-
Product
Isolated Analog Expansion Board
MSXB 085
-
The MSXB 085 Isolated Analog Expansion Board provides isolated analog inputs and isolated analog outputs for DAP systems. Use these boards to eliminate ground currents – a potential source of noise in your measurement and control signals – and eliminate timing skew.
-
Product
Analog Oscilloscope
PS-355
-
*HOLD-OFF, X-Y OPERATION.*1mV/DIV SENSITIVITY.*10nS/DIV RESOLUTION.*COMPONENT TESTER.*BEAM-FINDER, ILLUMINATE.*WITH DELAY SWEEP.*TWO SWEEP MIX FUNCTION.*CE, TUV GS, UL CUL, IEC1010
-
Product
Terminal Equipment Simulator
AI-5620
-
The AI-5620 simulates a single port two wire analog TE (Terminal Equipment) or CPE (Customer Premise Equipment) device. It is designed to measure and analyze signals generated by a CO (central office) line card, VoIP terminal adapter FXS port, or any device utilizing a SLIC (subscriber line interface circuit).
-
Product
Dual-Axis Accelerometer For HS3/4/4-DIFF Handyscopes, +/- 16G
TP-ACC160-25
-
The Accelerometer is a low cost, low power, complete dual-axis accelerometer with signal conditioned voltage outputs. The output signals are analog voltage proportional to acceleration. The Accelerometer is capable of measuring both positive and negative accelerations to at least +/- 16G.
-
Product
LXI Reed Relay Matrix - Single 32x16 Plugin, Direct Y Access, 3 Analog Buses
65-225-002
-
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
Product
Compact Low Profile Load Cell
1000 Series
-
Compact Low Profile load cells are fully stainless steel, hermetically sealed load cells with a multi-beam internal structure, and fully integrated electronics to provide high level analog or digital outputs. This type of load cell is easy to use for measuring tension or compression loads from 200N (50lb) to 5kN (1000 lb), and is capable of rejecting side forces that would otherwise affect accuracy. This type also offers the user the ability to set the gain and offset (span and zero) electronically, to provide maximum flexibility for the user application.
-
Product
cDAQ-9174, 4‑Slot, USB CompactDAQ Chassis
781157-01
-
4‑Slot, USB CompactDAQ Chassis - The cDAQ‑9174 is a CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements. It also controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9174 also has four 32‑bit general-purpose counters/timers. With multiple timing engines, you can run seven hardware-timed operations simultaneously, with three independent rates for analog input.
-
Product
Programmable Gain Amplifiers
-
Analog Devices programmable gain amplifiers (PGAs) provide excellent gain accuracy, channel-to-channel matching specifications, and low 1 ppm/°C drift. Set your gain with a simple serial or parallel interface from 1 V/V to over 4000 V/V.
-
Product
Multi-format Video Generator
LT 4600A
-
The LT 4600A multi-format video generator is a compact, 1U half-rack size SDI video signal generator that supports the triple-rate SDI (3G-SDI/HD-SDI/SD-SDI) format. In addition to test pattern output including color bars and SDI check fields, the LT 4600A is equipped with numerous features such as ID characters, QVGA logo marks, safety area markers, audio embedding, genlock function for external reference input signals, and three analog black signal outputs.
-
Product
Load Switches
-
Analog Devices load switches provide a highly integrated solution for switching voltage rails on in a controlled manner via an internal, high-side switch. This portfolio features overcurrent and overtemperature protection and supports currents up to 3 A. They provide a very low pass element RDSON to reduce power losses. The combination of the functionality and integration levels of ADI load switches make them extremely well-suited to inrush control applications for pluggable optical modules, line side pluggable interfaces protection, power plane switching, and power rail sequencing applications.
-
Product
Arria 10 FPGA Card
CP-FPGA-5
-
The Arria 10 FPGA PCIe card features a powerful field programmable gate array chip that supports both analog and digital I/O. Each card’s I/O functionality is fully customizable by the user by means of the FPGA Workbench tools. The cards are available with 480K or 1150K logic elements. There are two High Pin Count FMC Style Positions available for the High-Speed Daughter Cards.
-
Product
DSP-Based 4/8-Axis Advanced Motion Controllers
PCI-8254/8258
-
ADLINK's new PCI-8254 and PCI-8258 incorporate up-to-date floating-point DSP and FPGA technology to provide high-speed and high performance hybrid analog and pulse-train motion command. Leveraging ADLINK Softmotion technology, the PCI-8254/PCI-8258 offer more comprehensive and application-oriented motion functions to reduce the development time but maintain superior throughput and accuracy. Also delivered is excellent synchronous motion control performance.
-
Product
Random Access Monochromator
DeltaRAM X
-
The patented DeltaRAM™ X microscope Illuminator is the ideal fluorescence illuminator for quantitative intracellular ion research. It utilizes a galvanometer-based Random Access Monochromator (RAM) that can switch between any wavelength in 2 milliseconds. The DeltaRAM™ X is a complete, self-contained, illuminator that includes a power supply, high intensity xenon light source, DeltaRAM™ X monochromator, TTL shutter and flexible liquid light guide. The wavelength position is a simple analog voltage control. All you need to add is a microscope adapter for your fluorescence microscope and a USB or PCI DAC interface depending on the software you will be using to drive the illuminator.
-
Product
Counter And Rate Meters
-
We carry a wide range of counter and rate meters including totalizers, batch controllers, and more. Available with pulse, magnetic or DC pulse, analog, voltage, current, and frequency input types.
-
Product
Multifunctional I/O Module
DP-OBC-1122
-
DP-OBC-1122 is a standard 3U cPCI Multi-Functional IO module. This board operates on 32bit, 33MHz PCI bus. The key function of the module is to provide analog IO interface, in addition to the various communication interfaces such as ARINC429, RS422 and Rs232.It has an ADC, operating with ±10V analog input catering for 8 single ended / 4 differential ended channels and a DAC which provides 4 channels of analog signals with a maximum output voltage of ±10V .The module also features standard communication channels and general purpose IOs.
-
Product
NI-9361, 32-Bit, 8-Channel C Series Counter Input Module
783407-02
-
32-Bit, 8-Channel C Series Counter Input Module - The NI‑9361 is a differential or single-ended input module. With this module, you can expand beyond the four counters in CompactDAQ to reach up to 64 counters per 8‑slot chassis. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal switchable 1 kΩ pull‑up resistor. The NI‑9361 counters can perform encoder position and velocity measurements. You can synchronize the counters with other analog, digital, and counter measurements in your chassis.
-
Product
PCI-5114 , 125 MHz Bandwidth, 2-Channel, 8-Bit PCI Oscilloscope Device, 8 MB
779745-01
-
125 MHz Bandwidth, 2-Channel, 8-Bit PCI Oscilloscope Device—The PCI‑5114 low-cost oscilloscope device has two channels that sample up to 250 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require flexible measurement configurations and up to 125 MHz of analog bandwidth.
-
Product
Scientech Multi Instruments
-
Scientech Technologies Pvt. Ltd.
Variety of Instruments are being used in education, industry and research in the field of analog, digital, instrumentation, control system, biomedical and RF domain, requirement of these instruments varies and depends on their application areas.Some application like electronic, electrical, automation, etc. require standard waveforms, arbitrary waveforms, variable digital pattern and protocol generation. Analog signal combination and multiple digital signals are also required for some applications like power electronics, embedded, DSP and VLSI.
-
Product
Modulators
-
A modulator is an electronic circuit that superimposes a low-frequency (information) signal onto a high-frequency (carrier) signal for the purpose of wireless transmission. The reason for this is that higher frequency signals can be received using shorter aerials, which are more practical than longer ones. The information signal can be either analog or digital.
-
Product
Accelerometers
-
Analog Devices accelerometers and iSensor® MEMS accelerometer subsystems provide accurate detection while measuring acceleration, tilt, shock, and vibration in performance driven application. Our portfolio leads the industry in power, noise, bandwidth, and temperature specifications, and offers a range of MEMS sensor and signal conditioning integration on chip. Our MEMS-based Circuits from the Lab® reference designs have been built and tested by ADI experts to help you jumpstart your next system design.
-
Product
8-Ch, 16-Bit Isolated Analog Input EtherCAT Remote I/O Module
AMAX-4817
-
Suitable for EtherCAT networks8-ch, 16-bit analog input channels with 2,500 VDC isolation±275 V high common-mode voltage rangeQuick removable European type connectorSupports EtherCAT Distributed Clock (DC) mode and SyncManager modeTwo rotating switches for up to 256 slave IDs
-
Product
150 KS/s, 12-Bit, 16-Ch Multifunction USB Module
USB-4711A
-
Supports USB 3.0 SuperSpeedBus-powered16 analog input channels12-bit resolution AISampling rate up to 150 kS/s8-ch DI/8-ch DO, 2-ch AO and one 32-bit counterDetachable screw terminal on modulesSuitable for DIN-rail mountingOne lockable USB cable for secure connection includedPortable
-
Product
Channel Expanders
-
*Expand up to 384 Analog Channels + Digital Channels*Network interface allows remote operation via TCP/IP*Auto start / auto record*Remote Start Switch*Optional Driver Display
-
Product
MIPI Total Display IP Solution
DSI
-
The Arasan MIPI Display Serial Interface (DSI) Controller IP provides both device and host functionality. Additionally, the DSI Controller provides a high-speed serial interface between an application processor and display and follows a rigorous verification methodology to ensure interoperability of our DSI digital controller with our D-PHY analog IP. Arasan’s DSI solutions are MIPI standards-compliant and are designed to accelerate integration, lower risk and accelerate time to market for developers of display applications. Arasan’s expertise is backed by our unique silicon proven design discipline and product development process that ensures fast silicon success with our analog and digital IP.
-
Product
Digital Control VGAs
-
Analog Devices digital controlled variable gain amplifiers provide discrete levels of gain control over a fixed number of control bits for a variety of audio and optical frequency bands. Our VGAs improve the dynamic range of a circuit by allowing users to adjust the amplitude of a signal in real time, which is critical for a number of applications involving ultrasound, speech analysis, radar, wireless communications, and instrumentation. We also offer a portfolio of voltage controlled VGAs to provide you with continuous gain control over a wide dynamic range.
-
Product
12-/16-bit 16 Channel DAC for CompactPCI
CPCI395
-
The CPCI395 features 16 analog voltage outputs, integrated on the CompactPCI standard. Each output has a 12- or 16-bit resolution and a software programmable output range (0..+10V or -10..+10V). Control of the analog output is as easy as writing the binary equivalent to a dedicated register (per channel). Conversion takes place automatically. If desired, channels can be synchronized by presetting the channels and then give a simultaneous update command.
-
Product
Data Recording System
Director DII - DFR DDR
-
Using the Microsoft Windows 10® operating system, DII features complete Transient and Long-Term Phasor Data Recording, Analysis, and Transmission. E-MAX DII has a maximum capacity of 128 Analog and 256 Digital directly connected channels.
-
Product
PCIe-5763, 16-Bit, 500 MS/s, 4-Channel PCI FlexRIO Digitizer Device
786167-01
-
The PCIe-5763 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PCIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
Handheld Signal Level Meter
CT-DLM870D
-
The CT-DLM870D is a hand held signal level meter capable of reading analog, digital QAM and digital off air signal levels as well as Carrier to Noise, Bit Error Rate (BER), Modulation Error Rate (MER) and tilt.
-
Product
PCI-5154, 1 GHz Bandwidth, 2 GS/s, 8-Bit PCI Oscilloscope Device
780320-01
-
1 GHz Bandwidth, 2 GS/s, 8-Bit PCI Oscilloscope Device - The PCI‑5154 high-speed oscilloscope device has two channels that sample up to 2 GS/s with flexible settings for coupling, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 1 GHz of analog bandwidth and flexible measurement configurations.
