices, combined with the gradual degradation should individual devices fail, provide unparalleled service lifetime. Techniques such as bias modulation and linearization provide even better prime-power efficiency while still meeting the demanding requirements of pulsed or CW applications.
-
product
Field Strength Meter
FIM-71 VHF
The Model FIM-71 is a portable, laboratory quality Field Strength Meter designed for rigorous field applications. Combining a calibrated half-wave dipole antenna and a highly accurate tuned voltmeter with a range of 140 dB, the FIM-71 is suitable for practically all types of RF emission measurements in the 45 MHz to 225 MHz spectrum. The operator can switch select wide or narrow bandwidth, peak or average value of TV or pulse modulated signals, AM or FM demodulation, and a meter dynamic range of...show more -
product
Instrumentation HPAs
Communications & Power Industries
CPI SMP Division provides a complete line of high-powered continuous wave (CW) and pulsed instrumentation amplifiers for EMC testing, available in octave and multi-octave bandwidths from 1.0 GHz to 95.0 GHz and power levels exceeding 2.0 kW to meet the new military and automotive standards. CPI is the only supplier that manufactures both the traveling wave tube (TWT) and the TWT amplifier.
-
product
Cable Diagnosis System
Baseline 9400 TDR/ICE
K&S Engineering and Scientific Ltd
BASELINE 9400 TDR/ICE - the unique cable diagnostic system: - A state-of-the art cable fault locating instrument containing a high speed data recorder, capable of capturing and evaluating 40 million samples of electrical data per second, while also featuring amplifiers, attenuators and an adjustable pulse generator.
-
product
Pulsed Injection-Locked IMPATT Amplifiers
Pulsed ESR/EPR
Insight Product Company offers pulse injection-locked IMPATT amplifiers for pulse ESR/EPR experiments. Pulsed injection-locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate the amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
product
PNA Network Analyzers
The PNA Series of network analyzers offers industry-leading performance for testing amplifiers, mixers, and frequency converters. Built-in pulse modulators and pulse generators provide pulsed S-parameter measurements quickly and accurately. All models are available in two-port single-source and four-port dual-source versions.
-
product
Pulsed ESR/EPR: Pulsed Injection-locked IMPATT Amplifiers
Insight Product Company offers pulse injection-locked IMPATT amplifiers for pulse ESR/EPR experiments. Pulsed injection-locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate the amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
product
6-Channel VME Pulse Amplifier
V860
The V860 is a multichannel pulse amplifier packaged as a standard VME module. It accepts logic-level inputs and generates high-level, very fast positive output pulses.
-
product
Semiconductor Optical Amplifier
SOA
Amonics SOA is a polarization maintaining optical amplifier with high fiber-to-fiber gain. It is designed for transmitter applications to increase optical launch power to compensate for the loss of other optical devices. The benchtop version incorporates a user-friendly front panel housing a LCD monitor display, key switch, power control knob and optical connectors. RS232 computer interface is also equipped on the rear panel. 1MHz with 10ns pulse width intensity modulation is available. The OEM module version is an ideal building block for OEM system integration, especially in optical communication network and CATV applications. It requires only a single +5V power supply.
-
product
Amplifiers
The amplifier is one of the most important components in a pulse processing system for applications in counting, timing, or pulse amplitude (energy) spectroscopy, providing the pulse-shaping controls needed to optimize the performance of the analog electronics.
-
product
PNA-X Network Analyzers
Keysight's PNA-X is more than just a vector network analyzer. It is the world’s most integrated and flexible microwave test engine for measuring amplifiers, mixers, frequency converters, and other active devices. The hardware includes two internal signal sources, a signal combiner, S-parameter and noise receivers, pulse modulators and generators, and a flexible set of switches and RF access points. These hardware features provide a powerful core for a broad range of linear and nonlinear measurements, all with a single set of connections to your device under test.
-
product
PXI Source/Measure Unit
Keysight PXI source/measure unit (SMU) offers high-throughput and measurement quality for design validation and production test of RF power amplifiers. It delivers industry-leading output stability under extreme, dynamic load conditions and unmatched transient performance to dramatically reduce voltage droop due to pulse loading for faster test time.
-
product
Power Sensors
RTP5006
Providing the highest video bandwidth and fastest rise times, the 50 MHz to 6 GHz Power Sensor by Boonton is the ideal instrument for fast, accurate and reliable RF power measurements.This module is ideal for many different applications including Crest Factor and Peak to Average Power Ratio (PAPR) measurements for Power Amplifiers and RF components; Telecommunication & Satellite signals: W-CDMA, QAM, OFDM, LTE-FDD and LTE-TDD; WiFi signals: 802.11ac and legacy 802.11 a/g/n/b; RF and Microwav...show more -
product
RF Amplifiers up to 2500 MHz
L and S Band 1,2,4, and 8 Kilowatt rack mount solid state microwave amplifiers ideal for CW and pulse TWT amplifier replacement utilizing GaN technology and rivals the TWT amplifier in size and weight. Also available is our broad line of high power modules including 25, 50, and 100 watt pallets for integrating into your own power amplifier design.
-
product
CEP Stable Lasers And CEP Phase Stabilization
Carrier envelope phase stabilization (CEP) is an enabling technology for metrology and for the generation of few cycle pulses. As one of the pioneers in the field we have developed products that allow to stabilize the carrier envelope phase of light pulses of few cycle pulse oscillators and amplifiers.
-
product
2-18GHz Digitising Receiver
DR068-M1
Teledyne Defence & Space (TDS) DR068-M1 Digitising Receiver combines a state of the art broadband frequency measurement receiver with a high dynamic range successive detection log video amplifier to realise a high probability of intercept receiver. Digital signal processing techniques are utitlised to derive pulse parameters which are packaged into a PDW and transferred via a low latency Gigabit Ethernet interface. The DR068-M1 enables new and existing systems to incorporate a wideband high POI pulse detection capability with minimal integrating effort.
-
product
High Energy Laser Systems
APL2100 Series
APL2100 series amplifiers are designed to produce up to 1000 mJ picosecond pulses. High pulse energy, excellent pulseto- pulse energy stability, superior beam quality makes APL2100 series picosecond amplifiers well suited for applications like OPCPA pumping, non-linear optics and others.
-
product
Field Strength Meter
FIM-72A UHF
The Model FIM-72A is a portable, laboratory quality Field Strength Meter designed for rigorous field applications. Combining a calibrated half-wave dipole antenna and a highly accurate tuned voltmeter with a range of 140 dB, the FIM-72A is suitable for practically all types of RF emission measurements in the 450 MHz to 960 MHz spectrum. The operator can switch select wide or narrow bandwidth, peak or average value of TV or pulse modulated signals, AM or FM demodulation, and meter dynamic range o...show more -
product
SHOCK TESTER
King Design Industrial Co., Ltd.
*Shock amplifier is mainly used to small object, and can reach the pulse duration and high acceleration that shock table couldn’t achieve.*Equipped with shock table or different shock module (the theory is to amplify impact energy through second impact), shock amplifier can reach the requirement of high acceleration.
-
product
TWTs - Traveling Wave Tubes
Travelling wave tubes remains a valuable type of amplifier for high output power in the microwave range. Its main advantages are of high output power, big bandwidth-duration and reliability. Insight Product Co. offers TWT packaged tubes providing output power from tens to several hundred watt in a continuous mode and to 1.5-2.0 kw in a pulse mode, and frequency bandwidth of 1.5 octaves. TWT applications include satelite communications (transponders) both on land and on satelite installations, radio relay communication lines, electromagnetic compatability (EMC) testing industry for immunity testing of electronic devices, and radars (maritime, weather, airplanes, land).
