Switching
Controls consisting of a mechanical or electrical or electronic device for making or breaking or changing the connections in a circuit. (www.cogsci.princeton.edu)
See Also: Switching Matrix, High Voltage Switching, Switching Matrices, Multiplexers, General Purpose Switch
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Tinned Ends, 1 Amp, 1m, 500 Port
A500RMR-T-1B100
-
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This cable assembly isy is for direct connection to products using the 500-Pin SEARAY connector.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 20 MS/s on 4 Channels (Single Ended) or 2 Channels (Differential)
M2P.5922-X4
-
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
Standard 1.10 (31.18) - 4.80 (136.00) Switch Probe
TSP100-J100-1
-
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
Product
LXI 75Ω 6:1 Microwave Multiplexer 16-bank 2.5GHz 1.6/5.6
60-820-016
-
Our 60-820 Microwave Multiplexer range is suitable for switching 75 ohm signals up to 2.5GHz. With the capability of supporting up to 16 banks of 6 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted DIN1.6/5.6 style connectors. A 50 ohm version, the 60-800, is also available covering frequencies to 20GHz.
-
Product
Detector, Metal, Power, Stud
72-6792
-
*Electronically locates hidden cables gas and water pipes*Traces hidden ceiling joists and wall studs*Senses presence of mains power withut touching live wires*Locates breaks in circuits and cables*Identifies faulty plugs switches and sockets*Incorporates audio signal and indicator light
-
Product
PXI/PXIe High Voltage Multiplexer, Dual 11-Channel, 2-Pole
42-321-125-HI
-
The 40-321-125-HI (PXI) and 42-321-125-HI (PXIe) are dual 11-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
Programmable Delay Modules Instrument
The XS Series
-
Our XS series utilizes solid-state PIN diode technology to give you the fastest switching speed
-
Product
PXI 2A Multiplexer, 1-Bank, 8-Channel 16-Pole
40-614-019
-
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
MCX Male to BNC Male Cable, 50 Ohm, 1 m
188375-01
-
The MCX-BNC Coaxial Cable is used for modular instruments such as PXI switches. This cable is available in 1 m and 30 cm lengths.
-
Product
PXI 8 Slot BRIC Matrix, Solid State, 192x8, 1-Pole (6 sub-cards)
40-563B-121-192X8
-
The 40-563B-121-192x8 is an ultra high density 8-slot matrix module with 1-pole switching and is part of our range PXI BRIC matrices. They are available in 2, 4 or 8-slot sizes to suit high performance PXI switching requirements and are constructed using solid state switches.
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Tinned Ends, 1 Amp, 0.5m, 500 Port
A500RMR-T-1B050
-
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This cable assembly is for direct connection to products using the 500-Pin SEARAY connector (not compatible with Pickering products).
-
Product
PXI 2A Multiplexer, 1-Bank, 16-Channel, 8-Pole
40-614B-018
-
This 1-bank, 16-channel, 8-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Low PIM Coaxial Switch, DC to 26.5 GHz, SP4T
87104R
-
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87104R is a low PIM SP4T coaxial switch, operating from DC to 26.5 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
Product
Switches
-
Panasonic Industrial Devices Sales Company of America
Dedicated to providing the highest level of quality, Panasonic offers customers Electronic Switches that improve a device’s overall user experience.
-
Product
PCI 2 Amp Multiplexer, Dual 8-Channel, 2-Pole
50-635A-106
-
The 50-635A-106 is a dual 8-channel, 2-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
LXI High Density Dual 32x64 2A Matrix
60-552-011
-
A high-density single pole LXI matrix module capable of switching up to 300VDC/250VAC, 2A (60W max). The use of high-quality electro-mechanical relays offers high switching confidence for signal routing in large ATE systems.
-
Product
LXI Microwave Multiplexer, SP6T, 10-Bank, 50GHz, 50Ω, SMA-2.4, Terminated
60-800-710
-
High performance RF multiplexer suitable for switching microwave signals up to 50GHz with automatic termination of unused signals
-
Product
LXI High Voltage Switching - 40xSPST Plugin Module
65-233-701-HI
-
The 65-233-701-HI plug-in module is part of a scalable high voltage switch platform that provides a high voltage switching solution with capability up to 7 kV. Switch arrays are created by populating the 65-200-002 scalable chassis with plug-in modules that provide access to the switches on 51-pin front panel connectors. Users can specify as many or as few plug-in modules as they require and can field upgrade the chassis to extend the number of switches.
-
Product
10A DIGITAL MICRO-OHMMETER
MPK-2000e
-
The MPK-2000e digital very low resistance ohmmeter is a portable, microprocessor controlled instrument used to accurately measure resistances of switches and circuit breaker contacts, transformer and motor windings, wire and cable samples, joints in busbars, etc., using test currents from 1mA up to 10A. It uses the Kelvin-type, four-terminals measurement principle, thus eliminating errors caused by lead and contact resistances.
-
Product
PXI 10A Power MUX, 2-Bank, 8-Channel
40-661-102
-
The 40-661 is a single pole power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available. Signal connections are made via front panel mounted 20-way GMCT plugs.
-
Product
Gateways And Bridges
-
Handle your single X.25 line to TCP/IP migration requirements. The FarLinX Mini Gateway supports XOT to X.25 switching, X.25 to TCP data translation and connection routing, TCP to XOT, a Triple-X PAD, and a Host PAD. The FarLinX Connect Mini v2 offers HDLC Bridging and conversion.
-
Product
PXI 8 Slot BRIC Solid State 128x8 1-Pole (4 sub-cards)
40-563A-121-128X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Limit Switches
-
Panasonic Automotive & Industrial Systems Europe GmbH
Compact designHigh load capabilityEconomicLow weightIP64
-
Product
Transimpedance Amplifiers
-
Current-to-Voltage Amplifier for use with Photodiode-Based Detectors. Transimpedance Amplifiers, Standalone Devices with Data Acquisition as well as Display Function (Optometer). Log/Lin Switching Amplifiers, etc.
-
Product
903 Benchtop Three Phase 40A
-
Weshine Electric Manufacturing Co., Ltd
1. The instrument has standard four phase voltage and three-phase current output. It can test not only various traditional relays and protection devices, but also various modern microcomputer protections, especially for transformer differential protection and standby automatic switching device. The test is more convenient and perfect.2. Classic Windows XP operation interface, friendly man-machine interface, easy and fast operation; high performance embedded industrial control computer and 8.4 inch resolution 800 × 600 TFT true color display screen, can provide rich and intuitive information, including the current working state of the equipment and various help information.
-
Product
50 Ohm SMB to SMB Cable Assembly
40-977-511-1m
-
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
5-Port Coaxial Switch, DC to 18 GHz
8764B
-
Frequency range DC to 18 GHzUnterminated multiport coaxial switch with five RF portsInsertion loss: < 0.20 dB to 2 GHz, < 0.5 dB to 18 GHzSWR (through line): < 1.1 to 2 GHz, < 1.2 to 12.4 GHz, < 1.3 to 18 GHzIsolation: > 90 dB to 18 GHzLong life > 1 million cyclesHigh repeatability: < 0.03 dB typicalCurrent interrupts and position indication capability
-
Product
Low PIM Coaxial Switch, DC to 26.5 GHz, SP6T
87106R
-
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87106R is a low PIM SP6T coaxial switch, operating from DC to 26.5 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
Product
PXI/PXIe Microwave Relay, Triple SPDT, 2.5 GHz, 75 Ω, 1.6/5.6, Failsafe
42-780B-753
-
The 40-780B-753 (PXI) and 42-780B-753 (PXIe) are triple failsafe SPDT 2.5 GHz 75 Ω unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
Product
SWB-2816, 8x46, 0.3 A, No Row Access, Reed Relay Matrix Module for SwitchBlock
781421-16
-
8x46, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2816 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
